Fastcabling PoE Powered Switch Manuale utente
PoE Powered Switch Guide EN
Thank you for picking us over the competition. For years we have been a leading provider of PoE over cat5
and Power Fiber System. Please take a few minutes to read through this guide before you get start. Not
only there are some helpful tips, but also we have some guides to help you plan and install your switch.
Installation Requirements
This product is designed for indoor application, pick the cat5e (or higher category) UTP cable. We recommend you to
choose pure copper UTP cable. Pure copper not only can guarantee a maximum of transmission distance, but also
the bandwidth.
NOTE: Do not expose this switch to rain or moisture environment which may cause electric shock or fire.
Hardware Overview
Front Panel
Port
Description
1S-4S
RJ45 port –10/100/1000 Ethernet with PoE, support IEEE802.3af/at.
5S
RJ45 port –Powered by IEEE802.3af/at/bt PoE &10/100/1000 Ethernet for uplink.
LEDs
Status
Power
OFF –power off
Yellow- Power ON
1-5
(Link/ACT)
OFF-No Link
Red-10/100/1000mbps link flashing indicates data exchanging.
1-4
PoE
OFF-No POE
Yellow - 48V standard PoE.
Back Panel
Detail
Description
Ground
ESD grounding for ESD protection. The screws and washer are included.
Power Input
(optional)
Connect to external DC power,48V-57V DC. The PoE powered switch can work with
external power supply unit.
Hardware Installation
Place the PoE Powered Switch on the flat, horizontal surface or mount it on the wall. There are two wall-mounted
spots at the bottom of the switch.
Connecting the Switch
The PoE Powered switch accepts PoE power from another PoE switch/injector or external power input (Power
Supply Unit is not included) from DC48V to DC57V. As the conventional PoE switch only can supply IEEE802.3at
(PoE+), the PoE Powered Switch will have 20W power budget if you connect to conventional PoE switch. However,
this PoE Powered Switch also supports the latest IEEE802.3bt standard which employs all 4 pairs Ethernet cable to
transport the power and data, you can use Fastcabling 90W PoE injector to send the power to this switch which will
has 65W available power budget eventually.
NOTE: Be sure you never connect two uplink ports to the same core switch or router which will create ring network
and block all the network accessing.
1. First, connect one end of Ethernet patch cord to port #5 of PoE powered switch.
2. Next, connect the other end to PoE switch or PoE injector
3. Now Plug PoE IP device to one of ports in PoE Powered Switch.
Once the PoE Powered Switch has been connected to the another PoE switch or PoE injector, the power LEDs will be
turned on. In a short while, you can connect your IP device to one of the PoE port, the corresponding LINK/ACT LEDs
will be turned on in Red, then start flashing. All these means your IP device has been powered up and started
exchange data with PoE Powered switch.
If you only see the PoE LED indicators keep being ON and OFF. Usually, this means the PoE switch can’t verify your IP
device, so it will refuse to release the power in order to protect whatever is in the front-end. Either the failed on
your IP device (including the IP device doesn’t comply with IEEE802.3af/at) or the failed on the cable could cause an
unsuccessful verification process.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the
manufacturer’s label. Connection to a different power source than those specified may result in improper operation,
damage to the equipment or pose a fire hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified
service technician.
3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for
connection to a grounded safety outlet.
4. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to
connect to a 2‑wire outlet as this will defeat the continuity of the grounding wire.
5. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse
can trigger a shock hazard that can result in serious injury or death.
6. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to
connecting the equipment.
7. Protective bonding must be installed in accordance with local national wiring rules and regulations.
Need More Help?
If you require more help setting up your PoE Powered Switch, please head to our help site where you will be able to
find the corresponding help guides and video tourist.
Visit our help site
fastcabling.com/support/
Declaration of Conformity
We. Fastcabling LTD., hereby declare that the products:
Fastcabling PoE Powered Switch
is in conformity with all the essential requirements of EMC Directive 2014/30/EU
Assessment of compliance of the product with the requirements relating to the following specifications:
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
EN 55032:2015+AC:2016 Class A
AS/NZS CISPR 32:2015 Class A
EN 61000-3-2:2014 Class A
EN 61000-3-3:2013
EN 55035:2017
Indice
Altri manuali Fastcabling Interruttore
