Fanvil I10 Manuale utente

www.fanvil.com

JJ7J%

.JOJ4*1*OUFSDPN

2VJDL*OTUBMMBUJPO(VJEF

Package Contents



Mini Intercom

Quick Installation

Guide

Screw and tool

www.fanvil.com

JJ7J%

.JOJ4*1*OUFSDPN

2VJDL*OTUBMMBUJPO(VJEF

Connector

Mounting

Template

Physical specification



Device size 88 x 88 x 31 (mm)

i10 No camera, 1 button

With camera, 1 button

No camera, 2 button

i10V

i10D

1) Panel

Camera

Speaker

DSS key Call/Answer Unlock

Mountingdimensions Unit:MM

2) Interface description

Open the rear case of the device, there is a row of terminal blocks for connecting

the power supply, indoor switch. The connection is as follows：

ʒ

ʓʕʔ

Serial

number Description

Ethernet interface: standard

RJ45 interface, 10/100M

adaptive, it is recommended

to use five or five types of

network cable

Power interface: 12V/1A input

A set of short-circuit output

interfaces

A set of short-circuit input

interfaces

1

2

3

4

3) Installation Diagram

Cover Main body Back Shell Cover Main body Back Shell

1) Wall Mount: Attach the installation dimension drawing to the position to be installed,

use the electric drill to punch the hole in the 2 screw holes marked, and use the

hammer to drive the screw into the drilled hole.

Figure 3-1 Three Major Parts of i10&i10V Figure 3-2 Three Major Parts of i10D

Built-in: Attach the installation dimension drawing to the position to be installed, open a

groove of the same size according to the size, use the electric drill to punch the hole in

the 2 screw holes marked, and use the hammer to drive the screw into the drilled hole.

Fanvil Technology Co., Ltd

Email:[email protected]Tel:0755-2640-2199

Add: 4F, Block A, Building 1#, GaoXinQi Hi-Tech Park (Phase-II),

67th District, Bao'An, Shenzhen, China

Fax:0755-2640-2618

2) Remove the cover;

3) Use a screwdriver to remove the 4 screws on the main body to separate the main

body from the rear case;

4) Pass all the wires through the hole in the lower right corner of the bottom case. All

lines must be reserved for a length of 15~20CM;

5) Wall Mount: Align the bottom case with the position of the screw hole that was

previously punched on the wall, and screw in the two screws with a screwdriver to fix

the bottom case to the wall;

Built-in: Place the bottom case into the previously opened groove and screw in the two

screws with a screwdriver to secure the bottom case to the wall;

6) Test whether there is electricity by doing the following:

Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the

speaker beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will

report the IP address by itself. If the work is normal, continue with the next steps.

7) Lock the 4 screws removed in step 3;

8) Cover the cover removed in step 2;

4) Searching Mini Intercom

There are two methods as shown below to search the device.

Methods 1:

Open the iDoorPhone Network Scanner, click the Refresh button to search the device

and find the IP address.

（Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe )

Method 2:

Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the

speaker beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will

report the IP address by itself.

172.18.70.55

In addition, device provides the device surface DSS key operation to switch IP

address acquisition mode:

In the standby mode, long-press the speed dial button for 3 seconds and the beep

will last for 5 seconds. Within 5 seconds, press the speed dial button three times

quickly to switch to the network mode.

If it is in the mode of DHCP and doesn't receive the IP address, switch it to the mode of

static IP (192.168.1.128), broadcast the IP address after the successful switch.

If it is in the mode of static IP address (192.168.1.128), switch it to the DHCP mode,

broadcast the IP address after the successful switch.

If it is in the mode of DHCP and obtain the IP address, the mode will not be switched

and directly broadcast the IP.

5) Mini Intercom Configuration

Step 1: Log in the WEB admin interface of the device

Input IP address (e.g.http://172.18.70.55) into address bar of PC’s web browser.

The default user name and password are both admin

Step 2: Add SIP account

Set SIP server address, port, user name, password and SIP user with assigned SIP

account parameters. Select <enable registration>, click <Apply> to take effect.

Step 3: Set DSS key

Set DSS key speed dial parameters, as shown below, click “Apply”to save this setting.

Type: Hot key.

Number 1: The DSS Key will dial to this Number 1.

Number 2: If number 1 is unavailable, it will be transferred to number 2.

Line: Working line.

Subtype: Speed Dial.

Step 4: Set the Intercom parameters

Step 5: Set the security function

1 set of short-circuit input and output settings, tamper alarm server settings.

Altri manuali per i10

3

Questo manuale è adatto per i seguenti modelli

4

Indice

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente