Extech Instruments 407119A Manuale utente

POWER

HOLD

ESC

REC.

Enter

UNIT / ZERO FUNCTION

SETUP

AREA

AVERAGE

Ft/min73.2 F

407119A

Hot Wire

Anemometer

CFM

User's Guide

Heavy Duty Hot Wire CFM Thermo-Anemometer

Model 407119A

Model 407119A Version 5.0 October 20052

Warranty

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects

in parts and workmanship for three years from date of shipment (a six month limited

warranty applies to sensors and cables). If it should become necessary to return the

instrument for service during or beyond the warranty period, contact the Customer Service

Department at (781) 890-7440 ext. 210 for authorization or visit our website

www.extech.com for contact information. A Return Authorization (RA) number must be

issued before any product is returned to Extech. The sender is responsible for shipping

charges, freight, insurance and proper packaging to prevent damage in transit. This

warranty does not apply to defects resulting from action of the user such as misuse,

improper wiring, operation outside of specification, improper maintenance or repair, or

unauthorized modification. Extech specifically disclaims any implied warranties or

merchantability or fitness for a specific purpose and will not be liable for any direct, indirect,

incidental or consequential damages. Extech's total liability is limited to repair or

replacement of the product. The warranty set forth above is inclusive and no other

warranty, whether written or oral, is expressed or implied.

Introduction

Congratulations on your purchase of the Extech 407119A Thermo-Anemometer. The

407119A measures air velocity, air volume, and air temperature. It uses a telescoping

probe antenna to allow convenient access to grills and diffusers. Careful use of this

meter will provide years of reliable service. The Model 407119A features are listed

below.

Features

•Combination hot wire probe (for air velocity) and thermistor sensor (for temperature)

deliver rapid and precise measurements even at low air velocity values.

•Slim probe design with telescoping antenna for easy grill and diffuser access

•Air Velocity, Air Volume, and Air Temperature measurements

•20 Reading Average feature

•Zero adjustment

•Data Hold and Record/Recall Max/Min features

•Auto Power OFF

•PC Interface (RS-232) with optional software and cable for data acquisition

Applications

Environmental testing, air conveyors, flow hoods, clean rooms, air balancing,

fans/motors/blowers, furnace velocity, paint spray booths, and others.

Model 407119A Version 5.0 October 20053

Specifications

General Specifications

Display Dual function 5-digit LCD

Measurement units Air Velocity: m/s, km/h, ft/min, knots, mph;

Air Flow: CMM (m3/min) and CFM (ft3/min);Temperature: °C and °F

Data hold Freezes displayed reading

Sampling rate Display update rate:1 second (approx.)

Sensors Air velocity and temperature sensors: Thermistor type

MAX/MIN Memory Record and view Maximum and Minimum readings

Average feature Averages up to 20 readings

Automatic Power off Auto shut off after 15 minutes

Data Output RS-232 PC serial interface with 16-bit data stream output

Operating Temp. 32 to 122°F (0 to 50°C)

Operating Humidity Max. 80% Relative Humidity

Power Supply Four (4) ‘AA’ 1.5V batteries or optional AC adaptor

Power Current 70mA DC (approx.)

Weight (meter only) 1.15 lbs. (521g) with batteries installed

Dimensions Main instrument: 7.9 x 3.0 x 1.5" (200.0 x 76.2 x 36.8mm)

Telescoping Sensor: 0.5" (12.7mm) diameter head

Min length of sensor: 8” (260mm); Max. length: 37” (0.94m) with 5.5’

(1.7m) cable

Range Specifications

Air Velocity Range Resolution Accuracy (of rdg)

m/s (meters per second) 0.2 – 17.0 m/s 0.1 ±(5% + 5 digits)

km/h (kilometers per hour) 0.7 – 61.2 km/h 0.1 ±(5% + 20 digits)

ft/min (feet per minute) 40 – 3346 ft/min 1 ±(5% + 100 digits)

mph (miles per hour) 0.5 – 38.0 mph 0.1 ±(5% + 10 digits)

knots (nautical miles per hour) 0.4 to 33.0 knots 0.1 ±(5% + 10 digits)

Air Flow Measurements Range Resolution Area Range

CMM (cubic meters per min.) 0 – 36,000 m3/min 0.001 to 1 0.001 to 30.0 m2

CFM (cubic feet per minute) 0 – 1,271,200 ft3/min 0.01 to 100 0.01 to 322.91ft2

Range Resolution AccuracyAir Temperature

32 to 122oF

(0 to 50oC) 0.1oF/C ±1.5oF (0.8oC)

Model 407119A Version 5.0 October 20054

Meter Description

1. Display

2. POWER button

3. HOLD and ESC button

4. REC and ENTER button

5. UNIT, ZERO, and ▲up arrow button

6. Function and ▼down arrow button

7. AVG. START, CLEAR, and ►right arrow button

8. AREA SET button

9. Tilt stand

10. Battery compartment / Cover

11. Tripod mount

12. LCD contrast adjustment pot

13. System reset switch

14. RS-232 Output terminal

15. DC9V power adaptor

15 14 13 12

Model 407119A Version 5.0 October 20055

Operation

Initialization and Zero procedures (please follow these steps before use)

Important Note: The meter’s probe locking switch must

be in the locked position (with the probe inserted) for

the meter to turn on and operate correctly. Refer to the

accompanying diagram or the diagram at the top of the

meter for switch orientation.

For the best accuracy and for proper operation, the

following steps must be performed.

1. Connect the sensor to the input jack on top of the

meter by first unlocking the sensor jack and then

inserting the sensor plug. Lock the sensor jack after

the probe is inserted.

2. Press the POWER button to turn on the meter. The meter will perform a self-test during

which the display will count down from 9999 to 0000.

3. Select the air velocity function using the FUNCTION button. The LCD will display the

most recently selected unit of measure for air velocity.

4. To change the temperature units of measure (C/F), use the advanced programming

mode discussed later in this manual.

5. Momentary presses of the UNIT button changes the air velocity units. The LCD will

reflect the selection.

6. Place the sensor cover in the up (ZERO) position (see diagram below).

7. Open the telescoping sensing antenna to a convenient length.

8. Place the sensor in the area to be measured and allow a short time for it to stabilize to

the ambient temperature.

9. To Zero the meter display, press and hold the ZERO button until the second beep.

Warning! Do not touch the air velocity or temperature thermistors inside the sensor head

while moving the sensor cover.

TOP VIEW OF METER

LOCKED Position

UNLOCKED Position

Model 407119A Version 5.0 October 20056

Air Velocity Measurements

1. Follow the Initialization and Zeroing procedures above before continuing.

2. Open the antenna to the desired length.

3. Slide the air velocity sensor cover down.

4. Press the POWER button to turn the meter on.

5. Place the sensor in the air

current to be measured.

Have the air flow meet the

sensor head in the

direction of the white dot

(as shown in diagram).

6. View the air velocity and temperature readings on the LCD Display. The large main

LCD display shows the Air Velocity reading. The lower LCD sub-display shows the

temperature reading (left) and the unit of measure (right).

7. To turn the meter off, press and hold the POWER button until the meter switches off.

Air Flow (Volume) Measurements (CMM / CFM)

NOTE: Temperature is not displayed while the meter is in the Air Flow mode.

1. Follow the steps in the Initialization and Zeroing section before continuing.

2. Select the air flow mode using the Function button. The LCD will display CMM (cubic

meters per minute) or CFM (cubic feet per minute) when Air Flow is selected.

3. Press the UNIT button momentarily to select the desired air flow units: CMM or CFM.

The LCD display will reflect the selection.

4. Calculate the area of the duct or vent under test (refer to the Useful Conversions and

Equations section in the back of this manual for assistance). Be sure to compute the

area of the vent or duct in square feet or meters. If you have the area in inches, convert

inches to feet before programming the meter with the area value.

5. Press the AREA SET button to begin entering the area in m2or ft2. The left digit will

begin flashing. Follow the steps below to enter the area of the duct or vent in question:

Use the ►button to select a digit to change (digit will flash)

Use the ▲button increase the value of the flashing digit

Use the ▼button to decrease the value of the flashing digit

6. Press the REC/Enter button and then the AREA SET button to save the new area

value

7. After the area has been entered, the new area value will be shown on the lower left of

the LCD display in ft2or m2. If the unit of measure is CFM, the area will be shown in

square feet. If the unit of measure is CMM, the area will be shown in meters squared.

8. Press the ESC button to abort the programming at any time.

9. Place the probe in the area under test. The main LCD digits will indicate the air flow in

CFM or CMM. If the CFM or CMM reading exceeds 99999, use the displayed X10

multiplier to calculate the reading.

10. To turn the meter off, press and hold the POWER button until the meter switches off.

Model 407119A Version 5.0 October 20057

AVERAGE Feature for the Air Flow Mode

In the Average mode, up to 20 readings can be stored and averaged.

1. In the Air Flow Mode (discussed earlier), press the FUNCTION button momentarily

until the AVG icon and a ‘zero’ appears on the lower LCD display line.

2. Press the AVG START button to record the current reading. A ‘1’ will appear on the

lower LCD line indicating that one reading has been stored.

3. Press the AVG START for up to a total of 20 measurements. The number on the lower

LCD line will increment with each press of the AVG START button letting the user

know how many readings are currently being averaged. Note that only the averaged

reading is shown while in this mode, not the actual reading.

4. To clear (erase) all of the currently stored readings and start again, press and hold the

AVG button until the meter beeps twice. Note that the counter resets to ‘0’ and that the

meter is ready to start another averaging session.

5. Use the FUNCTION button to exit this mode of operation.

Data Hold Feature

1. While taking measurements, press the HOLD button to freeze a reading.

2. The HOLD indicator will appear on the LCD when the display is in Data Hold mode.

3. Press HOLD again to return to normal operation.

Maximum (MAX) and Minimum (MIN) Recording

The MAX / MIN Record-Recall feature allows the user to record and view the highest and

lowest readings during a measurement session.

1. Press the REC button once. The REC indicator will appear on the display and the

meter will begin keeping track of the MAX and MIN values.

2. To view the MAX reading, press REC again. The MAX indicator along with the

maximum reading will appear on the LCD display.

3. Press REC again to view the minimum value, the MIN indicator along with the

minimum reading will appear on the LCD display.

4. To return to normal operation, press and hold the REC button for approx. 3 seconds

(until the meter beeps). The display indicators REC, MAX, and MIN will disappear.

Note: Auto Power Off is disabled in the RECORD mode.

Auto Power Off

To save battery life, the meter will automatically shut off after approximately 15 minutes of

operation. To temporarily disable this feature (until the meter’s power is cycled), press the

REC button and enter the RECORD mode. Alternatively, go to the advanced programming

section (later in this manual) for instructions on how to disable it long term.

Model 407119A Version 5.0 October 20058

Advance Programming Mode

From the Air Velocity mode of operation, press and hold the SET button until the meter

beeps and a ‘1’ is displayed. The advanced programming mode is now accessed. The

Auto Power OFF Enable/Disable and the Temperature Units selections are available in the

advanced programming mode. Use the ESC button to exit this mode at any time.

Auto Power Enable/Disable

The first parameter in the advanced mode is the Auto Power OFF enable/disable. Use the

up and down arrow keys to select the desired value. ‘0’ defeats the Auto Power OFF

feature; ‘1’ enables the Auto Power OFF feature. Momentarily press the SET button to

move to the next parameter temperature units (see below).

Temperature Units selection (C/F)

The second parameter in the advanced mode is the Temperature Units selection. Use the

up and down arrow keys to select the desired value. ‘0’ selects degrees ‘C’; ‘1’ selects

degrees ‘F’. Press the ESC button to exit the advanced programming mode.

System Reset

If the meter’s display ‘locks up’ and/or the button presses do not cause the display to

change, try a system reset. To reset the meter, use one of the following methods.

1. Move the probe lock switch from the ON to the OFF to the ON position again. Turn the

meter on.

2. While powering the meter, press the RESET switch (side compartment) using the point

of a paper clip.

Model 407119A Version 5.0 October 20059

PC Interface

The 407119A is equipped with a 3.5mm jack (side compartment) for connection to a PC for

data acquisition purposes. The meter’s data output is a 16 bit data stream. To obtain PC

interface cabling and WindowsTM data acquisition software, contact Extech Instruments.

Instructions for use are provided with the software. The PC interface cable schematic, data

stream protocol, and RS-232 communication settings are provided below.

PC Interface Cable schematic

Protocol for 16-bit data stream

D0 End Word = ‘0D’

D1 & D8 Displayed reading; D1 = LSD; D8 = MSD. For example,

For a displayed reading of 1234, D8 through D1 is 00001234

D9 Decimal point (right to left):

0 = no decimal; 1 = 1 place; 2 = 2 places; 3 = 3 places

D10 Polarity: 0 = positive; 1 = negative

D11 & D12 Displayed unit of measure: 01 = oC; 02 = oF; 08 = m/s; 09 = knots;

10 = km/hr; 11 = ft/min; 12 = MPH; 84 = CMM; 85 = CFM;

0A = Square meter (area); 0B = Square feet (area)

D13 1 = Upper LCD display digits; 2 = Lower LCD display digits

D14 Always ‘4’

D15 Start word ‘02’

RS-232 Settings

Baud rate: 9600

Parity: No parity

Data bits: 8

Stop bits: 1

Meter

3.5mm jack

Center pin.............................Pin 4

Ground / Shield.....................Pin 2

DB-9 pin

Pin 5

2.2K

Resistor

Model 407119A Version 5.0 October 200510



Support line (781) 890-7440

Technical support: Extension 200; E-mail: support@extech.com

Repair & Returns: Extension 210; E-mail: [email protected]

Product specifications subject to change without notice

For the latest version of this User’s Guide, Software updates,and other

up-to-the-minute product information, visit our website: www.extech.com

Extech Instruments Corporation,285 Bear Hill Rd., Waltham, MA 02451

Battery Replacement

When the battery icon appears on the lower left corner of the LCD display, the four (4) ‘AA’

batteries must be replaced.

1. Remove the rear Phillips head screw

2. Slide off the rear battery compartment

3. Replace the batteries

4. Secure the battery compartment

Calibration and Repair Services

Extech offers repair and calibration services for the products we sell. Extech also

provides NIST certification for most products. Call the Customer Service Department for

information on calibration services available for this product. Extech recommends that

annual calibrations be performed to verify meter performance and accuracy.

Altri manuali per 407119A

Indice

Altri manuali Extech Instruments Multimetro

Extech Instruments

Extech Instruments SDL350 Manuale utente

Extech Instruments

Extech Instruments 407227 Manuale utente

Extech Instruments

Extech Instruments EN300 Manuale utente

Extech Instruments

Extech Instruments TK505 Manuale utente

Extech Instruments

Extech Instruments MiniTec Series Manuale utente

Extech Instruments

Extech Instruments EX310 Manuale utente

Extech Instruments

Extech Instruments EX430-NIST Manuale utente

Extech Instruments

Extech Instruments 38070 Manuale utente

Extech Instruments

Extech Instruments 380941 Manuale utente

Extech Instruments

Extech Instruments SD750 Manuale utente

Extech Instruments

Extech Instruments AUT500 Manuale utente

Extech Instruments

Extech Instruments 38394 Manuale utente

Extech Instruments

Extech Instruments 382065 Manuale utente

Extech Instruments

Extech Instruments DM220 Manuale utente

Extech Instruments

Extech Instruments RC200 Manuale utente

Extech Instruments

Extech Instruments EX430A Manuale utente

Extech Instruments

Extech Instruments MultiTec MT310 Manuale utente

Extech Instruments

Extech Instruments Extech 470 Manuale utente

Extech Instruments

Extech Instruments MP510A Manuale utente

Extech Instruments

Extech Instruments 38390 Manuale utente

Extech Instruments

Extech Instruments MultiLog ML720 Manuale utente

Extech Instruments

Extech Instruments 380947 Manuale utente

Extech Instruments

Extech Instruments MN26-NIST Manuale utente

Extech Instruments

Extech Instruments EX330 Manuale utente

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Fluke

Fluke 83 Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Mastech

Mastech MY70 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Fluke

Fluke 8846A Manuale operativo e di manutenzione

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

Mastech

Mastech MS8238C Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente