Fantasea Nano LED Pro Set Manuale utente
1
2
Table of Contents
1. Introduction ........................................................................................................3
2. Installing and Removing Batteries............................................................. 4
3. Turning the Nano LED Pro On/Off.............................................................. 5
4. Assembling the Cone and Multi-Colored Plastic Disks .......................6
5. Using the Nano LED Pro as a Signaling Device..................................... 6
6. Using the Nano LED Pro as a Back-up Light.......................................... 7
7. Specifications...................................................................................................... 8
3
1. Introduction
The Nano LED Pro is a compact and powerful multi-purpose LED
light system. The Nano LED Pro Set was uniquely designed to be
used as a:
•Powerful diving torch
•Focus light for underwater photography
•Signaling light for above and below water, perfect for
diver or vessel identification
This set combines a compact, powerful multi-use diving torch and
focus light with a new application, similar to the old "Chemical Stick
Lights", but re-usable and environmentally friendly.
Included in the kit are the Nano LED Pro light, white plastic cone
with a lanyard, 4 colored disks and a Y-S Mount, which enables easy
attachment to Flex or Ball & Joint arms.
Cone
Color
Disks
Nano LED Pro
Cone
Lan
y
ard
Y-S Mount
4
2. Installing and Removing Batteries
A. Prior to installing batteries, the white cone should be
removed. Simply detach the cone from the flashlight’s
head by gently pulling them away from each other. Make
sure that when separating the cone from the flashlight,
there is no tension exerted on the cone’s lanyard, which is
wrapped around the flashlight.
B. To open the Nano LED Pro, hold the hand grip firmly in one
hand and turn the flashlight head counterclockwise until it
separates. Pull the flashlight head off. Please make sure
that the light is pointed in an upward position so the
contents do not fall out when opened. Take special care
not to stare into the light beam which is very powerful and
could damage your eyes.
C. Gently remove the LED head by pulling it out.
D. Install or remove the 4 AAA Alkaline batteries carefully.
Please note that this light should not be used with
rechargeable batteries. Make sure that you follow the
instructions diagram printed on the inside of the light. Note
that there are two sets of two batteries, each set pointing
in a different direction.
E. Replace the LED head carefully, making sure that the two
protrusions on the inside of the battery compartment
correspond with the two niches on the LED head. This is
the only way it will fit properly.
F. Carefully place the flashlight head over the threads, and
tighten evenly in a clockwise fashion. Do not use force and
do not allow it to screw down unevenly. Take special care
not to stare into the light beam which is very powerful and
could damage your eyes.
5
G. It is recommended to occasionally apply a slight amount of
silicone grease to the black O-ring seal found on the
flashlight after unscrewing the flashlight head
counterclockwise.
H. In order to attach the cone to the flashlight again, simply
cover the flashlight’s head with the open side of the cone,
so it wraps around it. The cone on the flashlight's head is
held in place by friction. There is no need to force the cone
down on the rubber light cover, but it should be attached
firmly to assure that it is watertight and does not allow
water to seep into the cone. The cone is what gives the
necessary buoyancy to the Nano LED Pro.
3. Turning the Nano LED Pro On/Off
A. It is recommended that you detach the cone from the
flashlight’s head prior to turning the Nano LED Pro on/off in
order to prevent tension from being exerted on the cone’s
lanyard.
B. In order to switch the light on, carefully turn the flashlight
head counterclockwise just enough for the light to turn on.
Once the light is turned on, do not keep turning the
flashlight head counterclockwise, or else the
watertight seal of the light will be damaged.
C. In order to switch the light back off, turn the flashlight
head in a clockwise fashion to the end. Please note that
there is never a need to use force when closing or opening
the light or turning it on or off.
D. Please note: If you are turning the flashlight head more
than half a turn and nothing happens, you are probably
turning it the wrong way.
6
4. Assembling the Cone and Multi-Colored Plastic Disks
A. Detach the cone from the flashlight’s head by gently
pulling them away from each other. Make sure that when
separating the cone from the flashlight, there is no tension
exerted on the cone’s lanyard, which is wrapped around
the flashlight.
