Extech Instruments CO210 Manuale utente

USER MANUAL

CO2Monitor and Datalogger

Model CO210

2CO210-en-US v1.3 1/21

Introduction

Congratulations on your purchase of the Model CO210 Carbon Dioxide Monitor and Datalogger.

The CO210 measures, displays, and logs CO2level, air temperature, relative humidity, date, and

time. The included Windows-based software and USB cable allow you to set up the datalogger

and transfer logged data to your PC. The CO210 is an ideal instrument for indoor air quality (IAQ)

monitoring. The CO210 is shipped fully tested and calibrated and, with proper use, will provide

years of reliable service.

Description

METER DESCRIPTION

1. LCD Multifunction display

2. Power LED indicator (blinks while datalogging)

3. Control buttons

Power adaptor jack, USB port, and sensors on back of meter

LCD DESCRIPTION

1. CO2concentration in ppm

2. Date and Time

3. Air Temperature

4. % Relative Humidity

FUNCTION INDICATORS

ppm CO2measurement units

GOOD/NORMAL/POOR CO2air quality levels

Air Temp Air Temperature

Humidity % Relative Humidity

°C or °F Temperature units

MIN/MAX Minimum and Maximum readings

Fan icon flashes when the CO2alarm triggers

CONTROL BUTTONS

SET Long press to enter setup mode. Saves settings.

ESC Exits setup page/mode. Stops the datalogger. Aborts calibration.

RESET Long press to clear the MIN/MAX memories.

LOG ▲Start Datalogger. Select a mode or increase a value in the setup menu.

MIN/MAX ▼Access MIN/MAX function. Use as down-arrow in setup mode.

Long press SET, ▼and

▲

to enter the CO

calibration

3CO210-en-US v1.3 1/21

Operation

Powering the CO210

Plug the supplied power adaptor (5V/0.5A) into the power jack on the back of the meter

and to an AC power source, the meter will switch ON. The front panel LED power

indicator will light, and the beeper will sound. If the power source voltage is incorrect,

‘bAt’will display, and the LED indicator will flash. Do not use the CO210 with an incorrect

power source.

In normal operation the LCD will display CO

, temperature, humidity, date, and time. The air

quality level is also displayed (GOOD, NORMAL, or POOR).

Measurements

The CO210 starts measuring as soon as it is powered and updates readings once per second. If

the operating environment changes (from high to low temperature, for example), it will require

2 minutes for the CO2 sensor to respond and 10 minutes for the humidity sensor to respond. Do

not hold the meter close to your mouth or any other source of CO2.

MIN/MAX Mode

In the normal mode, press the MIN/MAX button to see the minimum or the maximum CO2,

Temperature, and Humidity values. Each press of the MIN/MAX button steps through the MIN,

the MAX, and then the normal display mode. Long press the RESET button to clear the minimum

and maximum values from memory.

Data Logging

The CO210 logs CO

, air temperature, and relative humidity readings (along with date and

time). The memory capacity is 15999 points (5,333 CO

, temperature, and humidity

records). The sample rate is adjustable (in the setup mode) from 1 second to 4 hours, 59

minutes, 59 seconds.

After setting the sampling rate, long press the LOG button to start logging. The green

LED blinks while logging and the main display digits alternate between real time CO

readings and the abbreviation ‘rEC’(record). The lower displays show the real time

temperature, humidity, date, and time.

To stop logging, long press the

ESC

button

. The LED stops blinking, and the main display

will alternate between real time CO

readings and the word ‘End’. Long press the ESC

button again to return to the normal operating mode. See the PC Datalogger Software

section, next, for details on downloading logged readings to a PC.

Note that the MIN/MAX memory is still operational during data logging and is cleared

each time a logging session is started.

4CO210-en-US v1.3 1/21

PC Datalogger Software

The supplied Windows-based PC software and USB cable allow you to set-up the datalogger,

download logged data, and view the logged data graphically or in text format on a PC. The

software and USB driver is also available from the Extech website.

Connect the CO210 to a PC using the supplied USB cable. The USB port is located on the back of

the CO210. Install the software, open it, and refer to the program HELP utility for complete

operational information. Contact Extech support if you have questions or problems.

Alarm Function

The CO210 features an audible (beeper) and visual (flashing fan icon) alarm that warn when the

CO2concentration exceeds the programmed threshold. There are two alarm thresholds, the

‘POOR’air quality threshold (that triggers the alarm), and the ‘NORMAL’air quality threshold

(that cancels the alarm). See the Setup mode to set these threshold settings.

The audible alarm can be manually silenced by pressing any key, or it will automatically stop

when the CO2reading is no longer in the alarm region (the user can subsequently press and hold

the RESET button to re-activate the alarm, if desired).

If the beeper is manually silenced, it will sound again when readings

move out of, and then back into, the alarm region.

The fan icon continues to flash even when the beeper is manually

silenced. It disappears only when readings are no longer in the alarm

region.

Setup Mode

Long press the SET button to enter the setup mode.

P1.1: Threshold setting for the ‘GOOD’air quality display icon

When entering the setup mode, P1.0and ‘CO2’are displayed. Press the SET button again to

access P1.1for setting the CO2upper limit (threshold) for the ‘GOOD’air quality display icon. The

current set value will appear blinking on the display.

Press the ▲or ▼button to increase or decrease the value. Each press adjusts in 100 ppm

increments. The range is 0 to 700 ppm (default is 700 ppm).

When the value has been set, press the SET button to confirm the ‘GOOD’threshold and move

to P1.2for setting the ‘NORMAL’display threshold. Press the ESC button to exit without saving.

5CO210-en-US v1.3 1/21

P1.2: Threshold setting for the ‘NORMAL’air quality icon and the CO2Alarm

P1.2is used for setting the CO2high threshold for the ‘NORMAL’air quality display icon. It is also

the low threshold for the alarm beeper and the flashing fan alarm icon. The current set value

will appear blinking on the display.

Press the ▲or ▼button to increase or decrease the value. Each press adjusts in 100 ppm

increments. The range is 700 to 1000 ppm (default is 1000 ppm).

When the value has been set, press the SET button to confirm the ‘NORMAL’limit and move to

P1.3for setting the ‘POOR’display threshold. Press the ESC button to exit without saving.

P1.3: Threshold setting for the ‘POOR’air quality icon and CO2Alarm

P1.3is used for setting the high CO2threshold for the ‘POOR’air quality display icon, alarm

beeper, and flashing fan icon. The current set value will appear blinking on the display.

Press the ▲or ▼button to increase or decrease the threshold. Each press adjusts in 100 ppm

increments. The range is 1000 to 5000 ppm (default is 1000 ppm).

When the value has been set, press the SET button to confirm and move to P1.4. Press SET again

to continue.Press ESC to exit without saving.

Caution: Set the alarm value within the specified range of the CO210 where accuracy is

assured. Out of specification readings are for reference only.

P2.0 Temperature Units

Press the ▲button in P1.0mode to access P2.0for setting the temperature display units.

Press the SET button to access the P2.1 setting mode. The °C or °F will blink (default is °C).

Press the ▲button to change the units. Press the SETbutton to confirm the setting or press the

ESC button to exit without saving and return to P1.0.

6CO210-en-US v1.3 1/21

P3.0 Real-Time Calendar Clock

Press the ▲button in P1.0twice to access P3.0for setting the real-time calendar clock. Press the

SET button and the meter will access P3.1, showing the blinking YEAR on the lower left. To

change the year, press the ▲or ▼button. Press the SET button to save the setting and move to

P3.2(or press the ESC button to return to P3.0without saving).

Press the ▲button from P3.1to access P3.2. The current MONTH setting will blink. To change

the month, press the ▲or ▼button. Press the SET button to save the setting and move to P3.3

(or press the ESC button to return to P3.0without saving).

Press the ▲button from P3.2to access P3.3. The current DATE (day) setting will blink. To change

the day, press the ▲or ▼button. Press the SET button to save the setting and move to P3.4(or

press the ESC button to return to P3.0without saving).

Press the ▲button from P3.3to access P3.4. The current 12/24-hour clock setting will blink. To

change it, press the ▲or ▼button. Press the SET button to save the setting and move to P3.5

(or press the ESC button to return to P3.0without saving).

Repeat as above to finish setting P3.5(HOURS) and P3.6(MINUTES)

P4.0: Factory Default Reset

Press the ▲button in P1.0 three times to access P4.0 where you can reset the meter to its

default settings. Press SET and the meter will access P4.1 with a blinking “No”. Press the ▲to

switch the status to ‘Yes’and then press either the SET button to confirm and continue or the

ESC button to abort the process.

7CO210-en-US v1.3 1/21

P5.0 Data Logger Sampling Rate

Press the ▲button in P1.0 three times to access P5.0 to set the data logger sample rate. The

available range is 1 second to 4 hours, 59 minutes, 59 seconds.

Press the SET button to access P5.1, the HOUR digits will blink. To change the hour, press the ▲

or ▼button. Press the SET button to save the setting and then repeat this procedure for P5.2

MINUTES and P5.3 SECONDS (the SECONDS value is shown in the center display area). Press the

ESCbutton return to P5.0 without saving the setting.

Calibration

The meter is calibrated to a 400ppm CO2concentration at the factory. If the accuracy becomes a

concern, or after one year of use, return the meter to Extech for calibration or continue below.

ABC (Automatic Baseline CO2Calibration)

ABC (Automatic Baseline Calibration) establishes a baseline calibration to eliminate the zero drift

of the infrared sensor. The ABC function is always “ON” when the meter is powered.

ABC is designed to calibrate the meter at the minimum CO2reading detected over 7.5 days of

continuous monitoring (power on). It assumes that the area being tested receives fresh air with

a CO2level of approximately 400ppm at some point during the monitoring period. Note that It is

not suitable to use the CO210 in closed areas with consistently high CO2levels 24 hours a day.

Manual CO2Calibration

Manual calibration is suggested to be done outdoors on a clear day with good ventilation and

fresh air where the CO2level is approximately 400 ppm. Do not calibrate on a rainy day because

high humidity will affect the CO2level in air.

CAUTION: Do not calibrate the meter in an atmosphere of unknown CO2concentration. Do not

calibrate in places crowded with people, pets, plants, or where high CO2concentrations may

exist such as near ventilation ducts or fireplaces.

Place the meter in the calibration area and switch it on. Press and hold

the SET, ▲,and ▼buttons simultaneously for > 1 second to enter CO2

calibration mode. “400ppm”and “CO2” will blink while the calibration is

in process.

The calibration will require approximately five (5) minutes. When the calibration is complete, the

blinking stops and the meter returns to the normal operating mode. Press ESC to abort a

calibration session (not recommended).

8CO210-en-US v1.3 1/21

Specifications

Function

Range

Resolution

Accuracy

CO2

0 to 9999ppm

1ppm

± (5%rdg + 50ppm)

Temperature

-10 to 60°C (14 to 140°F)

0.1°

± 0.6°C (0.9°F)

Humidity

0.1 to 99.9%

0.1%

± 3% (10 to 90%)

± 5% (< 10% or > 90%)

Display

Multi-function LCD

Sensor Type

CO2: NDIR (non-dispersive infrared) technology

Humidity: Capacitance sensor

Temperature (air): Thermistor

Response

CO2: < 2min for 90% step change

Air temperature: < 2min for 90% step change

RH: < 10min for 90% step change

Datalogger

15999 total samples (5,333 readings each for CO2, air

temperature, and relative humidity).

To download logged readings, use the latest Windows-

based PC software and USB driver from the Extech

website. USB cable is included with the CO210.

Operating Conditions

14 to 140°F (-10 to 60°C); < 90% RH non-condensing

Storage Conditions

-4 to 140°F (-20 to 60°C); <99% RH non-condensing

Power Supply

5VDC (±10%), ≥ 500mA (supplied adaptor)

Dimensions

4.6 x 4 x 4” (117 x 102 x 102 mm)

Weight

7.2 oz (204 g)

Maintenance

Cleaning and storage

1. The meter should be wiped with a damp cloth and mild detergent when necessary. Do not

use solvents or abrasives.

2. Store the meter in an area with moderate temperature and humidity.

9CO210-en-US v1.3 1/21

Troubleshooting

No power

Check that the AC adaptor is properly connected.

Slow response

Check that rear air flow vents are not blocked.

"BAt” and green LED flash

The adaptor output voltage is too high or too low.

Error Display Codes

CO2

Display

Code

E01

CO2sensor malfunction.

Return for repair.

E02

CO2reading out of range (low).

Re-calibrate the meter. If problems persist,

return for repair.

E03

CO2reading out of range (high).

Place the meter in fresh air and allow 5

minutes. If problem persists, re-calibrate the

meter. Return for service if necessary.

E17

CO2senor failure.

Return for repair.

Temperature

Display Code

E02

Air temperature out of

range (low).

Place the meter at room temperature for 30

minutes. If problem persists, return for repair.

E03

Air temperature out of

range (high).

Same as EO2.

E31

Sensor malfunction.

Return for repair.

Humidity

Display

Code

E04

Temperature display shows error.

Refer to temperature error codes.

E11

RH calibration failure.

Please return for repair.

E34

RH sensor circuit failure.

Please return for repair.

10 CO210-en-US v1.3 1/21

CO2Level Guidelines

Important: The public information provided below is offered for reference only. FLIR Systems, Inc. is not

liable for injury to persons or property through the use or misuse of this device. It is the responsibility of the

user to ensure proper air quality in the residential or commercial spaces where this device is to be used.

Non-enforced reference levels:

•250 - 350 ppm: Normal background outdoor levels.

•350- 1,000 ppm: Typical level found in occupied spaces with good air exchange.

•1,000 –2,000 ppm: Level associated with complaints of drowsiness and poor air.

•2,000 –5,000 ppm: Level associated with headaches, sleepiness, and stagnant, stale, or stuffy air. Poor

concentration, loss of attention, increased heart rate and slight nausea may also be present.

•>5,000 ppm: Exposure may lead to serious oxygen deprivation resulting in permanent brain damage,

coma, and death.

Regulatory exposure limits:

•ASHRAE Standard 62-1989 (1000ppm): CO2concentration in occupied building should not exceed

1000ppm.

•OSHA (5000ppm): Time weighted average over five 8-hour workdays should not exceed 5000ppm.

•Building bulletin 101 (Bb101) 1500ppm: UK standards for schools indicate that CO2, averaged over an

entire day (i.e. 9am to 3:30 pm), should not exceed 1500ppm.

•Germany, Japan, Australia, UK (5000ppm): 8-hour weighted average occupational exposure limit is

5000ppm.

Two-year Warranty

FLIR Systems, Inc. warrants this Extech brand instrument to be free of defects in parts and workmanship for two years from

date of shipment (a six-month limited warranty applies to sensors and cables). To view the full warranty text please visit:

http://www.extech.com/support/warranties.

Calibration and Repair Services

FLIR Systems, Inc. offers calibration and repair services for the Extech brand products we sell. We offer NIST traceable

calibration for most of our products. Contact us for information on calibration and repair availability, refer to the contact

information below. Annual calibrations should be performed to verify meter performance and accuracy. Product specifications

are subject to change without notice. Please visit our website for the most up-to-date product information: www.extech.com.

Contact Customer Support

Customer Support Telephone List: https://support.flir.com/contact

Calibration, Repair, and Returns: repair@extech.com

Technical Support: https://support.flir.com

www.extech.com

Altri manuali per CO210

Indice

Altri manuali Extech Instruments Registratore di dati

Extech Instruments

Extech Instruments 382100 Manuale utente

Extech Instruments

Extech Instruments EA80 Manuale utente

Extech Instruments

Extech Instruments TH10 Manuale utente

Extech Instruments

Extech Instruments RHT20 Manuale utente

Extech Instruments

Extech Instruments 42280-NIST Manuale utente

Extech Instruments

Extech Instruments 451126 Manuale utente

Extech Instruments

Extech Instruments RTH10 Manuale utente

Extech Instruments

Extech Instruments 407780 Manuale utente

Extech Instruments

Extech Instruments CO220 Manuale utente

Extech Instruments

Extech Instruments SD800 Manuale utente

Extech Instruments

Extech Instruments DL150 Manuale utente

Extech Instruments

Extech Instruments 381395 Manuale utente

Extech Instruments

Extech Instruments 475040-SD Manuale utente

Extech Instruments

Extech Instruments 42582 Manuale utente

Extech Instruments

Extech Instruments Quick Start Manuale utente

Extech Instruments

Extech Instruments SD700 Manuale utente

Extech Instruments

Extech Instruments 42280 Manuale utente

Extech Instruments

Extech Instruments 451126 Manuale utente

Extech Instruments

Extech Instruments RHT35 Manuale utente

Extech Instruments

Extech Instruments THD5 Manuale utente

Extech Instruments

Extech Instruments SDL2004 Manuale utente

Extech Instruments

Extech Instruments RTH20 Manuale utente

Extech Instruments

Extech Instruments TM500-NIST Manuale utente

Extech Instruments

Extech Instruments DL160 Manuale utente

Manuali Registratore di dati popolari di altre marche

TESTO

TESTO 176 Manuale utente

HT Italia

HT Italia XL421 Manuale utente

HBM

HBM SOMAT XR CX22B-R Manuale utente

Agtrix

Agtrix 380i Manuale utente

Hobo

Hobo H8 Pro Manuale utente

Beijing ART Tech

Beijing ART Tech PCI2320 Manuale utente

Athena

Athena GET SL1 Manuale utente

Motec Systems

Motec Systems C185 Manuale utente

Beijing ART Tech

Beijing ART Tech USB2832 Manuale utente

Rotronic

Rotronic HygroLog HL20 Manuale utente

MRC

MRC DW-6092 Manuale utente

Racelogic

Racelogic VBOX LapTimer Manuale utente

Edu-Logger

Edu-Logger 900-240 Manuale utente

Elma

Elma DT173 Manuale utente

MadgeTech

MadgeTech PRTemp140 Scheda tecnica

Comet

Comet U0121M Manuale utente

pico Technology

pico Technology PT-104 Manuale utente

Soil Instruments

Soil Instruments GTecLink Manuale utente