EXMITTER EX2 Manuale utente
EXMITTER -- Professional Remote Control Products Expert
2 EXMITTER EX2 Digital Radio System
All instructions, warranties and other collateral documents are
subject to change at the sole discretion of VolantexRC Co., Ltd..
Visit www.volantexrc.com for up-to-date product literature.
NOTICE
The following terms are used throughout the product literature
to indicate various levels of potential harm when operating this
product.
CAUTION: Procedures, which if not be properly followed, is able to
create a possibility of physical property damage AND or possibility
of injury.
Read the ENTIRE instruction manual to become familiar
with the features of the product before operating. Fail to
operate the product correctly can result in damage to the
product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must
be operated with caution and common sense and requires some
basic mechanical ability. Fail to operate this Product in a safe
and responsible manner could result in injury or damage to the
product or other property. This product is not intended for use
by children without direct adult supervision. Do not attempt
to disassemble , use with incompatible components or augment
product in any way without the approval of VolantexRC Co., Ltd..
This manual contains instructions for safety, operation and
maintenance. It is essential to read and follow all the instructions
and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.
WARNING
Age Recommendation:
Not for Children under 14 years. This is not a toy.
3 EXMITTER EX2 Digital Radio System
Antenna
Steering Trim
5:5 / 7:3 Switch
Throttle Reverse
Steering Reverse
Indicator LED
Bind Button
Steering Wheel
Throttle Trigger
Throttle Trim
Steering Rate
Simulator Cable
Slot
ON/OFF
• Always ensure all batteries have been properly charged prior to
using the model.
• Always check all servos and their connections prior to each run.
• Never operate your model near spectators, parking areas or any
other area that could result in injury to people or damage of property.
• Never operate your model during adverse weather conditions. Poor
visibility can cause disorientation and loss of control of your model.
• Never point the transmitter antenna directly toward the model. The
radiation pattern from the tip of the antenna is inherently low.
• If at any time during the operation of your model
you observe any erratic or abnormal operation, immediately stop
operation of your model until the cause of the problem has been
ascertained and corrected.
TRANSMITTER DETAILS
SAFETY PRECAUTIONS
4 EXMITTER EX2 Digital Radio System
Solid Green:
Battery is in good
condition (Above 4.3V)
Flashing Green:
Battery is at low
voltage
Replace batteries
ON / OFF Switch BATTERY LED MONITOR
Slide the switch UP
for ON and DOWN
for OFF
Adjust the proportion of throttle signal on either side of the center
trigger position. You can pick which proportion of forward/reverse you
prefer. We recommend using the 7:3 position for most applications.
7:3 / 5:5 Switch Instruction
Switch Up for 7:3 Switch Down for 5:5
If the direction of travel on the
rudder is backwards, slide the
steering reverse switch to the
other position.
It is Same principle for the
throttle reverse switch.
Steering Reverse
Throttle Reverse
SERVO REVERSING SWITCHES
Rotating the knob clockwise will
give you greater range in rudder
movement.
Counter-clockwise will reduce
the range of rudder movement.
Adjust to suit your driving style
and preferences. Steering Rate
Knob
STEERING RATE KNOB
5 EXMITTER EX2 Digital Radio System
The throttle trim dial is used to
adjust the throttle trim when
the throttle stick is released
(neutral position). This is typically
used to adjust the brakes.
Rotating the dial causes the
throttle trim (the throttle position
at rest) to be changed.
Throttle Trim
Throttle TRIM
Steering Trim
The steering trim dial is used to
adjust the steering trim when
the wheel is centered.
Rotating the dial changes the
steering trim (the steering at rest
position). Normally, the steering
trim is adjusted until the vehicle
tracks straight.
STEERING TRIM
Install the Receiver in your vehicle using double-sided Velcro. Velcro
will hold the receiver in place and help isolate it from vibrations.
Mount the antenna up and away from the vehicle in an antenna tube.
The higher up the antenna is, the better signal it will receive.
CAUTION: Do not cut the antenna.
INSTALL YOUR RECEIVER
RECEIVER
ELECTRICAL
BATTERY
ELECTRONIC
SPEED CONTROL
STEERING
GAS INSTALLATION THROTTLE
RECEIVER
BEC
6 EXMITTER EX2 Digital Radio System
The EX2 comes with the receiver failsafe set to NONE. In the event
of loss of signal the motor will stop and the vehicle willdrift. If the
signal is regained normal function willreturn. If you wish to program
the failsafe to a custom setting just follow these simple steps:
1. With both the transmitter and receiver powered ON, press the bind
button on the receiver for about 3 seconds.
2. The receiver will enter the failsafe setting menu and the receiver
LED will ash.
3. You have about 3 seconds to move the controls to the position that
you wish to program into failsafe.
4. After the 3 seconds the receiver will save the settings and return to
normal mode.
5. If you wish to reset to a different setting, simply repeat the above
steps.
CAUTION: DO NOT leave the bind cable in the bind channel
plug after binding nished, otherwise the binding program will
work automatically each time when you power on the receiver.
FAILSAFE Setting
Binding is the process of programming the receiver to recognize
the GUID (Globally Unique Identifier) code of a single specific
transmitter. When a receiver is bound to a transmitter, the receiver
will only respond to that specic transmitter. If you need to rebind for
any reason, please follow these steps:
1. With the transmitter switched OFF
2. Insert the bind cable to bind channel slot.
3. Power on the receiver, then turn on the transmitter with pressing
on the bind button within 5 seconds after receiver is power on.
4. Loose the bind button and wait for about 5 seconds.
5. After the receiver stop blinking, it means the binding is nished
6. Unplug the bind cable and then you are ready to run.
BIND BUTTON
FailSafe
RECEIVER CONNECTION
Bind Cable
BINDING
Antenna
7 EXMITTER EX2 Digital Radio System
Push the trigger slightly away
from you to arm the motor
Pull the trigger towards you to
make the vehicle go forward.
HOW TO OPERATE YOUR VEHICLE
The proportional speed control
means the farther you pull it the
faster the vehicle will go.
Release the trigger to stop.
When you upgrade to brushless
speed control with the reverse
function, pushing the throttle
trigger forward will make the
motor run in reverse and back
the vehicle up.
Rotate the steering wheel
clockwise while holding the
trigger to turn right. If the
steering is not tight enough,
increase the travel volume by
rotating the travel rate knob
clockwise till you reach the
desired amount.
8 EXMITTER EX2 Digital Radio System
Rotate the steering wheel
counter-clockwise while holding
the trigger to turn right. If the
steering is not tight enough,
increase the travel volume by
rotating the travel rate knob
clockwise till you reach the
desired amount.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
0890
Company Name: VOLANTEXRC CO., LTD. Add: 2nd Building Fuxi
Dongqiao Industrial Park,
Shanzhang Road Shantou, China
Product Name: RADIO CONTROL PRODUCT Item No: V792
Indice
Altri manuali EXMITTER Telecomando
