Field Controls FIELD DIRECT VENT SYSTEM REDUCING TEE Manuale utente

www.eldcontrols.com

Please retain these instructions after installation.

This device MUST be installed by a qualied agency in accordance with the manufacturer's installation instructions. The denition of

a qualied agency is: any individual, rm, corporation or company which either in person or through a representative is engaged

in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the

precautions required, and has complied with all the requirements of the authority having jurisdiction.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.

Installation Date:

Installed By: Phone:

FIELD DIRECT VENT SYSTEM

REDUCING TEE

Model: FDVS WITH REDUCING TEE

page 2

Figure 1

Figure 2

REDUCING TEE INSTALLATION

1. Apply a bead of sealant to appliance collar

approximately 1" from end of collar.

(See Figure 1)

2. Remove all oil and grease from the inside of the

appliance reducing tee and apply a bead of

sealant to inside of reducing tee 1⁄2" from end.

(See Figure 1)

3. With a twisting motion, assemble the reducing

tee rmly onto the appliance collar.

4. Push the reducing tee onto the appliance collar,

using care to avoid damaging the appliance

collar or the reducing tee. (See Figure 2)

5. Assemble clamp halves using the supplied 5⁄16"

bolts and square nuts, and install the appliance

clamp onto the reducing tee and tighten

securely. (See Figure 1)

6. Install the supplied self-drilling, self-tapping

anchoring screws through the 4 holes in the

appliance clamp into the appliance collar.

(See Figure 2) No pilot hole is required.

7. Apply sealant to the end of the reducing tee

and anchoring screws. (See Figure 2)

8. After testing and burner adjustments have

been made, apply sealant to the supplied 3⁄8"

sampling port plug screw and install the screw

in the sampling port. (See Figure 2)

page 3

JOINT ASSEMBLY: VENT PIPE TO TERMINATION AND

REDUCING TEE

If necessary, the vent pipe may be cut to length with a

hacksaw or cut o saw.

CAUTION: Use safety glasses and other appropriate

safety gear.

1. Pull outer vent pipe back 1-2" from inner vent

pipe end and remove insulation. (See Figure 3)

2. Slide cover sleeve onto end of vent pipe a few

inches back from end of outer vent pipe.

(See Figure 3)

3. Slide cover ring over stop bead on termination

inner pipe. (See Figure 3)

4. Assemble inner pipe clamp halves using the

supplied 1⁄4" bolts and square nuts, and position

inner pipe clamp 1⁄4" from end of inner pipe.

(See Figure 3)

5. Remove all oil and grease from end of termination

inner pipe and apply a bead of sealant between

the stop bead and retainer bead. (See Figure 4)

6. Apply a thick bead of sealant to inside of inner

vent pipe 1⁄2" from the end of pipe, working the

sealant into the corrugations. (See Figure 4)

7. Push the inner vent pipe onto the termination inner

pipe all the way up to the stop bead.

8. Tighten the inner pipe clamp bolts until both

clamp halves are within 1⁄8" of each other at each

end. (See Figure 5)

9. Slide the cover sleeve and cover ring together to

engage the ring in the groove of the sleeve and

tighten the cover sleeve clamp. (See Figure 6)

10. Repeat this procedure to install vent pipe on

reducing tee.

11. To maintain 1" clearance to combustibles, wrap

minimum 11⁄2" thick ceramic insulation (installer-

supplied) around the exposed portion of the

termination inner pipe (See Figure 6), and secure

with foil tape (installer supplied).

Figure 6

Figure 5

Figure 4

Figure 3

Phone: 252.522.3031 • Fax: 252.522.0214

www.fieldcontrols.com

Warranty

For warranty information about this or any Field Controls product, visit:

www.eldcontrols.com/warranty

Indice

Altri manuali Field Controls Fan

Field Controls

Field Controls 1977200 Manuale utente

Field Controls

Field Controls FAPV180-AC Manuale utente

Field Controls

Field Controls Eliminator EL-1 Manuale utente

Field Controls

Field Controls 46456700 Manuale utente

Field Controls

Field Controls VentCool 2.4 Manuale utente

Field Controls

Field Controls 46263300 Manuale utente

Field Controls

Field Controls 46357800 Istruzioni per il montaggio

Field Controls

Field Controls 1536760 Manuale utente

Field Controls

Field Controls 46457000 Manuale utente

Field Controls

Field Controls 1977100 Manuale utente

Field Controls

Field Controls 46311800 Manuale utente

Field Controls

Field Controls 46261700 Guida

Field Controls

Field Controls 46334800 Manuale utente

Field Controls

Field Controls SWG Stainless Series Manuale utente

Field Controls

Field Controls 2702600 Manuale utente

Field Controls

Field Controls VentCool Tahoe Series Manuale utente

Field Controls

Field Controls CK-63 Manuale utente

Field Controls

Field Controls 46477000 Manuale utente

Field Controls

Field Controls 46490500 Manuale utente

Field Controls

Field Controls 46385600 Manuale utente

Field Controls

Field Controls 46068600 Manuale utente

Field Controls

Field Controls 46115300 Guida utente

Field Controls

Field Controls 4592700 Manuale utente

Field Controls

Field Controls 46267300 Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio