Extron electronics DTP3 T 202 Manuale utente

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

DTP3T 202/DTP3 R 201 • Setup Guide

The DTP3 T 202 transmitters and DTP3 R 201 receivers can extend HDMI digital video signal with resolutions up to 4K@60Hz

(4:4:4), digital embedded audio, bidirectional RS‑232 control, and remote power up to 330feet (100meters), using shielded

twisted pair cabling as a transmission medium. This guide provides quick start instructions for an experienced installer to set up

and operate these DTP3 digital video extenders.

NOTE: Maximum transmission distances will vary with resolutions used, cable types, and environment (see the

DTP3T202/DTP3R201UserGuide at http://www.extron.com for full specifications).

DTP3 R 201

CONFIG

SEND

PWR

OFF

SIGNAL

HDCP

INPUT

POWER

12V

1.5A MAX

OVER

DTP3

RS-232

RxTx

LINK

DTP3 IN

SIG

HDMI

AUDIO OUT

OUTPUT

DTP3 T 202

CONFIG

INPUT

HDBT

DTP

SIGNAL

HDCP

SEND

PWR

OFF

POWER

12V

1.5A MAX

OVER

RS-232

RxTx

LINK

OUT

SIG

HDMI

LOOP OUT

HDMI

INPUT

POWER

12V

0.3A MAX

IPL PRO S3

Tx Rx RTSCTS G

Tx Rx RTS CTS G

Tx Rx RTSCTS

COM 1COM 2COM 3

LAN / PoE

RS-232 RS-232

HDMI

CATx Cable up to 330' (100 m)

4K HDR DisplayPC with Local 4K Monitor

Extron

P3 T 202

ransmitter

Extron

IPL Pro S3

IP Link Pro

Control Processor

Extron

DTP3 R 201

Receiver

Figure 1. Typical Transmitter and Receiver Application

Installation

Turn off and disconnect all equipment power sources and mount the transmitter and receiver units as required. The transmitter

and receiver can be securely mounted in a variety of locations, using optional Extron Mounting Brackets and accessories (see

http://www.extron.com to determine which optional mounting accessories are compatible).

Rear Panel Connections

DTP3 T 202

CONFIG

INPUT

HDBT

DTP

SIGNAL

HDCP

SEND

PWR

OFF

POWER

12V

1.5A MAX

OVER

RS-232

RxTx

LINK

OUT

SIG

HDMI

LOOP OUT

HDMI

INPUT

DTP3 R 201

CONFIG

SEND

PWR

OFF

SIGNAL

HDCP

INPUT

POWER

12V

1.5A MAX

OVER

DTP3

RS-232

RxTx

LINK

DTP3 IN

SIG

HDMI

AUDIO OUT

OUTPUT

DTP3 T 202 Front Panel DTP3 R 201 Front Panel

DTP3 T 202 Rear Panel DTP3 R 201 Rear Panel

A B C ED A B C E

A B EDC A F ED G

Figure 2. Rear Panels of the DTP3 T 202 and DTP3 R 201

APower inlet — Connect an IEC power cord between the included 12VDC, 2.0A power supply and a 100‑240VAC, 50‑60Hz

source. Connect the supply to either unit to power both units (see figure 3 on the next page to wire the power connector).

ATTENTION:

• Do not connect any external power supplies until you have read the Attention notications in the Power Supply

section of the DTP3T202/DTP3R201UserGuide.

• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section « Power

Supply » du DTP3T202/DTP3R201UserGuide.

figure 1

figure 2

DTP3T 202/DTP3 R 201 • Setup Guide (Continued)

NOTE: One power supply is included with the transmitter and normally can power both units, if they are both from the

Extron DTP3 series.

SECTION A–A

Ridges

Smooth

3/16"

(5 mm) Max.

POWER

12V

--A MAX

Figure 3. Power Wiring Diagram

BLoop Out port (Tx) — Connect a display with an HDMI input to display the Input signal to the transmitter.

CHDMI Input (Tx) — Connect an HDMI cable between this port and the digital video source.

NOTE: See the LockIt™ Lacing Brackets on the next page to securely fasten HDMI connectors.

DDTP3 RJ‑45 ports — Connect transmitter OUT to receiver DTP3 IN, using a twisted pair cable. Extron recommends using

the following practices to achieve full transmission distances and reduce transmission errors:

• Use Extron XTP DTP 22 STP cable for the best performance. At minimum, Extron recommends 22 AWG, solid

conductor, STP cable with a minimum bandwidth of 500 MHz.

• Terminate cables with sheilded connectors to the TIA/EIA‑T568B standard (see image below).

• Limit the use of more than two pass‑through points, which may include patch points, and punch down connectors. If

these pass‑through points are required, use shielded couplers and punch down connectors.

ATTENTION:

• Do not connect these devices to a telecommunications or computer data network.

• Ne connectez pas ces appareils à un réseau de télécommunications ou de données

informatiques.

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA T

568 B

TP Wires

12345678

Pins:

NOTE: When using shielded twisted pair cable in bundles or conduits, consider the

following:

• Do not exceed 40% ll capacity in conduits.

• Do not comb the cable for the rst 20 meters, where cables are straightened, aligned,

and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook‑and‑loop fasteners.

• Seperate twisted pair cables from AC power cables.

ERS‑232 ports — To pass serial or control signals, connect the host device to the transmitter and the peripheral device to

the receiver via the RS‑232 captive screw connectors on both units

(see figure 4 for wiring).

RS-232

Tx Rx

RS-232

Transmit (Tx)

Receive (Rx)

Ground(Gnd)

RS-232 Device Bidirectional

Transmit (Tx)

Receive (Rx)

Ground(Gnd)

Figure 4. RS‑232 Wiring Diagram

FHDMI Output (Rx) — Connect a display with an HDMI input to view the transmitted digital image.

GAudio Output (Rx) — Connect a balanced or unbalanced audio device, such as an audio amplifier or powered speakers, to

the receiver via the audio captive screw connector (see figure 5 to wire analog audio output).

Do not tin

the wires!

Balanced Audio Output

Tip

Ring

Tip

Ring

Slee

ves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

Figure 5. Balanced and Unbalanced Audio Output Wiring Diagram

figure 3

figure 4

figure 5

ATTENTION:

• For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (–)

contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux

contacts négatifs (–).

LockIt™ Lacing Brackets

Use an included LockIt lacing bracket to securely fasten an HDMI cable to each device as

follows:

1Plug the HDMI cable into the panel connection.

2Loosen the HDMI connection mounting screw from the panel enough to allow the

LockIt lacing bracket to be placed over it. The screw does not have to be removed.

3Place the LockIt lacing bracket on the screw and against the HDMI connector, then

tighten the screw to secure the bracket.

ATTENTION:

• Do not overtighten the HDMI connector mounting screw. The shield it

fastens to is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage

auquel elle est attachée est très n et peut facilement être dénudé.

4Loosely place the included tie wrap around the HDMI connector and the LockIt lacing

bracket as shown.

5While holding the connector securely against the lacing bracket, use pliers to tighten

the tie wrap, then remove any excess length.

Front Panel Features

DTP3 T 202

CONFIG

INPUT

HDBT

DTP

SIGNAL

HDCP

SEND

PWR

OFF

POWER

12V

1.5A MAX

OVER

RS-232

RxTx

LINK

OUT

SIG

HDMI

LOOP OUT

HDMI

INPUT

DTP3 R 201

CONFIG

SEND

PWR

OFF

SIGNAL

HDCP

INPUT

POWER

12V

1.5A MAX

OVER

DTP3

RS-232

RxTx

LINK

DTP3 IN

SIG

HDMI

AUDIO OUT

OUTPUT

DTP3 T 202 Front Panel DTP3 R 201 Front Panel

DTP3 T 202 Rear Panel DTP3 R 201 Rear Panel

A B C ED A B C E

A B EDC A F ED G

Figure 6. Front Panels of the DTP3 T 202 and DTP3 R 201

APower LED — Lights green when the unit is receiving power, either locally or remotely (on the DTP cable).

BConfiguration port — Using a USB cable, connect a PC to this front panel USB C port for remote operation using PCS and

firmware updates.

CSend Power toggle switch — In a DTP3 transmitter to DTP3 receiver configuration, set the toggle switch to the UP

(SEND PWR) position on the powered DTP3 device to enable sending remote power to a DTP3 device on the far end. Set

the toggle switch to the DOWN (OFF) position on the DTP3 device receiving power (see figure 7 on the next page for toggle

switch configuration).

ATTENTION:

• The DTP3 T 202 and DTP3 R 201 devices are congured to output power to DTP3 models only. If connected to a

non‑DTP3 device, set the toggle switch to the DOWN (OFF) position. Failure to turn the power OFF will damage the

connected device.

• Le DTP3 T 202 et le DTP3 R 201 sont congurés pour alimenter uniquement les modèles DTP3. S’ils sont connectés

à un autre type d’appareil, veuillez positionner l’interrupteur à bascule sur « DOWN » (OFF). Si l’interrupteur n’est

pas positionné sur OFF, vous risquez d’entraîner la défaillance de l’appareil non DTP3 connecté.

DHDBT/DTP toggle switch (Tx) — Configures the DTP3 Output for either HDBT or DTP mode.

figure 6

68-3445-50 Rev. C

07 21

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

EFront panel indicators

• SIGNAL — Lights when the unit is receiving a TMDS clock signal on the Input connector (transmitter), or any valid

signal on the DTP3 IN connector (receiver).

• HDCP — Lights when the unit is receiving an HDCP‑compliant signal on the Input connector (transmitter) or on the

DTP3 IN connector (receiver).

SEND

POWER

OFF

SEND

POWER

OFF

SEND

POWER

OFF

SEND

POWER

OFF

SEND

POWER

OFF

SEND

POWER

OFF

DTP HDMI 330 Rx

OVER DTP

RS-232 IR

Tx Rx Tx RxG

OFF

OFF ON

ON OFF

DTP HDMI 330 Tx DTP3 R 201

CONFIG

SEND

PWR

OFF

SIGNAL

HDCP

INPUT

DTP3 R 201

CONFIG

SEND

PWR

OFF

SIGNAL

HDCP

INPUT

DTP3 R 201

CONFIG

SEND

PWR

OFF

SIGNAL

HDCP

INPUT

DTP3 T 202

CONFIG

INPUT

HDBT

DTP

SIGNAL

HDCP

SEND

PWR

OFF

DTP3 T 202

CONFIG

INPUT

HDBT

DTP

SIGNAL

HDCP

SEND

PWR

OFF

DTP3 T 202

CONFIG

INPUT

HDBT

DTP

SIGNAL

HDCP

SEND

PWR

OFF

CATx Cable

up to 330' (100 m)

No Remote Power

Local

Power Supply

Local

Power Supply

Local

Power Supply

CATx Cable

up to 330' (100 m)

Local

Power Supply

Extron

DTP3 R 201

Receiver

No Remote Power

Extron

DTP3 T 202

Transmitter

Extron

DTP HDMI 4K 330 Rx

Receiver

DTP Endpoint Connected to a DTP3 Endpoint

CATx Cable

up to 330' (100 m)

Direction of

Remote Power

Local

Power Supply

Extron

DTP3 T 202

Transmitter

Extron

DTP3 R 201

Receiver

CATx Cable

up to 330' (100 m)

Direction of

Remote Power

Extron

DTP3 T 202

Transmitter

Extron

DTP3 R 201

Receiver

DTP3 Endpoint Connected to a DTP3 Endpoint

Local

Power Supply

Extron

DTP HDMI 4K 330 Tx

Transmitter

Figure 7. Send Power Toggle Switch Conﬁguration

figure 7

Altri manuali per DTP3 T 202

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extron electronics Hardware per computer

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Manuale utente

Extron electronics

Extron electronics PIP 422 Manuale utente

Extron electronics

Extron electronics Annotator 300 Manuale utente

Extron electronics

Extron electronics DMP 44 LC Manuale utente

Extron electronics

Extron electronics DTP3 T 202 Manuale utente

Extron electronics

Extron electronics Quantum Ultra Manuale utente

Extron electronics

Extron electronics Dual Window Multi-Graphic Processor MGP 462 Manuale utente

Extron electronics

Extron electronics IPL M PDP-ES Istruzioni per l'installazione e il funzionamento

Extron electronics

Extron electronics Annotator 300 Manuale utente

Extron electronics

Extron electronics DVI Output Card Manuale utente

Extron electronics

Extron electronics XMP 240 C AT Manuale utente

Extron electronics

Extron electronics Network Device PIP 444 Manuale utente

Extron electronics

Extron electronics SC 210 Manuale utente

Extron electronics

Extron electronics DMP 128 FlexPlus Manuale utente

Extron electronics

Extron electronics MTP 15HD RS Series Manuale utente

Extron electronics

Extron electronics UCS 601 Manuale utente

Extron electronics

Extron electronics Annotator 401 Manuale utente

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Manuale utente

Extron electronics

Extron electronics DTP3 T/R 301 Manuale utente

Extron electronics

Extron electronics AXP 64 C AT Manuale utente

Extron electronics

Extron electronics EDID 101H 4K PLUS Manuale utente

Extron electronics

Extron electronics Quantum Ultra Series Manuale utente

Extron electronics

Extron electronics IPL Pro S1 Manuale utente

Extron electronics

Extron electronics IPCP Pro PCS1 xi Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente