FELIXprinters FELIX Pro L Manuale utente

Quick Start Guide

FELIX Pro L/XL

www.FELIXprinters.com/support

[email protected]

Zeemanlaan 15

3401MV IJsselstein

The Netherlands

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 1

1Safety

General safety

-Keep children under the age of 14 out of reach of the printer

-FELIXprinters are only suitable for professional use.

Considerations when in operation.

-Don’t leave the printer unattended, before making sure the first layer is

printed properly

-Don’t lean on the printer.

-Be careful with long hair and wide clothes.

-Don’t transport the printer.

-Make sure all moving parts can move without any obstructions.

-Don’t remove any objects from the hot plate while printing.

-Caution with any moving parts that move in the X, Y and Z direction. Moving

parts can have a pinching hazard.

Electronic safety

-Only use the power supplies and cables supplied by FELIXprinters. Always

turn off and unplug the printer before performing maintenance or

modifications.

-The power supply meets all CE mark regulations and is protected against

short-circuit, overload, over voltage and over temperature.

Printer placement

-Place the FELIXprinter on a stable surface.

-Place the printer out of reach of children. Use the FELIXprinter in a dry

environment at room temperature.

Ventilate

-Good ventilation while printing is advised. When printing ABS, small

concentrations of styrene vapor can be released. This can (in some cases)

cause headaches, fatigue, dizziness, confusion, drowsiness, malaise,

difficulty in concentrating, and a feeling of intoxication.

-We recommend using filament types shown on the FELIXprinters

website. Examples PLA, PETG, ABS-X, Glassbend etc. Other types may be

toxic; please follow instructions from the filament supplier.

Caution with heater elements

-There is a potential risk of burn, as the print head can reach

temperatures of up to 275°C and the heated bed of up to 105°C.

-Don’t place objects on the heated bed, not even when the printer is

turned off.

-Always let the printer cool down for at least 5 minutes before doing

maintenance or modifications.

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 2

2Introduction

Thank you for choosing FELIXprinters!

It is highly recommended to at least read this manual. It explains in short how to make your first print and contains important

information to operate the printer properly.

Kind regards,

FELIXprinters

3Contents

1SAFETY ......................................................................................................................1

2INTRODUCTION ........................................................................................................2

3CONTENTS ................................................................................................................2

4PRINTER SPECIFICATIONS ........................................................................................3

5FELIX PRO L/XL TOUCH AT A GLANCE ....................................................................4

6WHAT’S IN THE BOX?................................................................................................5

INSTALLING TEFLON TUBES ....................................................................................... 6

POWER ON ............................................................................................................. 7

7DISPLAY OVERVIEW .................................................................................................8

8PREPARATION FOR PRINTING ..................................................................................9

CALIBRATION.......................................................................................................... 9

LOAD FILAMENT.................................................................................................... 10

CLEAN THE PRINT SURFACE.................................................................................... 11

9PRINT FROM USB STICK .......................................................................................... 12

10 PRINT AND CONTROL PRINTER VIA WIFI OR LAN ........................................... 13

CONNECT VIA WIFI.............................................................................................. 13

WIRED LAN.......................................................................................................... 13

REMOTE CONTROL................................................................................................ 14

PRINT VIA WEB INTERFACE..................................................................................... 15

11 TIPS AND TRICKS .............................................................................................. 17

FLEXIBLE FILAMENTS............................................................................................... 17

12 MAINTENANCE ................................................................................................ 19

HOW TO MAINTAIN/EXCHANGE HOT-ENDS ........................................................... 19

DUST CLEANERS .................................................................................................... 23

MOTION SYSTEM ................................................................................................... 23

13 DISPLAY MESSAGES......................................................................................... 24

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 3

4Printer specifications

System specifications

-Printer dimensions (L, W, H) 600 x 666 x 776 mm (XL)

-Printer dimensions (L, W, H) 906 x 666 x 966 mm (L)

-Weight 65 kg (L), 80 kg (XL)

-Power requirements: 220 V

Capabilities

-Build volume (L, W, H) 300 x 400 x 400 mm (L)

-Build volume (L, W, H) 600 x 400 x 600 mm

-Layer height range 0.05 - 0.25 mm (L) 0.05 –0.35 (XL)

-Bed temperature: max. 110 °C

-Flex plate

-Software bed leveling

-Automatic nozzle calibrations

Extruders

-Diameter nozzle: 0.35 mm (L) 0.5 (XL) (optional 0.5 and 0.7mm)

-Nozzle temperature: max. 275 °C

-Full metal hot-ends

-Filament flow detection

Interface

-Capacitive Touchscreen, Raspberry processor

-Print server (Repetier-Server)

-Webcam

-Print file management

-16GB memory

Print materials

-Open source 1.75 mm filaments

-Tolerance: ± 0.15 mm

-PLA, PET(G), Flex, ABS-X, PVA, Wood, Glass

Connectivity

-USB flash drive

-WIFI

-Wired Ethernet

Software

-Simplify3D

-Open source Repetier-Host for FELIXprinters.

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 4

5FELIX Pro L/XL at a glance

Display unit

Extruder

Heated bed

Filament roll

Power switch

Power plug

Filament

guide

USB port

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 5

6What’s in the box?

1x Tweezers

1x Power cable

1x MicroSD card + USB

reader

2x Teflon tubes

Recommended tools

NB: The box could contain extra materials like filament you have ordered.

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 6

Installing Teflon tubes

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 7

Power on

1. Insert the power cable.

2. Flip the power switch of the printer (the one on the right), the one on the left is for activating the Power saving system turn

that one on as well (batteries will need to be charge before the system is ready, they start to charge when the switch

labeled UPS is turned on.

3. The lights of the print-head should turn on and immediately after turning on the printer a FELIX bootscreen should be

displayed.

4. Bootup time takes about 40 seconds.

Power switch

UPS Switch

(power saving system)

Ethernet port

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 8

7Display Overview

Shutdown button: To properly shutdown the printer. First press the shutdown button before turning the power switch off. This

ensures proper shutting down of the operating system on the Display unit.

Quick Start Guide FELIX Pro L/XL

3 April 2019

Page 9

8Preparation for printing

Calibration.

IMPORTANT: Only PERFORM BED LEVELING after unboxing. The printer is already fully factory calibrated.

Bed leveling: This tilts the bed in the software so the distance between nozzle and bed is the same everywhere. When to do

this?:

1. After unboxing/moving printer.

2. When you see first layer printed lines are deviating from width across the print surface.

XY and Z Nozzle calibration: These calibrations align the printheads with respect to each other to get an optimal dual head print.

When to do this?

1. After exchanging a hot-end

2. When you clearly see that during dual head printing the nozzles are not aligned in x,y or height.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente