FeiYu Tech WG2 Guida rapida
Guilin Feiyu Technology Incorporated Company
-1-
WG2 Gimbal Firmware Upgrade Manual
● Please do not operate any other function button except the ones indicated
by the instructions during upgrade.
● The firmware upgrade software is compatible with Windows operation
system provisionally,including Window XP / 7 / 8 / 8.1 / 10.
● If you want to upgrade it in Mac, Please kindly download the upgrade
software and USB driver for Mac from our official website.
● If you want to get the current version of the gimbal, please do the operations
step 1~7.
1. Download the USB driver from FeiyuTech official website
http://www.feyu-tech.com andinstallit.Thendownloadtheupgrade
software and the firmware for WG2.
2. Please refer the following connection diagram, connect the USB cable
with USB port of the computer and the gimbal. please make sure the
gimbal is powered off until step 7.
Attention
Steps
Guilin Feiyu Technology Incorporated Company
-2-
3. Check the port number in device manager .If the port number is more
than COM10 , please modify it to available number which is within
COM10 .
4. Run the software ---“Gimbal-Update-3AXIS” directly if you have a PC
with Windows XP/7/8/8.1 .
If you have a PC with windows10 operation system, please right click the
icon of the software ,choose “Trouble shoot compatibility”---”Try the
recommended settings”---”test program”, Run the upgrade software in
compatibility mode.
5. Software interface is shown in following picture:
Guilin Feiyu Technology Incorporated Company
-3-
6. Choose correct port number and correct baud rate as 115200, then click
on OPEN button to open COM port.(The serial port number should
bethesameasstep3).
7. Long press the function button, The connection between the gimbal and
the computer will be established automatically, The connection status
and the current version show up(For example, “LINK OK! VERSION 1.
52”) , Keep holding the function button for 2~3 seconds after“LINK OK”
showing up.
Release it, the indicator will alternately flashing blue and red，Which
means the power is ready and the connection is done.
(Tips: if you can’t see that the indicator alternately flashing blue and red,
please long press the function button for 2 seconds again.)
Guilin Feiyu Technology Incorporated Company
-4-
8. Click on OPEN FILE button and choose the correct firmware for the
WG2
9. Click on UPDATE button to start upgrading, the process will display
on the software.
10. After all the blocks of the firmware are completely sent , please click on
Confirm button to finish the upgrade. Close the software then unplug
the USB cable. Long press the function button of the gimbal to power off.
All the upgrade is done.
Guilin Feiyu Technology Incorporated Company
-5-
FAQ
NO.1 “Link OK ”didn’t show up when pressing the function button.
A:
①Please check whether tightly plug in USB cable with USB port, and the USB
cable is right cable from our standard accesseries.
② Please check whether keep the gimbal off until step7.
③ Please check whether choose the right USB port and the baudate as 115200.
④ Please check whether press the function button after clicking on “OPEN
COM“ button.
If you did all the things above right, please replace a new USB cable and try
again.
NO.2 When”LINK OK”and the version of current firmware showing up, click on
“UPDATE START”, but no luck, ”SEND FAIL” just show up to remind me the
update don’t work.
A: It happened because you didn’t hold the function button for enough time,
and the power didn ’ t start well. When the power is ready , the indicator
alternately flashes blue and red, if not, please keep holding the function button
for 2 seconds.
NO.3 After clicking on “UPDATE START”, “send block 10...” show up in the
interface , but ”SEND FAIL” happen during the update.
A: If ”SEND FAIL” shows up during the update, there may be something wrong
with the connection between control boards.
Please try to start update again, if the same issue happen, please kindly send
back to us for repair.
Check more details in tutorial video of G5(The same operation except
the battery as G5): https://youtu.be/yDHTLYQtnbc
–––– END ––––
Note: We reserve the right to change this manual at any time! And the newest
edition will be shown on our official website www.feiyu-tech.com.
Altri manuali per WG2
1
Indice
Altri manuali FeiYu Tech Accessori per fotocamere
FeiYu Tech
FeiYu Tech AK2000 Manuale utente
FeiYu Tech
FeiYu Tech FY WG2 Manuale utente
FeiYu Tech
FeiYu Tech a1000 Manuale utente
FeiYu Tech
FeiYu Tech Vimble 2A Manuale utente
FeiYu Tech
FeiYu Tech SCORP 2 Manuale utente
FeiYu Tech
FeiYu Tech A2000 Manuale utente
FeiYu Tech
FeiYu Tech VLOG pocket2 Manuale utente
FeiYu Tech
FeiYu Tech AK2000C Manuale utente
FeiYu Tech
FeiYu Tech AK4000 Manuale utente
FeiYu Tech
FeiYu Tech FY-G4 GS Manuale
FeiYu Tech
FeiYu Tech SPG Manuale utente
FeiYu Tech
FeiYu Tech AK Series Manuale utente
FeiYu Tech
FeiYu Tech QING Manuale utente
FeiYu Tech
FeiYu Tech VIMBLE ONE Manuale utente
FeiYu Tech
FeiYu Tech SCORP-C Manuale utente
FeiYu Tech
FeiYu Tech MINI 3D Pro Manuale utente
FeiYu Tech
FeiYu Tech AKFI Manuale utente
FeiYu Tech
FeiYu Tech SPG Manuale utente
FeiYu Tech
FeiYu Tech G6 Guida all'installazione
FeiYu Tech
FeiYu Tech G3Ultra Manuale