B. Choose one of the colorful plastic disks included with the
kit.
C. Push the chosen plastic disk into the white plastic cone,
until it is positioned inside the dedicated track. Note that
the shiny side of the disk should be positioned towards the
bottom open part of the cone.
D. Cover the flashlight head with the open side of the cone, so
it wraps around it. The cone on the flashlight's head is held
in place by friction.
E. When turned on, the Nano LED Pro emits a diffused colorful
light.
F. In order to replace the colored plastic, detach the cone
from the flashlight head, and pull the disk out from the
open side of the cone, by gently pulling the string attached
to the disk. Follow steps A-D in order to insert the new
colored disk into the cone.
5. Using the Nano LED Pro as a Signaling Device
A. When turned on, the Nano LED Pro can be used by divers
as a signaling device.
B. Tie the flashlight’s hand lanyard to the diver’s equipment.
The best way to do this is to tie the hand lanyard around
the tank valve, where the regulator’s first stage is
connected to the tank.
7
C. Leave as little slack as possible to the hand lanyard, so the
light is tied to the tank valve as closely as possible.
D. Since the cone consists of positive buoyancy, the Nano LED
Pro will be pointing up during the dive.
E. After the dive, detach the Nano LED Pro from the tank
valve and soak and rinse exterior components in fresh
water.
6. Using the Nano LED Pro as a Night Dive Light
A. The Nano LED Pro can also be used as a night dive light.
Its compact size means that it can easily be stored inside a
BCD’s pocket and pulled out when necessary.
B. Prior to the dive detach the cone from the flashlight’s head
by gently pulling them away from each other. Make sure
that when separating the cone from the flashlight, there is
no tension exerted on the cone’s lanyard.
C. To get maximum light you should pull the cone off from
the end of the rubber LED cover, leaving it free and only
attached to the light by the lanyard. Or you can detach the
cone’s lanyard from the flashlight by gently pulling the
flashlight out of the plastic lanyard’s ring.
D. Make sure batteries are properly installed (see section 1:
Installing and Removing Batteries).
E. After the dive, carefully soak and rinse exterior
components in fresh water.
8
7. Specifications
•Batteries: 4 x AAA batteries
•Burn time: Up to 2 hours per set of batteries
•LED life time: Over 10,000 hours
•Luminous intensity: Over 50 lumen
•LED type: 3W High-power LED
•Color temperature: 5,000-10,000K
•Color of torch: Metallic coated finish
•Color of light: Clear, yellow, green, blue and red
•Size (mm): 36(W) x 36(D) x 132.5(H)
•Weight: 83 grams (not including batteries)
•Depth ratio: 100 meters/330 feet
visit our website at www.fantasea.com
•You must carefully soak and rinse exterior components in fresh
water after each use.
•Store in a protected, dry and shaded area.
•Remove batteries when storing for an extended period of time.
Indice
Altri manuali Fantasea Accessori per fotocamere
Fantasea
Fantasea Remora Flash Manuale utente
Fantasea
Fantasea BlueRay Illuma Manuale utente
Fantasea
Fantasea FL-15 Manuale utente
Fantasea
Fantasea FP-4 Manuale utente
Fantasea
Fantasea LED 360 Light Manuale utente
Fantasea
Fantasea FS-600 Manuale utente
Fantasea
Fantasea CP-7 Manuale utente
Fantasea
Fantasea FL-10 Manuale utente
Fantasea
Fantasea FSD-1100 Manuale utente
Fantasea
Fantasea BigEye Manuale utente
Fantasea
Fantasea CP 8 Manuale utente
Fantasea
Fantasea Nano Spotter Manuale utente
Fantasea
Fantasea F350D Manuale utente
Fantasea
Fantasea EyeGrabber F Series Manuale utente
Fantasea
Fantasea Fiber Optic Cable Guida
Fantasea
Fantasea CP-4 Pro Guida
Fantasea
Fantasea Nano Fiber Manuale utente
Fantasea
Fantasea FP7100 Manuale utente
Fantasea
Fantasea FL-14 Manuale utente
Fantasea
Fantasea Nano Focus Light Manuale utente
