Factor Electronics HD100BaseT-In-Wall-Balun Manuale utente
1
www.factorelectronics.com
info@factorelectronics.com
4159 McConnell Drive Burnaby BC Canada V5A-3J7
Tel: 778-800-1918
Mail: info@factorelectronics.com
HD100BaseT-In-Wall-Balun
4K/18Gbps Wall Plate Switcher for HDMI & VGA Inputs
2
www.factorelectronics.com
info@factorelectronics.com
Thank you for purchasing the Factor Electronics HD100BaseT-In-Wall-Balun. For optimum
performance and safety, please read these instructions carefully before connecting, operating
or adjusting this product. Please keep this manual for future reference.
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be damaged by electrical
spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly
recommended in order to protect and extend the life of your equipment.
3
www.factorelectronics.com
info@factorelectronics.com
Table of Contents
Introduction............................................................................................................... 4
Features.................................................................................................................... 4
Panel Descriptions.................................................................................................... 5
Application Diagram.................................................................................................. 8
Specifications............................................................................................................ 8
Package Contents..................................................................................................... 9
Maintenance ........................................................................................................... 10
Warranty Policy....................................................................................................... 10
Limitations of Warranty............................................................................................ 10
Exclusive Remedies................................................................................................ 11
RMA Policy ............................................................................................................. 12
Standard Replacement.................................................................................... 12
Once you have obtained an RMA number....................................................... 13
Please note ..................................................................................................... 13
4
www.factorelectronics.com
info@factorelectronics.com
Introduction
The HD100BASET-IN-WALL-BALUNis an HDMI 2.0 HDBaseT transmitter/receiver Kit
designed as North America two-gang Wall-plate with switchable HDMI and VGA/Audio inputs.
It supports 4K/60Hz with 4:4:4 chroma sampling, as well as HDMI data rates up to 18Gbps. It
can extend HDMI/VGA signals up to 330ft (100m) for 1080p video, and up to 229ft (70m) for
4K HDR over CAT5e/6a/7 cable. The transmitter is remotely powered by the RX Receiver
through Power Over Cable (POC).Only one (included) power supply is necessary
Features
Switching between HDMI and VGA with 3.5mm audio input, HDMI output with L/R Analog
audio and Coax Digital audio outputs
4K@60Hz with 4:4:4chroma sampling, plus HDR and full 3D formats
1080p up to 100m/330ft, 4K up to 70m/295ft.
Bi-directional IR and RS232 control
POC (Power over Cable) supported. Power direction is from RX to TX
HDCP-2.2/HDCP 1.x and DVI compliant
With ESD protection
5
www.factorelectronics.com
info@factorelectronics.com
Panel Descriptions
TX Transmitter Front Panel
1. Active Input LED indicator –Illuminates when an Active HDMI/VGA signal is
connected
2. Link LED indicator –Illuminates when the HDBT Out on the TX unit is properly
connected to the HDBT In on the RX unit.
3. Input selection button –Press to switch between HDMI and VGA inputs
4. IR Out port –3.5mm mono phone-jack, connect to the IR emitter cable
5. IR In port –3.5mm stereo phone-jack, connect to the IR receiver cable
6. VGA Input –Connect a VGA cable from this port to a VGAsource.
6
www.factorelectronics.com
info@factorelectronics.com
7. L/R Input -- 3.5mm stereo phone-jack, NOTE: the analog audio input 3.5 jack is
modulated with the VGA signal. Without a valid VGA connection the 3.5mm jack will
not transmit audio.
8. HDMI Input –Connect an HDMI cable from this port to an HDMI source.
Rear Panel
1. Mode DIP Switch –2 pin (UP-0, DOWN=1)
00: Valens RS232 pass through (Default)
01: Valens firmware upgrade
7
www.factorelectronics.com
info@factorelectronics.com
10: MCU firmware upgrade
2. 11: Valens RS232 pass through & MCU firmware upgrade
3. Micro USB port –Used for firmware upgrade
4. HDBT Output –Connect to HDBT Input on the RX unit.
5. RS232 port -- 3-pin phoenix terminal connector.
6. DC Power port -- 2-pin phoenix terminal connector, connect to 24V/1ADC power supply if
power is not available at the RX end.
RX Receiver
①Coaxial Audio Output -- S/PDIF audio out, connect to an AV Receiver.
②L/R Audio Output -- RCA connector, connect to an AV Receiver
③HDMI signal link indicator -- Lit when an HDMI sink device is connected
④HDMI Output –Connect to an HDMI enabled display TV or projector
⑤IR Rx/Tx -- Connect to IR receiver cable/ IR emitter cable
⑥Mode DIP Switch –To switch RS-232 serial port between pass-through and firmware
8
www.factorelectronics.com
info@factorelectronics.com
upgrade mode. As below:
00: RS232 pass through
01: Valens firmware upgrade
10: MCU firmware upgrade
⑦RS-232 port -- DB9 female connector, connect to a DTE or DCE
⑧HDBT Input -- RJ45 connector, connect to the HDBT Out port of the transmitter via
cat5e/6
⑨HDBT link indicator –Illuminates with a valid connection between the Transmitter and the
Receiver
⑩Power port -- Use the included 12V/2ADC adaptor to power both the TX and RX units.
⑪Power status indicator -- Lit when the power supply is connected
Application Diagram
9
www.factorelectronics.com
info@factorelectronics.com
Specifications
Bandwidth
18Gbps
18Gbps
Video Input Connectors
1x HDMI, Type A, 19 Pin,
female
1x VGA, 15-pin, female
1x HDBaseT RJ45 connector
Audio Input Connectors
1x 3.5mm stereo earphone
jack (L/R)
/
Audio Output Connectors
/
1x 3.5mm L/R analogue audio, 1x
digital coaxial (RCA)
Video Output Connectors
1x HDBaseT RJ45 connector
1x HDMI Type A, female
Dimensions(W x D x H)
83mm x 83mm x 17mm
113mm x 124mm x 22mm
Shipping Weight
0.6KG
0.375KG
Operating Temperature
32°F to 104°F (0°C to 40°C)
32°F to 104°F (0°C to 40°C)
Storage Temperature
-4°F to 140°F(-20°C to 60°C)
-4°F to 140°F(-20°C to 60°C)
Power Supply
Not included in package
12V/2A DC, screw type connector
Package Contents
1) 1x WP-1 Transmitter
2) 1x RX Reciever
3) 1x IR Emitter
4) 1x IR Sensor
5) 1x Manual
10
www.factorelectronics.com
info@factorelectronics.com
Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this
unit.
Warranty Policy
Factor Electronics HDBT products are warranted against defects in material and workmanship
for two years from the date of shipment. During the warranty period, Factor Electronics will, at
its option, repair or replace products that prove to be defective. Repairs are warranted for the
remainder of the original warranty or a 90 day extended warranty, whichever is longer.
For equipment under warranty, the owner is responsible for freight to Factor Electronics and all
related customs, taxes, tariffs, insurance, etc. Factor Electronics is responsible for the freight
charges only for return of the equipment from the factory to the owner.
All equipment returned for warranty repair must have a valid RMA number issued prior to
return and be marked clearly on the return packaging. Factor Electronics strongly
recommends all equipment be returned in its original packaging.
Factor Electronics obligations under this warranty are limited to repair or replacement of failed
parts, and the return shipment to the buyer of the repaired or replaced parts.
Limitations of Warranty
The warranty does not apply to any part of a product that has been installed, altered, repaired,
or misused in any way that, in the opinion of Factor Electronics, would affect the reliability or
Indice
