EZG HW3000 Manuale utente
EZG HW3000®
Hog Waller
Owner’s Manual
Serial Number __________________
Before using the EZG HW3000
Hog Waller®, study and
understand entire Owner’s
Manual.
EZG Manufacturing
1833 North Riverview Road
Malta, Ohio 43758
(740) 749-3512 or 1-800-417-9272
Fax (740) 962-2037 www.ezgmfg.com
EZG HW3000®
EZG MANUFACTURING
1-800-417-9272
EZG Manufacturing 1-800-417-9272 www.ezgmfg.com
TABLE OF CONTENTS
INTRODUCTION...................................................................................................................................3
ABOUT THIS MANUAL.......................................................................................................................3
GENERAL INFORMATION..................................................................................................................3
SAFETY INFORMATION......................................................................................................................3
SAFETY PRECAUTIONS...................................................................................................................4-5
CALIFORNIA PROPOSITION 65 WARNING......................................................................................6
SETUP & OPERATING INSTRUCTIONS.........................................................................................6-9
DAILY MAINTENANCE INSTRUCTIONS.........................................................................................9
OBTAINING SPARE PARTS................................................................................................................10
SERVICE RECORDS............................................................................................................................12
NOTES...................................................................................................................................................13
WARRANTY..........................................................................................................................................14
WARRANTY REGISTRATION............................................................................................................15
S/NEZG586-663www.ezgmfg.com Rev-004Manufacturing 1-2/18/19800-417-92722
TROUBLE SHOOTING GUIDE...........................................................................................................11
UNIT SPECIFICATIONS......................................................................................................................12
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 2
INTRODUCTION
Congratulations on purchasing one of the finest pieces of masonry equipment on the market today! If this is
your first EZG Manufacturing product, you will not be disappointed. If you have previously owned an EZG
Manufacturing product you will find the same high quality and dependability that you have come to expect
from EZG Manufacturing.
ABOUT THIS MANUAL
The purpose of this manual is to inform the owner/employer/and the operator, how to safely operate this
piece of equipment, and make them aware of any hazards. It also contains important information regarding
assembly, set up, operation, and maintenance. It is the Owner/Employers responsibility to make sure that
anyone who operates this machine understands all safety warnings. If you do not understand any items
in this manual, please contact the dealer where this product was purchased, or the manufacturer at the
number listed throughout this manual. If you have any suggestions about how to make this manual easier
to understand, contact the manufacturer. Keep this manual available for reference wherever this piece of
equipment is being used and make it available to any operators.
GENERAL INFORMATION
Illustrations in this manual may show details or components that may not be the same as your machine.
Con-tinuing improvements to the design of this machine may have caused changes that are not included in the
is manual. The information in this document is subject to change without notice.
SAFETY INFORMATION
The following safety symbols and signal words will be used throughout this manual and on the product, for
your safety and the safety of others, please become familiar with their meaning and heed their warnings.
This symbol, either used alone or with a signal word, is used to call your
attention to instructions involving your safety and/or the safety of others. Failure
to follow these instructions will likely result in personal injury or death.
This symbol, either used alone or with a signal word, is used to call your attention
to instructions involving the presence of electric shocks for your safety and/or the
safety of others. Failure to follow these instructions will likely result in personal
injury or death.
This signal word is used to identify a hazard which, if not avoided, will result in
death or serious injury.
This signal word is used to identify a hazard which, if not avoided, could result in
death or serious injury.
This signal word is used to identify a hazard which, if not avoided, could result
in minor or moderate injury.
This signal word is used to identify a hazard which, if not avoided, could result
in property or equipment damage. It also may be used for special instructions
related to performance, maintenance or general items.
DANGER
WARNING
CAUTION
NOTICE
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 3
EZG Manufacturing 1-800-417-9272 www.ezgmfg.com
SAFETY PRECAUTIONS
WARNING
Failure to obey the following safety instructions could result in DEATH
or SERIOUS INJURY.
Read and understand entire manual before operating the HW3000 Hog Waller®
For your safety and the safety of others, replace any missing or damaged warning decals by contacting
the manufacturer at 1-800-417-9272.
0DNHVXUHDQ\RQHRSHUDWLQJWKHHW3000 Hog WallerLVWKRURXJKO\IDPLOLDUZLWKLWVRSHUDWLRQ
.HHSDOOXQDXWKRUL]HGDQGXQWUDLQHGSHUVRQQHOHVSHFLDOO\FKLOGUHQDZD\IURPHW3000 Hog
Waller®.
1HYHURSHUDWHthe HW3000 Hog Waller® if the power cord, plug or switch is damaged.
Never operate the HW3000 Hog Waller® if smoke or a burnt smell is present
1HYHUSHUIRUPDQ\ZRUNRQWKHHW3000 Hog Waller®ZKLOHLWLVUXQQLQJ%HIRUHZRUNLQJRQRU
cleaning the HW3000 Hog Waller®disconnect the power source
1HYHURSHUDWHWKHHW3000 Hog Waller®XQGHUWKHLQÀXHQFHRIDOFRKROGUXJVRUPHGLFDWLRQV
The HW3000 Hog Waller® has been designed and built for the purpose of scrubbing masonry and
concrete walls and should not be used for anything other than its intended purpose.
Only use the correct power supply voltage shown on the identification plate.
Only use an UL approved extension cord approved for outdoor use.
Never modify the plug or use adapter plugs.
Never operate the HW3000 in rain or wet conditions. If damp conditions exist it is recommended to
use a Ground Fault Indicator (GFI) protected supply.
Never use the power cord to carry, pull, or unplug the HW3000. Keep cord away from heat, oil, sharp
edges and moving parts.
WARNING
The HW3000 Hog Waller®
is not designed for or suitable for
use on objects and or surfaces containing asbestos
.
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 4
SAFETY PRECAUTIONS
WARNINGS continued
2SHUDWHRQO\LQSURSHUO\YHQWHGHQYLURQPHQWV
$YRLGEUHDWKLQJGXVWSURGXFHGZKLOHXVLQJWKHHW3000 Hog Waller
'XVWPD\FRQWDLQFU\VWDOOLQH silica and may cause serious health problems.
Do not operate near combustible materials.
$OZD\VNQRZWKHORFDWLRQRIQHDUHVW¿UHH[WLQJXLVKHUV¿UVWDLGNLWDQGHPHUJHQF\SHUVRQQHO
phone numbers in case of emergency.
CAUTION
Failure to obey the following safety instructions could result in MINOR or
MODERATE INJURY.
,QVSHFWthe power cord, switch,IDVWHQHUVEROWVDQGZHOGVIRUQLFNVFUDFNVFXWV
GDPDJHZHDURUORRVH-ness before each use. Repair as needed.
$OZD\VZHDUDSSURYHG33(LQFOXGLQJJODVVHVKHDULQJSURWHFWLRQKDUGKDWVsafety shoes,
DQGYHQWLODWLRQ PDVNVZKHQRSHUDWLQJDHW3000 Hog Waller®.
To prevent unintentional starting of the HW3000 Hog Waller® always make sure the switch is
in the off position before connecting to a power source.
Disconnect all power sources before making any adjustments or performing maintenance on the
HW3000 Hog Waller®.
Be sure to inspect the HW3000 Hog Waller® for any tools such as wrenches and adjusting keys
after any adjustments or maintenance is performed before connecting to a power source.
Do not put the HW3000 down until it has completely stopped.
NOTICE
8VHRQO\IDFWRU\DXWKRUL]HGSDUWV
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 5
EZG Manufacturing 1-800-417-9272 www.ezgmfg.com
California - Proposition 65 Warning
Engine exhaust and some of its constituents, and some dust created by power sanding,
sawing, grinding, drilling, and other construction activities contains chemicals known to
the State of California to cause cancer, birth defects and other reproductive harm. Some
examples of these chemicals are:
Lead from lead based paints - Crystalline silica from bricks -Cement and other masonry
products -Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: Always work in a well ventilated area, and
work with approved safety equipment, such as dust masks that are specially designed to
filter out microscopic particles.
SETUP & OPERATING INSTRUCTIONS
Warning! This equipment is to be operated by trained and qualified personnel
over the age of 18. Death, electrical shock, or serious injury can result.
1. Ensure that the work area is free and clear of debris and people.
2. Be sure that the power cord is clear of and away from the work area.
3. Keep both hands firmly on the HW3000 Hog Waller® during operation.
4. Always allow for reaction torque .
5. If an extension rod is used loosen the lock spanner (figure 1).
6. Attach the dust hose, dust proof ring, and vacuum bag to the extension rod (figure 2).
fig. 1
fig.2
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 6
7. Lock on power switch (figure 3).
fig. 3
8.Adjustable speed switch (figure 4).
9. Installing or replacing abrasive disc (figure 5).
•Insert hex wrench (size 5) into hexagonal screw bolt on the abrasive disc.
•Hold the abrasive disc firmly while turning wrench.
•Install new abrasive disc and tighten bolt.
fig. 5
fig. 4
Attention: Only install the correct size abrasive disc.
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 7
10.LED light installation (figure 6 & 7).
fig. 6
fig. 7
11.Suction power adjustment (figure 8).
•Clockwise to reduce suction power.
•Counter-clockwise to increase power suction.
fig. 8
12.Grinding adjacent edges (figure 9).
•Remove detachable brush segment.
fig. 9
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 8
Warning! Before performing any described maintenance items, make sure
all power sources have been disconnected. Death, electrical shock or other
serious injury can result.
1. Keep the safety devices, ventilation slots and Motor housing as free of dirt and dust as possible.
Clean the unit by rubbing it with a clean cloth or blow it clean using low-pressure compressed air.
2. We recommend that you always clean the unit immediately after using it.
3. Clean the unit regularly by rubbing it with a damp cloth and a little soft soap. Do not use cleaners
or solvents, use of these products will damage the plastic parts in the unit. You must also ensure
that water cannot get into the inside of the unit.
4. Ensure unit is unplugged before removing or inspecting brushes.
5. Removal and replacement of brushes should only be conducted by qualified personnel.
6. Remove and inspect the motor brushes every 40 operating hours.
7. If brushes measure less than 1/4" in length, replace brushes with part #HW-3000-CB.
DAILY MAINTENANCE
13.Removing or replacing the dust hose (figure 10a - 10b).
•Loosen hose clamp with a screw driver.
•Rotate counter-clockwise.
fig. 10a fig. 10b
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 9
EZG Manufacturing 1-800-417-9272 www.ezgmfg.com
OBTAINING SPARE PARTS
Spare parts for your HW3000 Hog Waller® may be obtained by the following procedure:
1. Record the information from the serial number tag.
2. Using the parts reference table in this manual, record the part number or component.
3. Contact your local HW3000 Hog Waller® dealer or EZG Manufacturing at 1-800-417-9272 with
the information recorded.
Part #HW-3000-DSB
Double Strap
Vacuum Bag
Part #HW-3000-GA
Guard Assembly
w/ Bolts
Part
#HW-3000-VH
Vacuum Assembly
Part #HW-30000-EH
Extended Handle
Part #HW-3000-VH-A
Vacuum Hose Assembly
Part #11-162
Abrasive Grinding
Disc
Part #HW-3000-VH-B
Vacuum Hose
Assembly B
Part #HW-3000-CB
Motor Brushes
(2 per set)
Part #11-165
Hex L-Key
5mm x 5"
Part #09-3200
M6 x 1mm x 20mm
Socket Head Screw
Part #HW-501
Arbor
Part #HW-A-1 Arbor Adapter Kit-Cup Disc-Threaded Disc
*Includes the following or items can be purchased individually.
(Serial # HW180648 to present)
(Serial # HW180648 to present) (Serial # HW180648 to present) (Serial # HW180648 to present)
EZG Manufacturing 1-800-417-9272
www.ezgmfg.com
Rev-001 06/14/22 10
Part #HW-3000-BC
Brush Caps
(2 per set)
Altri manuali per HW3000
1
Indice
