Faber FRIGOR 719 Manuale utente
设计
DESIGN
宗培
2017.4.24 图纸名称 PART NAME 图号/物料编码 PART NO.
校对
CO.BY ***
标准化
STANDARD
材料 MATERIAL
80g 双胶纸
业务
seller 郭露
图样标
记
REL
版本号
REV.NO.
重量(g)
WEIGHT
比例
scale
批准
AUTHORIZE
0 美的冰箱事业部
MIDEA REFRIGERATION DIVISION
共页
TOTAL
SHEETS
第页
NO. OF SHEETS
技术要求
标记
MARKER 变更内容 修改日期 签名
①
②
1、 尺寸：32K
2、 印刷颜色：最后一页为彩色，其他为黑色印刷
3、制件必须满足QMB-J53.005 产品说明书及其它类似印刷件技术规范。
4、需要符合美的冰箱事业的最新版《QMB-GC08.007 有害物质管理规定》的限值要求。
5、产品需经过封样合格后方可进行批量生产。
图纸为客户及业务确认使用，厂家需确保二维码可扫且正确
FABER 马来西亚 FRIGOR 719 (FD) LCD
(CB-BCD540WE-ST)说明书
16131000A23482
Instruction Manual
REFRIGERATOR
MODEL: FRIGOR 719
(FD) LCD
FABER
FABER
Please keep children from entering or climbing the refrigerator to avoid locking the
children inside the refrigerator and hurting them when the refrigerator falls.
Do not let the children near the refrigerator when open and close the doors.
Children should be supervised to ensure that they do not play with the appliance.
Never pull out the plug by pulling the power cable. Always hold the plug and pull it
out from the socket. Don't have the power cable pressed under the refrigerator or
feet. When the refrigerator is moved away from the wall, never press or damage
the power cable. When the power cable is damaged or the plug is worn, don't use
it anymore. When the power cable is worn or damaged, you must change it at the
repair station designated by the manufacturer.
When coal gas or other inflammable gases are leaked, close the valve for leaking
gases. Open the door and windows. Don't pull out or insert the plug of refrigerator
or other electric appliances.
Don't put inflammable, explosive, volatile or strongly corrosive substances into
the refrigerator to avoid damaging the refrigerator or starting fire or other
Don't use inflammable solvent near the refrigerator to avoid fire.
It is advisable that you don't put the power socket, voltage stabilizer, microwave
oven and other electric appliances on top of refrigerator to ensure safety. Don't
appliances inside the refrigerator (except for the model
recommended) to avoid electromagnetic interference or other accidents.
When the refrigerator starts to work, don't touch the cold surface of the freezer
compartment, especially with wet hands, to avoid hurting.
The gap between doors and between the door and refrigerator body is small.
Don't put your hands into these areas to avoid finger squeeze. When you open the
refrigerator's door, don't let children approach.
sprinkle water onto rinse the refrigerator with water. Don't put the
refrigerator in wet or easy-to-sprinkle places so as not to influence the electric
insulation property of the refrigerator.
Don't disassemble or reform the refrigerator by yourself. Never damage the
refrigeration pipeline. Please get the refrigerator repaired by professionals.
Don't put fluid substances in bottles or sealed containers into the freezer, like
bottled beer or drinks to avoid that the explosive cracking during freezing causes
other losses.
When power outage or cleaning, pull out the plug. Turn on the power supply after
at least five minutes to avoid that repeated startup might damage the compressor.
When the refrigerator is out of service, please take down the refrigerator's door,
remove the door seal and shelves and put them at proper places to avoid that
children might play inside and cause accident.
This product is a household refrigerator and is only suitable for storage of food
according to state standards. It can't be used for other purposes, like storage of
blood, drugs, biological products and etc.
Safety
For children
For the user
accidents.
use any electric
Don't
03 04
The refrigerator adopts 220V-240V/50Hz AC power, voltage fluctuations
over the range of 187 ~ 242V will cause malfunction or even damage,
so a 750 W automatic voltage regulator must be installed in concert
with the AC power.
1
Left door for refrigerator compartment
Cantilever rack
Turnover beam
Sliding cantilever rack
Fruit and vegetable drawer
Water tank
Drawe of temperature-adjustable compartment
Automatic ice maker
Drawer handle
Leveling leg
Switch for refrigerator compartment lamp
Top lamp for refrigerator compartment
Right door for refrigerator compartment
Butter box
Air duct cover plate
Folded cantilever rack
Side lamp for refrigerator compartment
Gallon bottle rack
UV+Light-wave fresh-keeping lamp
Special-shaped bottle rack
Top lamp for freezer compartment
Upper door for freezer compartment
Lower door for freezer compartment
Decorative cover for bottom beam
2
3
8
9
10
4
5
6
7
11
12
14
15
16
21
22
23
17
18
19
20
24
25
Product description
Left door for refrigerator compartment
Upper door for freezer compartment
Lower door for freezer compartment
Right door for refrigerator compartment
Ice storage box
Ice scoop
Partition plate for lower freezer drawer
Partition plate for upper freezer drawer
Upper freezer drawer
Lower freezer drawer
8
9
10
11
12
13
6
8
9
10
11
12
13
Refrigerator body
1Display
Door handle
Drawer handle
2
3
4
5
6
7
05
1
2
3
4
5
7
0406
1
2
3
4
6
7
8
9
10
11
12
13
16
18
14
15
17
19
20
21
22
23
24
25
5
Wine rack
13
Remove all packaging material before
using the new refrigerator. This
includes the foam base and all
adhesive tape holding the refrigerator
accessories inside and outside.
Clean both the inside and outside of
the refrigerator with wet cloth (a little
detergent could be added into the
warm water to wash the cloth and
then wipe it again with the clean
water);
Prepare an independent two-pole
socket with grounding contact for the
refrigerator and it shall not share a
multi-purpose socket with other
electrical appliances;
Do connect grounding wire! The
grounding pole of the socket shall be
provided with a reliable grounding
wire.
Open the refrigerator body and take
out the accessory (decorative cover
for bottom beam) and the three
screws from the instruction
packaging bag; then install them into
the bottom beam as shown by the
schematic diagram on the right.
The decorative cover for bottom
beam is used as ornament, so you
can choose not to install it. It won't
affect the refrigerator's performance
or conditions no matter whether you
install it or not.
Installation
Transport and Placing of Your
Refrigerator
Transport
Keep upright and avoid squeezing or
vibration during transport. Avoid a
slant angle over 45 degree during
handling.
Avoid the door or top cap from being
under excessive stress when moving;
otherwise, it may become deformed.
Placing
Place your refrigerator in a well-
ventilated place and keep it from heat
source and direct sunlight. Don't
place it in any humid or wet place so
as to avoid rust and weakening of
insulation effect.
There shall be a space not less than
30cm from the top of your refrigerator
and not less than 10cm from both
sides or the back of the refrigerator to
the adjacent walls respectively. This
requirement is good for open and
close of the door and also for heat
emission.
The refrigerator shall be placed on a
flat and firm ground (if not flat, you
can use the leveling legs for
adjustment).
Keep Your Refrigerator Standing
Don't connect your refrigerator to the
power supply immediately after it is
placed vertically. You should keep it
standing for at least 6 hours before
switching it on in order to ensure it
running well.
Make sure the power wire is not
pinned by the refrigerator or other
objects so as to avoid accidents
arising from power wire faults. Please
check the voltage scope of your
refrigerator against the actual power
supply before switching it on.
07 08
Attention
The refrigerator must be disconnected
from the source of electrical supply
before attempting the installation of
accessory.
Don't use mechanical equipment or
other methods to accelerate the
defrosting process except the means
recommended by the manufacturer.
Don't use any electrical appliances in
the food storage compartments except
the model recommended by the
manufacture.
The R134a refrigerant and cyclopentane
foaming material used in the refrigerator
are inflammable. All waste and
discarded refrigerators shall be placed
away from naked fire and they are not
allowed to burn.
Screws
Decorative cover for bottom beam
temperature around 2~8℃,it fails to
Freezer compartment
The temperature in the freezer
compartment is very low so it could
preserve the freshness of food for
long. Those that shall be stored for
long could be put in this compartment
but not exceed the storage period
specified on the packaging of each
You can take out the drawers of the
freezer compartment to increase its
capacity and store more food.
Food suggested to store in freezer
1. The upper drawer of the freezer
could be used to store fish, meat,
ice-cream and etc.
Taking-out and installation of the
lower freezer drawer
1. Pull out the lower freezer drawer
first.
2. Take out the two fixed screws from
the partition plate of the lower
freezer drawer with screw driver
and then take off the partition plate.
3. Take off the rear stopper for the
lower drawer as shown by Fig. A.
4. Take out the lower drawer body
with force as directed by the arrows
in Fig. B.
5. The installation of the lower drawer
body is conducted in the reverse
order. You should install the lower
drawer body first and then install
the rear stopper for the lower
drawer as shown in Fig. C. Finally,
both sides of the drawer shall be
connected to the position shown by
the arrows respectively.
6. The partition plate is installed into
the corresponding slots and then is
fixed with screws. The position of
the partition plate for the lower
drawer could be adjusted
according to your preference.
Don't remove the lower freezer drawer
if not necessary.
2. Ice storage box is used to store the
ice.
3. The lower drawer of the freezer is
used to store fish, meat and
packaged poultry meat.
11 1412
kind of food.
compartment
Rear stopper for the lower drawer
Partition plate for the
lower drawer
Insert into
the edge
Align with
the slot
Lower drawer body
Align with the slot
Positioning hole for
the partition plate
Food suggested to store in
refrigerator compartment
1. Cooked wheaten food, cans, milk,
2. Snack food, food subject to
tainting, dairy product
3. Cooked cold meat, sausage
5. Eggs, butter, cheese
7. Drinks, other bottled food
etc.
4. Fruit, vegetables
6. Cans, seasoning
15 16
Take out, clean and install the ice
cube box
lf the ice maker isn't used for a long
period, ice cubes that are just
produced might have unpleasant
smell. You must take out and clean
the ice cube box.
Open the upper drawer in the freezer
compartment, rotate the knob of ice
maker counterclockwise by 90, turn
the handle from the horizontal position
to vertical position to release the lock
(as shown in Fig. 1 of Pg. 14), pull it
out (as shown in Fig. 2 of Pg. 14) and
take out the ice cube box.
Rinse the ice cube box with warm
water (below 60℃) and don't use
detergent.
Dry the ice cube box completely in air
in case that water droplets in the ice
cube box might cause abnormal
functioning of the ice maker.
When the ice maker can't move,
separate the ice maker as shown in
Fig. 1 and Fig.2. Then install after ice
cubes are melted.
Insert the ice cube box onto the rack
according to original sequence and
rotate to the locked position.
Take out and install the ice maker
When the ice maker isn't used, it
could be taken out and the vacated
space could be used as a part of the
freezer compartment.
Push the Ice Maker button on the
control panel at the refrigerator door
and the icemaking sign disappears.
Open the door and take out the
drawer.
Pull the ice-maker out (as shown in
Fig.1), and then downwards, so that
the ice maker is unhooked (as shown
in Fig. 2).
Pull down the ice maker's power plug
so that it is detached from the ice-
maker's power socket (as shown in
Fig. 3)
Install the ice maker into the original
position, push the Ice Maker button,
the ice-making symbol appears.
Close the door after the ice maker is
installed to the proper place,
otherwise, it might damage the ice
maker.
Unlocked status
Fig.3
Fig.3
Locked status
1
2
3
Ice maker's
power socket
Ice maker's
power plug
Ice
maker's
hook
Indice
