Exabyte Mammoth Manuale utente
319932-000
December 1996
#319932-000#
Contents
1 Before you begin . . . . . . . . . . . . . . . . . . . . . . . 2
2 Disconnecting the LCD flex cable. . . . . . . . . . 3
3 Replacing the faceplate. . . . . . . . . . . . . . . . . . 4
4 Connecting the LCD flex cable . . . . . . . . . . . . 6
5 Replacing the top cover . . . . . . . . . . . . . . . . . 7
6 After replacing the faceplate . . . . . . . . . . . . . 8
FIELD INSTRUCTIONS
Exabyte Mammoth 8mm Tape Drive
1
Replacing the Faceplate
Page 2 of 8 319932
Copyright
Copyright 1996 by Exabyte Corporation. All rights reserved. This item and the information contained
herein are the property of Exabyte Corporation. No part of this document may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise, without the express written permission of Exabyte Corporation, 1685 38th Street, Boulder,
Colorado 80301.
Trademark Notices
EXABYTE, EXAPAK, EXB, FileSECURE, LANCourier, and NetSECURE are registered trademarks of
Exabyte Corporation. Eagle, EXA, EXAFacts, EXA
soft
, EXATAPE, Nest, and SCIMON are trademarks of
Exabyte Corporation. All other product names are trademarks or registered trademarks of their
respective companies.
1 Before you begin
To protect the tape drive from ESD, follow these procedures when repairing
or testing it:
§
Place a static protection mat on the work surface used for tape drive
components. Use a 1-megohm resistor to ground the static protection
mat.
§
Wear a static protection wrist band whenever you handle tape drive
printed circuit cards. Connect this wrist band to the static protection mat
or to other suitable ESD grounding.
If there is a cartridge in the tape drive, remove it before performing any
maintenance procedure.
Required tools
§
Torque limiting screwdriver
§
T-6 TORX bit
CAUTION
Before you begin, make sure that the repairenvironment
for the tape drive is free of conditions that could cause
electrostatic discharge (ESD).
December 1996 Page 3 of 8
2
Disconnecting the LCD flex cable
2 Disconnecting the LCD flex cable
If your tape drive has an LCD, follow the instructions in this section to
disconnect the LCD flex cable before you remove the faceplate.
If your tape drive does not have an LCD on the faceplate, skip this section
and go to Replacing the faceplate on page 4.
1.
Using a T-6 screwdriver, remove the two side screws and one rear screw
that attach the top cover to the tape drive (see Figure 1).
2.
To remove the top cover, slide it back about1 inch (2.6 cm). Lift the front
edge first, and then remove the cover.
Figure 1
Removing the top cover
Page 4 of 8 319932
3
Replacing the faceplate
3.
Unlock the LCD flex cable connector by pulling one end of the tab and
then the other toward the cable (see Figure 2).
4.
Gently pull the LCD flex cable out of the connector.
3 Replacing the faceplate
Note:
The instructions in this section apply to both LCD and non-LCD
faceplates. However, the illustrations in this section show a
faceplate with an LCD.
1.
Press in the faceplate tabs on both sides of the tape drive, as shown in
Figure 3. Pull the faceplate straight out from the tape drive.
Figure 2
Loosening the LCD flex cable connector
CAUTION
Make sure you pull the faceplate straight out to remove
it. If you tilt or twist the faceplate, you could damage
the LED card on the left side of the tape drive.
December 1996 Page 5 of 8
3
Replacing the faceplate
2.
If you are replacing a non-LCD faceplate with an LCD faceplate, follow
the instructions on page 3 to remove the top cover of the tape drive.
3.
Placethetapedriveonaflatsurface.Alignthebottomofthereplacement
faceplate with the bottom of the tape drive. Position the LED guard on
the back of the faceplate on the left side of the tape drive.
4.
Position the faceplate tabs inside the side panels, as shown in Figure 4,
and press the faceplate onto the tape drive.
Figure 3
Removing the faceplate
CAUTION
Make sure you align the bottom of the faceplate with
the bottom of the tape drive and position the faceplate
tabs inside the side panels before you attach the
faceplate. If you misalign the faceplate, you could
break the LEDs off the printed circuit card.
Figure 4
Positioning the faceplate
Page 6 of 8 319932
4
Connecting the LCD flex cable
5.
If your replacement faceplate has an LCD, follow the steps in the next
section to connect the LCD flex cable.
If your replacement faceplate does not have an LCD and you removed
the top cover, skip the next section and go to Replacing the top cover
on page 7.
If your replacement faceplate does not have an LCD and you did not
remove the top cover, skip the next two sections and go to After
replacing the faceplate on page 8.
4 Connecting the LCD flex cable
1.
Unlock the LCD flex cable connector by pulling one end of the tab and
then the other toward the cable (see Figure 5).
2.
Slide the LCD flex cable allthe way into the connector on thecard. Make
sure the LCD flex cable is firmly seated in the connector.
3.
Holding the flex cable firmly in place, press the tab into the connector
to close it.
Figure 5
Loosening the tab on the LCD flex cable connector
December 1996 Page 7 of 8
5
Replacing the top cover
5 Replacing the top cover
1.
Place the top cover on the tape drive so that the back edge extends about
1 inch (2.6 cm) over the back of the tape drive. Slide the cover forward
carefully, guiding the tab on the top cover under the lip of the faceplate.
2.
Replace the three screws that attach the top cover to the tape drive (see
Figure 6). Tighten the screws to 1.2 inch-pounds of torque.
CAUTION
A mylar flap inside the tape drive protects the cartridge
loader. Be careful not to catch the flap on the top cover
window as you slide the top cover forward.
Figure 6
Replacing the top cover screws
Page 8 of 8 319932
6
After replacing the faceplate
6 After replacing the faceplate
Apply power to the tape drive and insert a cartridge. Check the following
items:
§
Make sure the cartridgedoes not get caught on the faceplate during load
or unload operations.
§
When you remove the cartridge, make sure the tape drive door closes.
§
If you have a faceplate with an LCD, make sure the LCD operates
correctly. Refer to
Exabyte Mammoth Installation and Operation
(part
number 306484) for more information about the LCD.
If you experience problems, make sure the faceplate is positioned squarely
on the front of the tape drive and the LCD cable is securely seated in the
connector.
Altri manuali per Mammoth
4
Indice
Altri manuali Exabyte Magazzinaggio
Exabyte
Exabyte EXB-8205 Manuale utente
Exabyte
Exabyte EXB-8200 Manuale utente
Exabyte
Exabyte Mammoth Manuale utente
Exabyte
Exabyte 8505XLS Istruzioni operative originali
Exabyte
Exabyte Mammoth Manuale utente
Exabyte
Exabyte Mammoth Manuale del proprietario
Exabyte
Exabyte EXB-8500 Manuale del proprietario
Exabyte
Exabyte Mammoth-LT Manuale del proprietario
Exabyte
Exabyte VXA-172 Manuale utente
Exabyte
Exabyte X200 Library Manuale del proprietario
Exabyte
Exabyte Magnum20 Manuale di istruzioni
Exabyte
Exabyte VXA-2 Manuale utente
Exabyte
Exabyte VXA-2 AUTOPAK1X7 Manuale utente
Exabyte
Exabyte VXA-1 Manuale utente
Exabyte
Exabyte 221L Manuale utente
Exabyte
Exabyte 8505XLS Manuale utente
Exabyte
Exabyte EXB-8500 Guida
Exabyte
Exabyte EXB-8700 Manuale utente
Exabyte
Exabyte Mammoth-2 Manuale utente
Exabyte
Exabyte 430 Manuale utente
