Extron electronics CrossPoint 300 Series Manuale utente

HomeLogic LLC 100 Hoods Lane Marblehead, MA 09145 Phone (781) 639-5155 Fax (781) 639-9677

OneHome



Audio Integration Note

Manufacturer: Extron Electronics

Model Number(s): CrossPoint 300 Series Matrix Switchers

Comments:

Document Revision Date: 9/5/06

VERVIEW AND

UPPORTED

EATURES

THE FOLLOWING FEATURES ARE SUPPORTED:

Traditional Matrix Switcher: The CrossPoint 300 switches are multizone - multisource audio / video

switchers that can be controlled by the OneHome software using an RS-232 port. The OneHome Viewer

interface can be used to select sources in each zone.

Standard Configurations: The CrossPoint series driver will switch audio and video to a zone together. In

other words, if zone 1 is playing Audio Source 2, then Video Source 2 will also be routed to zone 1.

THE FOLLOWING FEATURES ARE NOT SUPPORTED:

Independent Audio / Video Switching: The CrossPoint series switches generally allow you to send

Audio Source 1 to zone 2, and Video Source 1 to zone 3. This is not supported in the OneHome

system: Audio Source 1 and Video Source 1 will switch together.

Volume Control: Volume control is currently not supported for the CrossPoint series: in typical

configurations to date there is a receiver or other amplifier which performs this function. Please contact us

if you would like to have volume control.

NSTALLATION

VERVIEW

1. During the rough-in phase, install wires for the sources, amplifiers and displays for each zone.

2. Also during the rough-in phase, run a Cat5 wire from the location of the switch back to the Network

Assembly of the OneHome system for RS-232 communications. Refer to the RS-232 Connection

Options Integration Note for other options.

3. Install the switch, the sources, amplifier, displays and speakers.

4. Setup the switch to operate according to Extron standard procedures: see Extron Configuration

below.

5. Confirm proper audio and video switching as configured in step above.

6. Connect the OneHome system to the switch electrically. See the wiring diagrams for more

information.

7. Configure the OneHome system for the switch and confirm communication between the switch and

the HomeBrick.

8. Test the system by changing sources in a zone to confirm the correct source plays and volume is

controlled. Test source control for any sources that are to be controlled from the OneHome interface.

2 of 5

XTRON

ONFIGURATION

The CrossPoint switch must be set to 9600 baud, RS-232C (see page 3-35 of the Extron manual):

1. Using the front panel of the switch, press and hold all control buttons to enter Serial Port Configuration

mode.

2. While holding the buttons, the Control and I/O LEDs will turn on, with one in each group flashing.

3. Press and release the Enter button to set 9600 baud.

4. Press and release the RGBHV button to select RS-232.

5. Press and release an input or output button to exit serial port configuration.

6. Wait at least 5 minutes before removing power, or the settings may be lost.

As mentioned above, refer to the Extron documentation for further details.

3 of 5

ONNECTION

IAGRAMS

BILL OF MATERIALS

# Device Manufacturer Part Number Protocol Connector Type Notes

1 DB9M to RJ45 Adapter HomeLogic HA-CB-307 RS-232 DB-9 Male X RJ-45 Female

2 Cat5 Cable Assy. Installer N/A RS-232 RJ-45 Male X RJ-45 Male Must connect all 8 wires

3 Network Assembly HomeLogic HW-NA-18X4 RS-232 RJ-45 Female X DB-9 Female / USB

4 HomeBrick HomeLogic HW-HB-1080 RS-232 DB9 Male / USB

4 of 5

OME

OGIC

ONFIGURATION

ETAILS

The following table provides settings used in the HomeLogic Configurator. Please refer to the Configurator Reference Guide for more details.

In the table below:

o“<Select>” Select the appropriate item from the list (or drop-down) in the Configurator.

o“<User Defined>”, etc. Type in the desired name for the item.

Devices Variable Name Setting Comments

Communication Devices Name

<User Defined> (Default:

Extron System

)

Type Serial Port

Communication Type Standard Connection

Location <User Defined> (Not Required)

Com Port <Select>

Other Audio Devices / Interfaces Name <User Defined> Add Interfaces for any source that does not have a built-in interface

Template <Select>

Default Device <Select> Select the RS-232 or IR controlled source for this interface

Audio Zone Controllers Name

<User Defined> (Default:

Extron CrossPoint 300 88HVA

)

Device Type Extron CrossPoint 300 88HVA

Location <User Defined> (Not Required)

Comm Device

<Select> (Default:

Extron System

)

Sources Name <User Defined>

Source Device <Select> Sources must be previously configured in order to allow selection.

Source Volume <Select> (See Note 1)

Show Source <Select>

Set to

for any inputs that are not used

Source Icon <Select> This icon appears on the source button in the Viewer Interface

Display Name <User Defined> This text appears on the source button in the Viewer Interface

Zones Name <User Defined>

Display <N/A>

Universal Receiver <Select>

Configuration Interface <Select>

Tab Layout Interface Tabs <Select> Move any unused zones to the right into

Available Zones

to remove from the viewer

Notes:

1. For systems with devices that have controlable volume (such as an AudioTron), select the desired volume (normally 100%).

Add any other RS-232 controlled sources. Refer to the Integration Note for each specific source device.

Add IR devices on the Input/Output tab for other IR controlled sources. Refer to the Configurator Reference Guide .

5 of 5

OMMON

ISTAKES

Altri manuali per CrossPoint 300 Series

Indice

Altri manuali Extron electronics Commutatore a matrice

Extron electronics

Extron electronics MVX 128 VGA A Manuale utente

Extron electronics

Extron electronics TPX 88 Series Manuale utente

Extron electronics

Extron electronics MAV Series Manuale utente

Extron electronics

Extron electronics Matrix 50 Series Manuale utente

Extron electronics

Extron electronics MMX 32 VGA A Manuale utente

Extron electronics

Extron electronics FOX 4G Matrix 14400 Manuale utente

Extron electronics

Extron electronics MAV 44 Series Manuale utente

Extron electronics

Extron electronics MVX VGA A Manuale utente

Extron electronics

Extron electronics ISM 482 Manuale utente

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Manuale utente

Extron electronics

Extron electronics ISM Series Guida rapida

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Manuale utente

Extron electronics

Extron electronics DXP 88 SDI Manuale utente

Extron electronics

Extron electronics MVX Series Manuale utente

Extron electronics

Extron electronics MTPX 1616 Manuale utente

Extron electronics

Extron electronics FOX3 Matrix Series Manuale utente

Extron electronics

Extron electronics DXP 44 4K PLUS Manuale utente

Extron electronics

Extron electronics DMS 1600 Manuale utente

Extron electronics

Extron electronics DTP CrossPoint 108 4K Manuale utente

Extron electronics

Extron electronics TPX 88 Series Manuale utente

Extron electronics

Extron electronics MAV Plus Series Manuale utente

Extron electronics

Extron electronics DTP CrossPoint 108 4K Manuale utente

Extron electronics

Extron electronics DXP DVI Pro Manuale utente

Extron electronics

Extron electronics MSG0804 Manuale utente

Manuali Commutatore a matrice popolari di altre marche

Broadcast Tools

Broadcast Tools SS 8.2 Manuale utente

Altimium

Altimium MATF32 Manuale utente

ALFAtron

ALFAtron ALF-MUK44N Manuale utente

Monoprice

Monoprice Blackbird 15377 Manuale utente

Kramer

Kramer XL 3216VS Manuale utente

PTN

PTN FMX12 Manuale utente

CYP

CYP nT15GX01 Manuale utente

Kramer

Kramer VP-2x2 Manuale utente

Kramer

Kramer Sierra Video 6432V5xl Manuale utente

TESmart

TESmart HMA0402A40 Manuale utente

Octava

Octava HD4XSTPMX Manuale utente

Intelix

Intelix FLX-88 Istruzioni operative

Kramer

Kramer LASSEN XL 3232S Manuale utente

Roland

Roland XS-1HD Manuale utente

Kramer

Kramer VS-66HDCPxl Manuale utente

Atlona

Atlona AT-HDMI-22M Manuale utente

Link

Link HD8X8 Manuale utente

AMX

AMX AVS-OP-2020-117 Istruzioni e ricette