Festo CPX-E DO Series Manuale utente
8126685
CPX-E-...DO-...
Digital output module
8126685
2020-01a
[8126687]
Description| Function,
Parameterisation
Translation of the original instructions
2 Festo — CPX-E-...DO-... — 2020-01a
3Festo — CPX-E-...DO-... — 2020-01a
1 About this Document................................................................................................... 4
1.1 Further applicable documents...................................................................................... 4
1.2 Target group................................................................................................................. 4
1.3 Product version............................................................................................................ 4
1.4 Product labelling.......................................................................................................... 5
1.5 Specified standards...................................................................................................... 5
1.6 UL/CSA Certification..................................................................................................... 5
2 Function........................................................................................................................6
2.1 General..........................................................................................................................6
2.1.1 Product design........................................................................................................7
2.1.2 Display components............................................................................................... 7
2.1.3 Connecting components......................................................................................... 7
2.2 Diagnostics................................................................................................................... 8
3 Parameterisation......................................................................................................... 10
3.1 Overview of parameters................................................................................................ 10
3.2 Module parameters...................................................................................................... 10
3.2.1 Diagnostics of short circuit at output...................................................................... 10
3.2.2 Diagnostics of undervoltage in load supply............................................................ 11
3.2.3 Behaviour after SCO............................................................................................... 11
4 Technical Data............................................................................................................. 12
Table of contents
1 About this Document
This document describes the function and parameterisation of the product stated in the title. Safe use
of the product is described in a separate document è 1.1 Further applicable documents.
1.1 Further applicable documents
All available documents for the product èwww.festo.com/pk.
Documentation Contents
Description of the automation system CPX-E
(CPX-E-SYS)
Detailed description of the
automation system CPX-E
Instruction manual for automation system CPX-E
(CPX-E-SYS)
Instruction manual and important information on
assembly, electrical installation and maintenance
tasks for an automation system CPX-E
Instruction manual digital output module
CPX-E-...DO-... (CPX-E-...DO-...)
Instruction manual and important information on
use and safe application
Documentation of the components in an
automation system CPX-E and the connected
peripherals
Information on using the components
Operating conditions| EX Information on the use of the product in poten-
tially explosive gas atmospheres
Documentation for the higher-order controller
and the additional participants in the network
Information on commissioning and parameterisa-
tion of the components
Tab. 1 Further applicable documents
1.2 Target group
This document is intended for qualified personnel. Experience with electrical control systems is
required in order to understand this documentation.
1.3 Product version
This document refers to the following product versions:
Product Version
CPX-E-8DO Digital output module CPX-E-8DO, revision1 or later
CPX-E-8DO-EX1E1) Digital output module CPX-E-8DO-EX1E, revision1 or later
1) Use in an industrial environment and in process automation according to NE21 and in potentially explosive atmospheres
Tab. 2 Product version
The product version can be identified from the product labelling or with the help of appropriate soft-
ware from Festo.
About this Document
Festo — CPX-E-...DO-... — 2020-01a4
Appropriate software for determining the product version can be found in the Festo Support Portal
èwww.festo.com/sp.
Information on using the software can be found in the integrated Help function.
There may be an updated version of this document for these or later product versions
èwww.festo.com/sp.
1.4 Product labelling
The product labelling is located on the left-hand side of the module. Scanning the printed Data Matrix
Code with an appropriate device opens the Festo Support Portal, with the information appropriate for
the product. Alternatively, the Product Key (11-digit alphanumeric code on the product labelling) can
be entered in the search field of the Support Portal èwww.festo.com/sp.
1Designation
2Revision version
3Pin allocation
4Approvals/warning symbols
5Product key
6Data Matrix Code
7Part number/serial number
Fig. 1 Product labelling
1.5 Specified standards
Version status
EN60529:2013-10 IEC60204-1:2014-10
EN61000-6-2:2005-08 IEC61131-2:2015-05
EN61000-6-4:2007-01 NE21:2012-05
Tab. 3 Standards specified in the document
1.6 UL/CSA Certification
In combination with the UL inspection mark on the product, the information in this section must also
be observed in order to comply with the certification conditions of Underwriters Laboratories Inc. (UL)
for USA and Canada.
