Exsys EX-6007POE Manuale utente
1
Thank you for purchasing this Gigabit PoE Injector. It was designed to
add 56 VDC power to an Ethernet port so you can deliver power and
data over a single Ethernet cable to your Ethernet device in the field.
Features:
✓Provides power to remote network devices
✓Supports 10/100/1000 Base-T Ethernet standards
✓Fully IEEE 802.3at compliant PoE (PSE) type 1 and 2 operation
✓Maximum Power Delivered:
Type 1: 13W
Type 2: 25.5W
✓One DC-Jack and one TB-2 for 12~24V DC power input
✓Supports one PoE power enabled LED indicator
✓One Ethernet Data and one PoE RJ45 connectors
✓Built in step-up converter from 12~24V DC to 56 VDC
✓Small Rugged Metal Housing for critical applications
✓Provides direct panel and DIN Rail mounting methods
Gigabit PoE Injector
with DIN-Rail Mounting Kit
Installation Guide
1. Introduction
2. Connector Layout
Power LED
Power input
terminal blocks
PoE LED
(Amber)
No connection)
Data input
port
PoE output
port
Power input
DC-jack
Gigabit PoE Injector with DIN-Rail Mounting Kit
2
DC-jack and 2-pin terminator blocks for power input: To inject the
DC power to the Ethernet cable, the Injector needs a 12~24V DC
power applied either on its DC jack or the 2-pin terminal blocks
(but not both at the same time), its internal circuits will convert it to
56V DC to use for PoE.
Warning!!
Please make sure the polarity of the input power should be
correctly match the terminal block pins, otherwise it will damage
the Injector.
Power LED: It Lights up when the 12~24V DC power is being
applied. It is OFF when no power is applied on DC jack or terminal
blocks.
LAN Data input port: RJ45 connector for the data input. It accepts
10/100/1000Gbps Ethernet data cable.
PoE output port: RJ45 connector that is able to be added 56V DC
power with the input Ethernet data. If there is a PoE PD was
connected, the Injector will supply the PoE power and lights up
the Amber LED. Otherwise, it won’t apply any power on the cable
and the Amber PoE LED will NOT light up.
1. Connect data cable to RJ45 connector marked as “LAN”
2. Apply DC power (12~24V) to the DC jack or 2-pin Terminal Blocks
Connector. The Power LED should light up. If you are applying the
power on the 2-pin terminal blocks instead, please note its
polarity should match the marking next to the terminal blocks’
pins.
3. Connect your PoE PD device to the PoE port, the Amber PoE LED
should light up if the PD was detected and powered by the
Injector
3. Hardware Installation
+12~24V
GND
+
-
Gigabit PoE Injector with DIN-Rail Mounting Kit
3
The metal DIN-Rail attachment clip should be used when you are
mounting the Injector onto a DIN-Rail. The clip came with 2 screws to
fix it on the rear side of the Injector.
Operating temp.: 0 to 55C (32 to 131F)
Operating humidity: 5 to 95% RH
Dimensions (LxWxH): 4.51 x 2.25 x 1.03 in
(114.60 x 57.26 x 26.20 mm)
5. Environmental Specifications
4. DIN-Rail Mounting
DIN-Rail Clip
Fixing screws
Gigabit PoE Injector with DIN-Rail Mounting Kit
4
6. Mechanical Drawings
Indice
Altri manuali Exsys Interruttore
Exsys
Exsys EX-1163HMS-WT Manuale utente
Exsys
Exsys EX-3460 Manuale utente
Exsys
Exsys EX-1181HMS Manuale utente
Exsys
Exsys EX-11214HMVS Manuale utente
Exsys
Exsys EX-6128 Manuale utente
Exsys
Exsys EX-1184HMVS-2 Manuale utente
Exsys
Exsys EX-1116HMVS Manuale utente
Exsys
Exsys EX-1112HMS Manuale utente
Exsys
Exsys EX-1179HMVS Manuale utente
Exsys
Exsys EX-6002 Manuale utente
Exsys
Exsys EX-1247HMVS Manuale utente
Exsys
Exsys EX-1113HMS Manuale utente
Exsys
Exsys EX-6128PoE Manuale utente
Exsys
Exsys EX-1186HMVS Manuale utente
Exsys
Exsys EX-1330M Manuale utente
Exsys
Exsys EX-1170HMVS Manuale utente
Exsys
Exsys EX-1170HMVS Manuale utente
Exsys
Exsys EX-1178 Manuale utente
Exsys
Exsys EX-1167 Manuale utente
Exsys
Exsys EX-1177HMVS Manuale utente
