FBS C01 Manuale utente
Caution:
Wire devices in accordance
with the NEC.
If you are not sure about
existing conductor wires,
color coding, polarity and
circuit feed contact a
licensed electrician.
Warning:
o be installed and/or used
in accordance with appro-
priate electrical codes and
regulations.
Warning:
o avoid fire, electrical
shock and/or electrocution
turn power OFF at the cir-
cuit breaker before wiring.
IMPOR AN : Please read carefully the following instructions before beginning.
1
OLD WORK
Unscrew the four screws at the
bottom of the box to remove
leveling feet.
2 3
Wire devices in accordance with the NEC.
Attach faceplates to mounting panels.
7
C01 - Installation Instructions -
4 5 Once con-
crete has
cured, remove
temporary
cover. Locate
and pull wires.
Pour concrete. Hand toweling near box edges is
suggested once concrete has been poured.
Attach conduits to the selected
knockouts.
Install temporary cover to pre-
vent debris from entering the
box during concrete pour. Duct
tape any cracks or seams
where concrete may enter.
Fix and secure box to the
floor.
If necessary, use concrete
mixture below and around box
to level the box in accordance
to the final floor level desired.
Install the desired floor covering material (ter-
razzo, tile, limestone,carpet, etc) on the floor.
6
Determine box location and
position in accordance to floor
plans.
Adjust the leveling screws until
the desired level is met.
FBS FLOOR BOX SYS EMS
25060 Hancock Ave
S E 103-125
Murrieta, CA 92562
1-800-216-8307
Questions? 1.800.216.8307 www.FloorBox ystems.comQuestions? 1.800.216.8307 www.FloorBox ystems.comQuestions? 1.800.216.8307 www.FloorBox ystems.com
9 10
Installation Complete.
Secure the cover to the box
using the four supplied
screws.
Before installing the cover,
apply a generous amount of
silicone caulk around the
opening of the floor box
(where the flange sits) .
Verify that all the perimeter
has been properly sealed.
8
Leveling the Box
CORRECT
ile or
Carpet
When a floor covering (tile, wood, carpet) thickness is
known in advance, estimating level to obtain a floor cov-
ering flushed with floor box is suggested (as shown on
the figure above) However it is not completely necessary
When concrete is flushed with box, the
cover can be applied.
When concrete is over poured, the cover
can still be applied. Avoid this situation
***INCORRECT***
Concrete
Floor Box
ile
Floor Box Cover
traight edge cover - Flush Installation
C01 - Installation Instructions -
1) Depending on the thickness of
the floor covering material, level the
box (before pouring concrete) as
necessary to obtain a flush finish
between the cover and the final floor
level as shown on the illustration.
2) Before installing the cover, apply
a generous amount of silicone caulk
around the opening of the floor box.
Verify that all the perimeter has been
properly sealed.
3) Secure the cover to the box using
the four supplied screws.
FBS FLOOR BOX SYS EMS
25060 Hancock Ave
S E 103-125
Murrieta, CA 92562
1-800-216-8307
Questions? 1.800.216.8307 www.FloorBox ystems.comQuestions? 1.800.216.8307 www.FloorBox ystems.comQuestions? 1.800.216.8307 www.FloorBox ystems.com
DI CLAIMER -
(Worldwide)
FBS Floor Box Systems
makes no warranties or rep-
resentations, whatsoever,
express or implied, as to the
merchantability, fitness or
suitability of this product.
Buyer / Installer of this
product must verify the
suitability or approval of this
for the specific use with the
local codes and/or authori-
ties having jurisdiction in the
area where the product will
be installed.
Altri manuali FBS Decoder via cavo
Manuali Decoder via cavo popolari di altre marche
Commercial Electric
Commercial Electric 5053-WH Manuale utente
Motorola
Motorola DCT6412 DUAL-TUNER DVR AND HD SET-TOP - MICROSOFT... Istruzioni per il montaggio
Renkforce
Renkforce 1395556 Manuale utente
Huawei
Huawei FAT9102SD-32G Manuale utente
VISSEM Electronics
VISSEM Electronics Opticube VSOF-OTB-E Manuale utente
Beta
Beta 1844 15-H05/SCK Manuale utente