About this Document
5Festo — CPX-E-...DO-... — 2020-01a
UL certification information
Product category code NRAQ/NRAQ7
File number E239998
Considered standards UL 61010-1, 3rd Edition, May 11, 2012, revised April 29, 2016
CAN/CSA-C22.2 No. 61010-1-12, 3rd Edition, revision dated April
29, 2016
UL 61010-2-201, 1st Edition, revised February 20, 2017
CSA-C22.2 No. 61010-2-201: 14, 1st Edition, issue date January
01, 2014
UL mark
Tab. 4 UL/CSA Certification Information
– Technical data and environmental conditions may be subject to change in order to comply with
Underwriters Laboratories Inc. (UL) certification requirements for the USA and Canada.
Observe deviations èTechnical data.
– The unit shall be supplied by a power source which fulfils the requirements on a limited-energy
circuit in accordance to IEC/EN/UL/CSA 61010-1 or on a Limited Power Source (LPS) in accord-
ance to IEC/EN/UL/CSA 60950-1 or IEC/EN/UL/CSA 62368-1 or a Class 2 circuit in accordance to
NEC or CEC.
2 Function
2.1 General
A digital output module provides digital outputs to connect electrical consumers. Valves, contactors or
display components, for example, can therefore be actuated with a voltage of 24VDC. Status and
error messages can be shown by LED indicators on the module. The module behaviour can be set
using parameters è 3 Parameterisation.
The power supply of the outputs is electronically protected from short circuit or overload. If this fuse is
tripped, the power supply of the output is switched off and the error is shown by an LED on the mod-
ule.
After the elimination of the short circuit or the overload, the power supply is not switched on again
until after the output is reset (default). This behaviour can be adjusted by parameters. The power sup-
ply of this output is then reactivated automatically without requiring reset of the output.
The electronic fuse of the module is slow-blowing. Electrical consumers with a temporarily higher cur-
rent requirement can therefore also be connected.
Function
6 Festo — CPX-E-...DO-... — 2020-01a
2.1.1 Product design
1LED indicators
2Output terminal strips [X0] … [X3]
3Load power supply terminal strip U OUT [XD]
4Terminal strip interlock
5Linking element
Fig. 2 Product design
2.1.2 Display components
1Module error [P] (red)
2Output channel error 0 … 7 (red)
– Output 0 [X0.0]
– Output 1 [X0.1]
– Output 2 [X1.0]
– …
3Status of output 0 … 7 (yellow)
– Output 0 [X0.0]
– Output 1 [X0.1]
– Output 2 [X1.0]
– …
4Load power supply UOUT [PL] (green)
Fig. 3 LED indicators
2.1.3 Connecting components
Connection [X0]…[X3] Signal
0 +24VDC output 0, 2, 4,…
1 +24VDC output 1, 3, 5,…
2 0VDC output 0, 2, 4,…
3 0VDC output 1, 3, 5,…
Tab. 5 Connection [X0] ... [X3]
Function
7Festo — CPX-E-...DO-... — 2020-01a
Port [XD]1) Signal
0
1
+24VDC load voltage supply UOUT
2
3
0VDC load voltage supply UOUT
1) The ports XD.0 and XD.1 and also XD.2 and XD.3, are interconnected in the terminal strip.
Tab. 6 Connection [XD]
2.2 Diagnostics
Various options are available for diagnosing errors:
– Internal system diagnostics
– LED indicators on the product
The internal system diagnostics is described in the “Description of automation system CPX-E”
è 1.1 Further applicable documents.
The LED indicators on the product are described in the following tables.
Module error [P]1)
LED
(red)
Meaning Remedy
Short circuit/overload at the output or mod-
ule defective
Check the connected actuators, eliminate
short circuit/overload.
Reset the “Behaviour after SCO” parameter
and then set it again.
The necessity of performing this step
depends on the configuration of the para-
meter “Behaviour after SCO”
è 3.2.3 Behaviour after SCO
On
Load power supply UOUT not present or
undervoltage
Check load power supplyOUT.
Off
Normal operating status –
1) flashes once briefly during initialisation of the automation system CPX-E.
Tab. 7 Module error
Function
8 Festo — CPX-E-...DO-... — 2020-01a
Output channel error [X0.0], [X0.1], [X1.0],…
LED
(red)
Meaning Remedy
On
Short circuit/overload at output è Module error
Off
No channel error –
Tab. 8 Output channel error [X0.0], [X0.1], [X1.0], ...
Status of output [X0.0], [X0.1], [X1.0],…
LED
(yellow)
Meaning Remedy
On
Output active (logic1)
Output sends 1-signal
–
Off
Output inactive (logic0)
Output sends 0-signal
–
Tab. 9 Status of output [X0.0], [X0.1], [X1.0], ...
Load power supply UOUT [PL]
LED
(green)
Meaning Remedy
Lit
Load power supplyOUT present –
Off
Load voltage supply UOUT not present or
undervoltage
Check load power supplyOUT.
Tab. 10 Load power supply [PL]
Function
9Festo — CPX-E-...DO-... — 2020-01a
3 Parameterisation
3.1 Overview of parameters
Module parameters are available to adapt the module to the operating situation. General settings that
affect the entire module are made using these parameters.
Module parameters Function number 1) Detailed information
Diagnostics of short circuit at output è Tab. 12
Diagnostics of undervoltage in load supply
4828 + 64m + 0
è Tab. 13
Behaviour after SCO 4828 + 64m + 1 è Tab. 14
Reserved 4828 + 64m + 2…7 –
1) Function number (èDescription of automation system CPX-E); m = module number (counted from left to right, starting from 0)
Tab. 11 Overview of module parameters
3.2 Module parameters
3.2.1 Diagnostics of short circuit at output
The "Diagnostics of short circuit at output" parameter defines whether the diagnostics of the outputs
in regard to short circuit or overload should be activated or deactivated.
When the diagnostics are activated, the error will be sent to the bus module and displayed on the
module by the error LED.
Module parameter – Diagnostics of short circuit at output
Selection via parameter
Bit
Setting Selection via software
F no.1)
4828 +
64m 76543210
Deactivate diagnostics No diagnostics + 0 0
Activate diagnostics Diagnostics (default) + 0 1
1) Function number (èDescription of automation system CPX-E); m = module number (counted from left to right, starting from 0)
Tab. 12
Parameterisation
10 Festo — CPX-E-...DO-... — 2020-01a
Indice
Altri manuali Festo Sistema I/O
Festo
Festo CP-E16...M Series Manuale utente
Festo
Festo SPC200-2AI-U Manuale elenco delle parti
Festo
Festo VIGE-03-FB Series Istruzioni per l'uso e l'installazione
Festo
Festo CPX Series Istruzioni per l'uso e l'installazione
Festo
Festo CP-FB13-E Manuale elenco delle parti
Festo
Festo CPX-...DE Series Manuale utente
Festo
Festo CPX-4AE-4AA-H Manuale utente
Festo
Festo CPX-E- DI Series Manuale utente
Festo
Festo CPX-AP-I-4DI-M8-3P Manuale utente
Festo
Festo CPX-E AI-U-I Series Manuale elenco delle parti
Festo
Festo CPX-2ZE2DA Manuale utente
Festo
Festo CPX Series Manuale utente
Festo
Festo CPX-E-4IOL-P Manuale utente
Festo
Festo CP-E08-M12-CL Manuale utente
Festo
Festo 03-FB-8 Series Manuale utente
Festo
Festo CPX-F8DE-P Manuale elenco delle parti
Festo
Festo CPX-AP-I-8DI-M8-3P Manuale utente
Festo
Festo CPX Series Manuale utente
Festo
Festo CP-FB11-E Manuale elenco delle parti
Festo
Festo CPX-E-4IOL Manuale utente
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Measurement Computing
Measurement Computing PCI-DAS64/M1/16 Manuale utente
