Extron electronics IN1608 xi Series Manuale utente

IMPORTANT:

Go to www.extron.com for the complete

user guide,

installation instructions,

and

specifications bef

ore connecting the

oduct to the po

wer source.

IN1608 xi Series • Setup Guide

The Extron IN1608 xi Scaling Presentation Switcher is an eight input, HDCP-compliant video scaler that accepts a wide

variety of audio and video formats and provides HDMI and DTP/HDBaseT video outputs. This guide provides instructions

for an experienced user to set up and congure IN1608 xi, IN1608 xi SA, IN1608 xi MA 70, IN1608 xi IPCP SA, and

IN1608 xi IPCP MA 70 scalers. It covers how to perform basic operations using the front panel controls and selected Simple

Instruction Set (SIS™) commands.

NOTES:

• For full installation, conguration, menus, connector wiring, and operation details, see the IN1608 xi Series User Guide

at www.extron.com. For installation, conguration, and operation details of the IPCP Pro dual-NIC embedded control

processor, see the IPCP Pro Series User Guide.

• The IN1608 xi Series products can also be congured via the Extron Product Conguration Software (PCS), available at

www.extron.com. For information on using PCS, see the IN1608 xi Series Help le

Installation

IN1608 xi Series Rear Panel Connectors

100-240V ~ 1.5 A MAX

CONFIGURABLE

HDMI HDMI

RS-232 IR

Tx Rx Tx RxG

Tx Rx Tx RxG Tx Rx Tx RxG

HDMI

INPUTS OUTPUTS

Tx Rx

RS-232

2x25W(8Ω)/2x50W(4Ω)

RESET

AUDIO INPUTS OUTPUTS REMOTE

LL1RR

L2 R

CLASS 2 WIRING

L4R

L5R

+48V

VARIABLE

IN1608 xi IPCP SA

MIC/LINE

L6R

SIG LINK

DTP IN

SIG LINK

DTP IN

SIG LINK

OUT

50/60 Hz

RS-232 IR

OVER DTP OVER TP

AMPLIFIED OUTPUT

DTP

HDBT

Tx Rx

RTSCTS

Tx Rx GTxRxG

LAN

AV LAN 2AV LAN 3

AV LAN 1

1234G

DIGITAL I/OCOM 3COM 2COM 1

SSGG

2C34C -S G+S+V

PWR OUT = 6W

IR/SERIAL eBUSRELAYS

BCDGHEFJL

Figure 1. Rear Panel Connectors, IN1608 xi IPCP SA

Power and Input Connections Output Connections Control Connections

AAC power connector

BConfigurable analog 15-pin HD (VGA)

connectors (inputs 1 and 2)

CHDMI inputs (inputs 3 through 6)

DDTP inputs and corresponding RS-232/IR Over

DTP connectors (inputs 7 and 8)

EAnalog audio inputs (associated with inputs 1

through 6)

FMic/Line audio inputs and adjacent phantom

power LEDs

GDTP/HDBaseT output connector and

corresponding RS-232/IR Over

TP connector (output 1C)

HDTP/HDBaseT mode selection switch

for twisted pair output

IHDMI outputs (outputs 1A and 1B)

JAnalog audio outputs

KAmplified audio output

(SA and MA models only)

LRemote RS-232 port

MIPCP Pro dual-NIC

embedded control

processor

(IPCP models only)

NLAN connector

(non-IPCP models

only, see the note and

illustration below)

The IN1608 xi IPCP models feature a built-in Extron IPCP Pro dual-NIC control processor for controlling and monitoring a variety

of external devices, such as projectors and lights (see the IPCP Pro Series Setup Guide for more details).

NOTE: The non-IPCP models have a LAN connector next to the Remote RS-232 connector (see Nin

the illustration at right) instead of the IPCP Pro control processor.

Tx Rx

RS-232

LAN

2x25W(8Ω)/2x50W(4Ω)

RESET

OUTPUTS

REMOTE

CLASS 2 WIRING

VARIABLE

AMPLIFIED OUTPUT

IN1608 xi SA

IN1608 xi • Setup Guide (Continued)

Mounting and Cabling

Step 1 —Mount the device

a. Turn off or disconnect all equipment power.

b. Mount IN1608 xi scaler to a rack using the

pre-installed rack ears, or use an optional

mounting kit for under-desk mounting (see the

two images at right).

The IN1608 xi comes in a 1U, full rack width

enclosure (shown in the examples at right). All

other IN1608 xi models come in 2U, full rack

width enclosures.

Step 2 —Connect inputs

a. Connect analog video sources to the VGA connectors (see gure 1, B, on the previous page).

b. Connect digital HDMI or DVI (with an appropriate adapter) sources to the HDMI connectors (C).

c. Connect a DTP transmitter to the DTP input connectors (D). For cable wiring and recommendations, see Twisted Pair

Recommendations for DTP and HDBaseT Communication on the next page.

Signal LED — Lights green when the unit is receiving an active video signal from a DTP transmitter.

Link LED — Lights amber when a valid link is established to a DTP transmitter.

d. To pass serial or infrared data, connect the control device to the RS-232 and IR Over DTP captive screw connectors

(see RS-232 and IR Over TP Wiring on the next page). Alternatively, insert RS-232 communication to a DTP/HDBaseT

endpoint via Ethernet (see the IN1608 xi Series User Guide for more information).

e. Connect analog audio sources to the inputs via the 5-pole captive screw connectors (E). See Audio Wiring on the next

page for more information.)

f. Connect Mic/Line audio sources to the inputs via the 3-pole captive screw connectors (F).

Step 3 —Connect outputs

a. Set the twisted pair switch (H) to one of the following positions:

• HDBT — Set the twisted pair switch to the Up position to set the twisted pair connector for HDBaseT

communication. The switch returns to the middle position after.

• DTP — Set the twisted pair switch to the Down position to set the twisted pair connector for DTP communication.

b. Connect an DTP/HDBaseT-compatible device to the HDBT output connector (G). For cable wiring and

recommendations, see Twisted Pair Recommendations for DTP and HDBaseT Communication.

Signal LED — Lights green when the scaler is outputting active video.

Link LED — Lights amber when a valid link is established between the scaler and the DTP/HDBaseT sink.

c. To pass serial or infrared data, connect a control device to the RS-232 and IR Over DTP captive screw connector (see

RS-232 and IR Over TP Wiring on the next page). Alternatively, insert RS-232 communication to a DTP/HDBaseT

endpoint via Ethernet (see the IN1608 xi Series User Guide for more information).

d. Connect suitable video displays to the HDMI connectors (I).

e. Connect analog audio devices to the outputs via the 3.5 mm, 5-pole captive screw connectors (J). See Audio Wiring

on the next page for more information.

f. For SA and MA models, connect speakers to the Amplied Output via the 5 mm 4-pole or 2-pole captive screw

connector (K).

Step 4 —Connect control devices

a. To control non-IPCP models through Ethernet, connect a LAN or WAN to the LAN connector (see Non page 1). For the

IPCP models, connect a LAN or WAN to any of the LAN connectors on the IPCP Pro control processor (M). The default

IP address of the scaler is 192.168.254.254. The default subnet mask is 255.255.255.0.

b. For serial RS-232 control, connect a host device to the 3-pole captive screw connector (L). The default baud rate is

9600.

c. For control through USB, connect a host device to the front panel USB mini-B port (see gure 2, Aon page 4).

#8 Screw

(4) Places

Each Side MBU 149

Mounting Bracket

Mounting Screws

(2) Places

Each Side

Furniture Mounting

Rack Ears

Rack Mounting

Step 5 —Set up the IPCP Pro 355 control processor (IPCP models only)

See the IPCP Pro Series Setup Guide, available at www.extron.com, for installation details.

Step 6 —Connect power

Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (see

gure 1, A, on page 1).

Twisted Pair Recommendations for DTP and HDBaseT Communication

Extron recommends using the following practices to achieve full transmission distances and

reduce transmission errors:

• Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron

recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth of

400 MHz.

• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown at

right).

• Limit the use of more than two pass-through points, which may include patch points, punch down connectors, couplers, and

power injectors. If these pass-through points are required, use shielded couplers and punch down connectors.

ATTENTION:

• Do not connect these connectors to a computer or telecommunications network.

• Ne connectez pas ces ports à des données informatiques ou à un réseau de télécommunications.

• DTP remote power is intended for indoor use only. No part of the network that uses DTP remote power should be routed

outdoors.

• L’alimentation DTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise

l’alimentation DTP à distance ne peut être routée en extérieur.

NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:

• Do not exceed 40% ll capacity in conduits.

• Do not comb the cable for the rst 20 meters, where cables are straightened, aligned, and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

• Separate twisted pair cables from AC power cables.

RS-232 and IR Over TP Wiring

To pass bidirectional serial command signals between DTP or HDBaseT-compatible devices, connect a control device to the three

leftmost poles (Tx, Rx, and G) of the 5-pole captive screw connector. To transmit and receive IR signals, connect a control device

to the three rightmost poles (G, Tx, and Rx).

NOTE: Alternatively, RS-232 data can be inserted via Ethernet (see the IN1608 xi Series User Guide for details).

