FETtec AIO 35A Manuale utente

FETtec AIO 35A

Manual

Page 1

Table of Contents
Introduction.....................................................................................................................................3
Features..........................................................................................................................................3
Safety warning................................................................................................................................5
Recommended steps for installation of the FE tec AIO 35A.........................................................5
Connection Diagram.......................................................................................................................6
Connection Layout top...............................................................................................................6
Connection Layout bottom.........................................................................................................7
Firmware update and settings........................................................................................................8
FC Firmware update...................................................................................................................8
ESC Firmware update................................................................................................................9
OSD Firmware update..............................................................................................................10
OSD Settings................................................................................................................................11
Issues with the OSD.................................................................................................................12
Move elements in the OSD menu............................................................................................12
Dimensions...................................................................................................................................13
Page 2

Introduction

hank you for purchasing the FE tec AIO 35A.

Features

FC:

•Latest S M32G4 Processor

◦170Mhz + Math accelerator

◦MPU6000

•Supply voltage 12-25V (3S-6S Lipo voltage)

•2x dedicated onboard 5V BEC for V X (max. 600mA each)

◦5V BEC for RX

◦5V/16V BEC for V X (switchable and real Pit*)

•1x 8 pin connector for solder free V X, cam connection and OSD or digital systems

◦VCC, GND, Video in, Video out, BEC 5V/16V, VCS/ X3, RX3

•2x 4 pin connector for receiver and V X

◦Signal, telemetry, 5V, gnd

◦Gnd, 5V, X1, RX1

•5 UAR serials

◦UAR 1 free

◦UAR 2 used for Receiver

◦UAR 3 free

◦UAR 4 used for onboard OSD, can be set free

◦UAR 5 used for ESCs / LM / Onewire

•Solder pad for RGB LEDs

•Supported ESC protocols

◦PWM, Oneshot125, Oneshot42, Dshot150/300/600/1200/2400, FE tec Onewire

•KISS FC firmware

*real Pit-Mode: A power supply pin which is remotely switchable

Page 3

ESC:

•Active current limiting @ 35A

•Input voltage: 3s-6s

•High quality 40V MOSFE s

•S M32G071 @ 64MHz

•up to 128 kHz Motor PWM

•Full sine wave control

•Automatic input signal detection

◦PWM, Oneshot125, Oneshot42, Dshot150/300/600/1200/2400, FE tec Onewire

•FE tec ESC firmware

OSD:

•Onboard OSD

◦Graphic OSD (S M32)

◦Full KISS uning

◦Filter (PIDs, Rates, Settings)

◦LED control (RGB LED, Racewire)

◦V X

◦Live data graphs (Voltage, motor rpm, current, motor temp, gyro values, link quality)

◦KISS GPS support + live map

◦Custom graphic pilot logo

◦Stick overlay

◦Custom layout

◦can be deactivated for usage of digital systems

•Maximum outside dimensions: 30 x 37,5mm

◦Mounting hole arrangement: 20 x 20mm with M2 mounting hole (expandable to M3)

•Overall height: 7,9mm

•Weight: 8,9 g

•Connector type: JS -SH-1mm

Page 4

Safety warning

•Remove propeller before flashing and configuration

•always flash latest firmware before operation

Recommended steps for installation of t e FETtec AIO 35A

•Connect to FE tec Configurator and update to the latest firmware (see firmware update

and settings)

•Install the AIO in your copter (see Connection diagrams for correct wiring and installation)

•Make sure everything is connected properly and check without propellers

•Connect to KISS GUI to proceed with final configuration of the FE tec AIO 35A (FC

configuration)

Page 5

Connection Diagram

Connection Layout top

Receiver connector:

•GND

•5V

•LM: elemetry signal to receiver

•SIG.: Receiver signal to FC

Acronym explanation:

•Motor 1 - 4: pads for motor connection

•GND: Reference Signal Ground

•3-6S - / +: Battery input voltage (12V-27V)

•Reset: Reset button to force the FC in bootloader mode, not needed for normal operation

•RGB_LED: pad for LED connection

•5V/GND/RX4/ X4: If onboard OSD is deactivated these pads are the connection for

another free serial (e.g. GPS)

Page 6

Connection Layout bottom

he 8 pin connector combines all necessary connections for analog or digital V X and camera.

It includes:

•VCC (Lipo+)

•GND for cam and V X

•Video in: Analog video signal from cam

•Video out: Analog video to V X

•BEC 5V/16V: power supply for cam and/or V X, switchable voltage, real Pit capable

•VCS/ X3: for smart audio / tramp configuration or X for digital FPV systems

•RX3: for digital FPV systems

4 pin connector:

•GND

•5V

•X1: function configurable in GUI

•RX1: function configurable in GUI

Onboard OSD Jumper: bridge to deactivate onboard OSD and to activate RX4 and X4

Page 7

Firmware update and settings

T e FETtec AIO 35A works wit KISS/FETtec FC firmware version 1.3RC47i or later !

he FC, ESC and OSD of the FE tec AIO 35A Board are flashable over the FE tec

Configurator.

Download the FE tec Configurator here: https://github.com/FE tec/Firmware/releases.

FC Firmware update

choose USB and select the correct COM

Port and press connect.

You should see the FE tec FC G4 as

shown.

Click “Remote Firmware” button and select

the latest available firmware.

Press “Flash selected!”

FC is flashed now!

Settings can be made in the KISS GUI.

Download:

https://github.com/flyduino/kiss-gui/releases

Reconnect USB after t is step!

We recommend to always use the latest available firmware to get the best user experience.

If you like to try new features and firmware developments you can join our Discord channel and

download the latest beta firmware to try on your own risk (https://discord.gg/pfHAbahzRp)

Page 8

ESC Firmware update

Choose KISS FC Passthrough and press

connect.

all devices should show up now.

he Overview page allows to flash

individual ESCs.

he Setting page allows to adjust all

available ESC parameter.

- Reverse rotation direction

- Slow start

- 3D mode

- PWM min & max signal

- ESC Beep enabled

- Current calibration

–Individual ESC ID (for use on onewire

protocol)

Page 9

In the Telemetry page you can spin the

motors, view and debug the motor

telemetry.

OSD Firmware update

o update the OSD connect to FE tec Configurator and flash via FC passthrough latest

firmware.

Page 10

Indice

Altri manuali FETtec Controllori

FETtec

FETtec FC G4-N Manuale utente

FETtec

FETtec 4in1 ESC 35A Manuale utente

FETtec

FETtec 4in1 ESC 45A Manuale utente

FETtec

FETtec FC G4 Manuale utente

FETtec

FETtec KISS FC Manuale utente

FETtec

FETtec ESC 45A Manuale utente

FETtec

FETtec 4in1 ESC 65A Manuale utente

FETtec

FETtec FC G4 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente