Extech Instruments 42529 Manuale utente
User’s Manual
InfraRed Thermometer
with Laser Pointer
MODEL 42529
Introduction
Congratulations on your purchase of the Model 42529 IR Thermometer. This thermometer
makes non-contact (infrared) temperature measurements at the touch of a button. The
built-in laser pointer increases target accuracy while the backlit LCD and handy push-
buttons combine for convenient, ergonomic operation. Proper use and care of this meter
will provide years of reliable service.
Model 42529-EU V2.0 5/09
2
1
2
3
4
5
6
Safety
Use extreme caution when the laser pointer beam is on
Do not point the beam toward anyone's eye or allow the
beam to strike the eye from a reflective surface
Do not use the laser near explosive gases or in other
potentially explosive areas
Specifications
Infrared Thermometer Specifications
Range / Resolution -20 to 320oC (0 to 600oF) 1oC/F
Accuracy ± 2% of reading or ± 2oC (4oF) whichever is greater.
Note: Accuracy is specified for the following ambient
temperature range: 18 to 28°C (64 to 82°F)
Emissivity 0.95 fixed value
Field of View D/S = Approx. 6:1 ratio (D = distance, S = spot)
Laser power Less than 1mW
Spectral response 6 to 14 m (wavelength)
General Specifications
Display 3½ digit backlit LCD display with function indicators
Display rate 1 second approx.
Over range indication Audible tone sounds and ‘OVER’ appears on the LCD when
the measurement exceeds the measurement range spec.
Operating Temperature 0°C to 50°C (32°F to 122°F)
Operating Humidity Max. 80% RH.
Power Supply 9V battery
Automatic Power Off Meter shuts off automatically after 7 seconds
Weight 180g / 6.35 oz.
Size 211 x 89 x 38mm (8.3 x 3.5 x 1.5”)
Meter Description
1. LCD Display
2. Function Buttons
3. Handle Grip
4. Laser Pointer
5. IR Sensor
6. Measurement Trigger
7. Battery Compartment
Model 42529-EU V2.0 5/09
3
Operating Instructions
1. Hold the meter by its Handle Grip and point it toward the device whose temperature is
to be measured.
2. Press and hold the red Trigger to turn the meter on and begin testing. The display will
light if the battery is charged. Replace the battery if the display does not light.
3. While continuing to press the Trigger, push the red Laser button to turn on the laser
pointer. Aim the red beam approximately a half inch higher than the point of test as
shown in the diagram below (pressing the Laser button again turns the laser off).
4. While measuring, the SCAN display icon will appear on the LCD above the
temperature measurement and to the left of the emissivity value (fixed at 0.95.).
5. If the measurement exceeds the useable temperature range (0 to 600oF), the meter will
emit a tone and the LCD will display ‘OVER’.
6. Release the Trigger when the temperature stabilizes. The HOLD display icon will
appear on the LCD indicating that the reading is being held.
7. Set the temperature units (oC or oF) using the blue oCand oFbuttons.
8. Press the yellow Backlight key to turn on the LCD backlighting function.
9. The meter will automatically power down after 7 seconds.
Field of View
The meter’s field of view is 6:1. For example, if the meter is 30.4cm from the target (spot),
the diameter of the target must be at least 5.08cm. Other distances are shown below in the
field of view diagram.
Note that measurements should normally be made less than 60.9cm from the target. The
meter can measure from further distances but the measurement may be affected by
external sources of light. In addition, the spot size may be so large that it encompasses
surface areas not intended to be measured.
Model 42529-EU V2.0 5/09
4
Measurement Notes
1. The object under test should be larger than the spot (target) size calculated by the field
of view diagram (see diagram on previous page or on side of the meter).
2. If the surface of the object under test is covered with frost, oil, grime, etc., clean before
taking measurements.
3. If an object's surface is highly reflective apply masking tape or flat black paint before
measuring.
4. The meter cannot measure through transparent surfaces such as glass.
5. Steam, dust, smoke, etc. can obscure accurate measurements.
6. The meter compensates for deviations in ambient temperature. It can, however, take
up to 30 minutes for the meter to adjust to extremely wide ambient temperature
changes.
7. To find a hot spot, aim the meter outside the area of interest then scan across (in an up
and down motion) until the hot spot is located.
Battery Replacement
When the low battery symbol appears on the LCD, replace the meter’s 9V battery.
The battery compartment is located on the bottom of the meter's handle. Open the
compartment by sliding the battery compartment cover off in the direction of the arrow.
Replace battery and re-install the battery compartment cover.
You, as the end user, are legally bound (Battery ordinance) to return all used
batteries and accumulators; disposal in the household garbage is prohibited!
You can hand over your used batteries / accumulators at collection points in your
community or wherever batteries / accumulators are sold!
Disposal: Follow the valid legal stipulations in respect of the disposal of the
device at the end of its lifecycle
Copyright ©2005 Extech Instruments Corporation
All rights reserved including the right of reproduction in whole or in part in any form.
Altri manuali Extech Instruments Termometro
Extech Instruments
Extech Instruments 39240 Manuale utente
Extech Instruments
Extech Instruments 42545-NIST Manuale utente
Extech Instruments
Extech Instruments RH250W Manuale utente
Extech Instruments
Extech Instruments TM55 Manuale utente
Extech Instruments
Extech Instruments RH401 Manuale utente
Extech Instruments
Extech Instruments RH490-NIST Manuale utente
Extech Instruments
Extech Instruments 42545 Manuale utente
Extech Instruments
Extech Instruments SD200 Manuale utente
Extech Instruments
Extech Instruments 42570 Manuale utente
Extech Instruments
Extech Instruments IR100 Manuale utente
Extech Instruments
Extech Instruments 42545 Manuale utente
Extech Instruments
Extech Instruments EA10-NIST Manuale utente
Extech Instruments
Extech Instruments TM100 Manuale utente
Extech Instruments
Extech Instruments 433201 Manuale utente
Extech Instruments
Extech Instruments AN500 Manuale utente
Extech Instruments
Extech Instruments VIR50-NISTL Manuale utente
Extech Instruments
Extech Instruments 42515 Manuale utente
Extech Instruments
Extech Instruments EA15 Manuale utente
Extech Instruments
Extech Instruments 42512 Manuale utente
Extech Instruments
Extech Instruments HD500 Manuale utente