Audio Wiring

Wire the audio input and output connectors as shown

at right. Use the supplied tie wrap to strap the audio

cable to the extended tail of the connector. This does not

apply to the amplied audio output connector on the SA

and MA models.

ATTENTION: For unbalanced outputs, do not

connect wires to the “-” poles (see the Extron

Audio Wiring Card).

ATTENTION : Pour les sorties asymétriques, ne

connectez pas de câbles aux pôles «-» (voir le

Audio Wiring Card d’Extron).

NOTE: The length of exposed wires is critical. The ideal length is 3/16 inch (5 mm).

Balanced Audio Output

Tip

Ring

Tip

Ring

Slee

ves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

Unbalanced Audio InputBalanced Audio Input

Tip

Ring

Tip

Ring

Slee

ves

Tip

Sleeve

Tip

Do not tin the wires!

TIA/EIA-T568B

Pin Wire Color

1 White-orange

2 Orange

3 White-green

4 Blue

5 White-blue

6 Green

7 White-brown

8 Brown

12345678

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

Wire color

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

Wire color

T568A T568B

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

Front Panel Overview

VOLUME

SCALING PRESENTATION SWITCHER

IN1608 xi

INPUTS

HDCP

SIGNAL

OUTPUTS

ENTER

2 3 4 5 6 7 8 1A 1B 1C

CONFIG

1 2 3 4 5 6 7 8

INPUTS

eBUS

OVER

LIMIT

RTS

CTS

COM

IR/S

I/O RELAYS

ABCDE F

Figure 2. Front Panel Features, IN1608 xi IPCP SA

AFront panel configuration port — Connect a host device to the USB mini-B port for device conguration, control, and

rmware upgrades.

BInput selection buttons (1-8) — Press one of these buttons to select an input. The buttons light amber for audio and video,

green for video only, or red for audio only.

CStatus LED indicators

• Input signal LEDs — Light green for each input when active video content is detected.

• Output signal LEDs — Remain lit green when active video is being output or blink amber when output video and sync

are disabled.

• Input HDCP LEDs — Light green for each input signal that is HDCP-encrypted. Analog inputs 1 and 2 cannot be HDCP-

encrypted.

• Output HDCP LEDs — Light green for an output when it is currently HDCP-encrypted.

DMenu and Enter buttons — Press these buttons to access and navigate the on-screen display menu system.

ENavigation buttons — Press these buttons to navigate through the on-screen

display menu system or change selected settings.

FVolume knob and LED indicators — Rotate the Volume knob to adjust the

program, microphone, or output volume. The eight Volume LED indicators light

according to the volume level. The LEDs light in order from bottom to top to

indicate steps from 1% (-99 dB) to 99% (-1 dB). The bottom LED blinks when the

volume is muted. The top LED blinks when the volume is at 100% (0 dB).

GIPCP Pro LED indicators — IPCP Pro models only (see the IPCP Pro Series

Setup Guide for details).

IN1608 xi Series Conﬁguration

To congure IN1608 xi scalers, use the front panel controls and the on-screen display

(OSD) menu, the internal web pages, PCS, or SIS commands.

On-screen Display (OSD) Menu System

To congure IN1608 xi scalers using the OSD menu, connect a display

to either HDMI output or to a DTP/HDBaseT device. The OSD menu

consists of nine submenus accessed using the front panel Menu or

Enter button (see the example above, right).

NOTE: Press and hold the Enter button for 10 seconds to edit

settings in the Communication submenu.

Internal Web Pages

To congure IN1608 xi scalers using the factory-installed web pages in a

web browser (see the example at right), connect the Ethernet port on the

device to a LAN or WAN. The default IP address is 192.168.254.254.

Extron Product Conﬁguration Software

To congure IN1608 xi scalers using PCS, install the software (available on the Extron website, www.extron.com) to a PC

connected to the scaler via Ethernet or front panel USB Cong port. After the installation, start the program. For full instructions,

press <F1> on the keyboard or click the ?button in the software and select Help File.

Basic SIS Command Table

To congure IN1608 xi scalers with specic SIS commands via an RS-232, USB, or Ethernet connection, use the Extron

DataViewer utility or a control system to send and receive SIS commands. The table below lists a selection of SIS commands. For

a full list of SIS commands and variables, see the IN1608 xi Series User Guide at www.extron.com.

Command ASCII Command Response Additional Description

Select audio and video input X!! InX!•All]Selects audio and video input X!.

Select video input only X!& InX! •RGB]Selects the video only input X!.

Select audio input only X!$ InX! •Aud]Selects the audio only input X!.

Execute Auto-Image™AImg0]Executes an Auto-Image on the current input.

Execute Auto-Image and ll 1*A Img1]Executes an Auto-Image and lls the output.

Execute Auto-Image and follow 2*A Img2]Executes an Auto-Image and maintains the aspect ratio of

the current input.

Mute video to black 1B Vmt1]Mutes the video and displays a black output.

Mute video and sync 2B Vmt2]Mutes the video and sync output.

Unmute video and sync 0B Vmt0]Unmutes the video.

NOTE: By default, setting the audio mute with the following commands affects all outputs (configurable through group masters).

Set master audio mute ED7*X(GRPM}GrpmD07*X(] Enable or disable master audio mute.

View master audio mute status ED7GRPM} X(] View the current master audio mute status.

Enable executive mode 1 1X Exe1]Locks the entire front panel.

Enable executive mode 2 2X Exe2]Locks the front panel except for input selection and

volume control.

Disable executive modes 0X Exe0]Allows all front panel adjustments and selections.

Set scaler IP address EX4) CI}Ipi•X4)] Species a new scaler IP address.

Set scaler DHCP mode EX( DH}IdhX(] Enables or disables DHCP (0= default).

Set subnet mask EX4! CS}Ips•X4!] Species a new subnet mask.

Set gateway IP address EX4@CG}Ipg•X4@] Species a new gateway IP address.

Reboot network E2BOOT}Boot2]Restarts the network connection after IP or DHCP

changes.

NOTE: IP settings do not take effect until the E2BOOT}command is executed.

View DTP vs. HDBT Switch

Position

EO3HDBT} X6&]

HdbtO3*X6&]

View the DTP/HDBT mode switch position X6& on

output 1C (verbose mode 2/3 response).

NOTES:

X! = Input selection (1-8)

X( = Enable or disable: 0= off or disabled, 1= on or enabled)

X4) = IP address (nnn.nnn.nnn.nnn), 192.168.254.254 = default)

X4! = Subnet mask (nnn.nnn.nnn.nnn), 255.255.255.0 = default)

X4@ = Gateway address (nnn.nnn.nnn.nnn), 0.0.0.0 = default)

X6& = TP format: 0= DTP format (default), 1= HDBaseT format

Firmware Updates

Download rmware updates from the Extron website and upload them via the internal web pages, PCS, or the Extron Firmware

Loader program.

68-1916-53 Rev. A

11 17

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks(®), registered service marks(SM), and trademarks(TM) are the property of RGBSystems, Inc. or ExtronElectronics

(see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks (®)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator, GlobalScripter,

GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault,

PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge,

VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTPSystems, and ZipClip

Registered Service Mark(SM) : S3 Service Support Solutions

Trademarks (™)

AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple Suppression), Codec

Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital Sync

Validation Processing), eLink, Entwine, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque, ProDSP,

QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, Show Me, SIS, SimpleInstructionSet, Skew-Free, SpeedNav,

StudioStation, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, and ZipCaddy

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Australia

+61.8.8113.6800

+61.8.8351.2511 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

Indice

Altri manuali Extron electronics Interruttore

Extron electronics

Extron electronics SW USB Pro Series Manuale utente

Extron electronics

Extron electronics VEGA AUDIO SW6 Manuale utente

Extron electronics

Extron electronics Matrix 3200 Series Manuale utente

Extron electronics

Extron electronics MLS 306 Manuale utente

Extron electronics

Extron electronics System 8 Plus Manuale utente

Extron electronics

Extron electronics MPS 601 Manuale utente

Extron electronics

Extron electronics SWP123 Manuale utente

Extron electronics

Extron electronics VSW 2VGA A Manuale utente

Extron electronics

Extron electronics DTP T DSW 4K Series Manuale utente

Extron electronics

Extron electronics System 5 IP Series Manuale utente

Extron electronics

Extron electronics MMX 42 AV RCA Manuale utente

Extron electronics

Extron electronics FOX T USW 203 Manuale utente

Extron electronics

Extron electronics SW2 DP Manuale utente

Extron electronics

Extron electronics SW2 VGA DA2 A Manuale utente

Extron electronics

Extron electronics SW 2/4/6 VGAxi Manuale utente

Extron electronics

Extron electronics SW2 VGA DA2 AF R Manuale utente

Extron electronics

Extron electronics SW MTP T 15HD A Manuale utente

Extron electronics

Extron electronics RGB 580xi CCSI AAP Manuale utente

Extron electronics

Extron electronics USB HUB4 AAP Manuale utente

Extron electronics

Extron electronics Extron MediaLink MLS 304MA Manuale utente

Extron electronics

Extron electronics DTP2 T 203 Manuale utente

Extron electronics

Extron electronics ISS 608 Manuale utente

Extron electronics

Extron electronics USB HUB4 Series Manuale utente

Extron electronics

Extron electronics SW2 USB Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente