Firegear 73230 Manuale utente
KALEA BAY FIREPLACE
SEE-THROUGH CONVERSION KITS
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS
DO NOT ATTEMPT TO INSTALL OR OPERATE THIS PRODUCT
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE
Installation Instructions
Kits: 73230 (36” Fireplace)
74230 (48” Fireplace)
75230 (60” Fireplace)
76230 (72” Fireplace)
Kalea Bay See-Thru Conversion Kit REV. 4-15-19 Page 2
OFP-36LECO-N OFP-48LECO-N OFP-60LECO-N OFP-72LECO-N
Kit Model # 73230 Kit Model # 74230 Kit Model # 75230 Kit Model # 76230
(1) KB-36-73120 Glass (1) KB-48-73120 Glass (1) KB-60-73120 Glass (1) KB-72-73120 Glass
(1) KB-36-73131 Hood (1) KB-48-74131 Hood (1) KB-60-75131 Hood (1) KB-72-76131 Hood
(1) 76119 Glass Holder - Rt (1) 76119 Glass Holder - Rt (1) 76119 Glass Holder - Rt (1) 76119 Glass Holder - Rt
(1) 76124 Glass Holder - Lt (1) 76124 Glass Holder - Lt (1) 76124 Glass Holder - Lt (1) 76124 Glass Holder - Lt
(11) 77129 Pan Screws SS (11) 77129 Pan Screws SS (11) 77129 Pan Screws SS (11) 77129 Pan Screws SS
Left
G
l
a
s
s
W
i
n
d
shi
e
l
d
Right
Hood Screws
The table below list the replace and the conversion kit model for each replace. Carefully open the conversion kit and
ensure all parts are inside as shown in Fig. 1. Note: In some applications not all screws will be used.
Fig. 1 Conversion kit contents.
CAUTION: Before removing the rear back panel be sure to remove any loose materials out of the rebox area. To remove
the rear back panel and convert replace into a see-through, perform the following steps beginning on page 3.
Tools Needed: Phillips screwdriver or power screwdriver (to install glass holders and hood); 1/4” hex head tip or 1/4” nut
driver (to remove rear panel from replace); pair of gloves to protect hands from any sharp metal edges
Kalea Bay See-Thru Conversion Kit REV. 4-15-19 Page 3
Step 1: REMOVING BACK REAR PANEL
Look at the back side of the replace. Around the outer perimeter area of the back wall are several 1/4” hex head screws
that must be removed (See the shaded area in Fig. 2). Only remove the top and bottom screws on the rear panel. The
nailing ange will remain in place. The back wall panel will remain in one piece. CAUTION: Watch for sharp edges.
Note: The numbers of screws to remove will vary with each replace model. The back panel will not be used again.
Discard back panel and replace the screws previously removed.
Fig. 2 Removing back wall to convert to see-through model.
BACK VIEW REAR PANEL INSTALLED
Side View Detail for Removal Rear Panel Screws
Nailing Flange
Bottom Fin
Valve
Box
B
a
c
k
W
a
l
l
Nailing Flange
N
a
i
l
i
n
g
a
n
g
e
d
e
t
a
i
l
Kalea Bay See-Thru Conversion Kit REV. 4-15-19 Page 4
Step 2: INSTALLING HOOD
The replace requires a hood to be installed into each side of the rebox. One hood would have come with the single
sided replace, the other hood is supplied with this kit. All models require ve (5) screws (#77129) to secure the hood
to the replace except the 72-inch model, which uses seven (7) screws to secure the hood. The hood protrudes outward
1-inch from the top opening of the replace. Fig. 3 shows hole location and installation process for hood installation. The
protruding area of the hood is angled downward to deect heat away, see Hood Detail below.
Fig. 3 Installing hood(s) on the replace.
Hood Screw Locations
FRONT VIEW SIDE VIEW
Hood
(Deector Facing Downward)
Hood Detail
End View
Step 3: INSTALLING GLASS HOLDERS
Install the #76124 (glass holder - left) using two pan head
Phillips screws supplied with the kit.
Align and insert the screw through the glass holder as
shown in Fig. 4. Each screw will thread into the rivet-nut in
the inner side panel of the replace.
Install the #76119 (glass holder - right) in the same manner
on the right side.
Note: Glass holders are designed to hide the screw heads
when installed.
Fireplace Inner
Side Panel
These
rivet-nuts
not used.
7”
Fig. 4 Shows installing the left glass holder.
Kalea Bay See-Thru Conversion Kit REV. 4-15-19 Page 5
Step 4: WINDSHIELD INSTALLATION
The glass windshield slides into each glass holder, at the
same time, on each end of the replace and rest in position
as shown in Fig. 5. The glass will rest on the bottom tab of
each windshield glass holder.
Note: There is only one glass windshield provided with this
kit, the other windshield comes with the replace.
CAUTION: THIS IS TEMPERED GLASS. DO NOT CHIP
GLASS. CHIPPED TEMPERED GLASS CAN BREAK
WITHOUT WARNING.
1
2
GLASS WINDSHIELD
GLASS WINDSHIELD
Side View
Installing Glass
Side View of
Installed Glass
Bottom Tab Bottom Tab
Fig. 5 Installing windshield into clips (glass holders).
Firegear Outdoors
9230 Conservation Way
Fort Wayne, IN 46809
(260) 459-1703
Sales Support: (888) 699-6167
WEB SITE: www.regearoutdoors.com
FOR TECHNICAL SERVICE, CALL: (855) 498-8324
Refer to original Kalea Bay manual for any additional questions.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Firegear Accessori per caminetti
Firegear
Firegear FG-FR-6SSK Manuale utente
Firegear
Firegear ESTOP-RM-KIT Manuale utente
Firegear
Firegear LOF-3010PS246MT-N Manuale utente
Firegear
Firegear FPB-19RBS16TPSI-N Manuale utente
Firegear
Firegear ADP10-OUT Manuale utente
Firegear
Firegear LOF-48LHTMSI-N Manuale utente
Firegear
Firegear LOF-3012HTMSI-N Manuale utente
Firegear
Firegear OFP-36COV Manuale utente
Firegear
Firegear FPB-16SBSTMSI-N Manuale utente
Firegear
Firegear FG-H-2110SS Manuale utente
