Floe VSD6500 Istruzioni operative
1
VSD 6500/8
000
BOAT
LIFT
P/N 511-80075-01 LIFT FRAME
WITH PATENTED EASY LEVEL LEG SYSTEM
ASSEMBLY INSTRUCTIONS
©Manufactured by:
Floe International Inc.
48473 State Hwy. 65
McGregor, MN 55362
www.floeintl.com
Instruction P/N 611-80075-01
Is
ssued 3/4/2018
TOOLS REQUIRED
-(2) 9/16” SOCKETS/WRENCHES
- (2) ¾” SOCKETS/ WRENCHES
- (2) 1-1/8” SOCKETS/WRENCHES
- TORQUE WRENCH
- LOCKING PLIERS
- FRAMING SQUARE
- CLAMP (MIN. 8” OPENING)
2
TIPS
WARNINGS
Torque nuts to specification, not bolts.
Place parts and fasteners in designated locations prior to each step.
Before tightening fasteners to specified torque, ensure that the lift is square.
Measure from corner to corner (A to C/B to D) to verify that the lift is square.
Measure distance between corner posts (A to B, B to C, C to D, A to D) above frame beam and at the
top of the corner post to verify that the lift is square.
Ensure that the lift is level and square before proceeding to install the V-Brace or Ball Screw Tube.
Assemble cradle clamps with given bolt and nut before installing onto cradle beam.
Use a marker to denote fasteners which have been tightened to the specified torque.
Read instructions and understand them before attempting assembly.
DO NOT USE IMPACT WRENCH WHEN ADJUSTING THE EASY LEVEL LEGS.
3
Card Contents (001-60008-00)
Step
Part Numbers
QTY Descriptions Torque
001-70223-00
001-76072-00
4
4
HHCS, 1/2-13 x 5” ss 18-8
NUT, NYLOCK 1/2-13 ALUM.
25 ft. lbs.
001-70219-00
001-71022-00
001-76072-00
001-70125-00
001-76071-00
001-70225-00
001-70121-00
8
16
9
5
6
1
1
HHCS, 1/2-13 x 4” ss 18-8
FLAT WASHER, ½” USS ss 18-8
NUT, NYLOCK 1/2-13 ALUM.
HHCS, 3/8-16 x 6” 18-8 ss
NUT, NYLOCK 3/8-16 ALUM.
HHCS, ½-13 x 6” 18-8 ss
HHCS, 3/8-16 x 4 ½” 18-8 ss
80 ft. lbs.
35 ft. lbs.
001-70117-00
001-70118-00
001-76071-00
001-70125-00
2
2
6
2
HHCS, 3/8-16 x 3 1/2” ss 18-8
HHCS, 3/8-16 x 3 3/4” ss 18-8
NUT, NYLOCK 3/8-16 ALUM.
HHCS, 3/8-16 x 6” 18-8 ss
35 ft. lbs.
001-70219-00
001-71022-00
001-76072-00
6
12
6
HHCS, 1/2-13 x 4” ss 18-8
FLAT WASHER, ½” USS ss 18-8
NUT, NYLOCK 1/2-13 ALUM.
80 ft. lbs.
001-70394-00
001-70211-00
001-70107-00
001-76071-00
001-76072-00
007-05068-00
1
8
8
8
8
1
HHCS, ¾-16 x 2” ss
HHCS, ½-13 x 2” 18-8 ss
HHCS, 3/8 x 1 ¼” 18-8 ss
NUT, NYLOCK 3/8-16 ALUM.
NUT, NYLOCK 1/2-13 ALUM.
CLEVIS, LIFTING CABLE PULLEY
35 ft. lbs.
80 ft. lbs.
4
continued
Step
Part Numbers
QTY Descriptions Torque
001-70213-00
001-70223-00
001-76072-00
001-70212-00
001-71022-00
002-04241-00
007-07625-00
2
2
7
3
4
1
1
HHCS, 1/2-13 x 2 1/2” ss 18-8
HHCS, 1/2-13 x 5” ss 18-8
NUT, NYLOCK 1/2-13 ALUM.
HHCS, 1/2-13 x 2 1/4” ss 18-8
FLAT WASHER, ½” USS ss 18-8
HOLDER, CABLE – 4” SHEAVE
SHEAVE, 4” CLAMP
80 ft. lbs.
001-70365-00
001-07626-00
001-70817-00
001-70110-00
001-71017-00
001-76071-00
001-70124-00
001-76071-00
1
1
1
4
8
4
4
4
HHCS, 3/4-10 x 3” ss
SHEAVE, 2” CLEVIS
NUT, ¾ - 10 JAM ss
HHCS, 3/8-16 x 1 3/4” ss 18-8
FLATWASHER, 3/8” SAE ss 18-8
NUT, NYLOCK 3/8-16 ALUM.
HHCS, 3/8-16 x 5 1/2” ss 18-8
NUT, NYLOCK 3/8-16 ALUM.
100 ft. lbs.
5 ft. lbs.
25 ft.lbs.
5
STEP 1
ATTACH SAND PADS TO ALL FOUR CORNER POST
ASSEMBLIES USING CORNER POST ASSEMBLIES
USING (4) ½” x 5” BOLTS AND (4) ½” NYLOCK NUTS.
TORQUE TO 25 FT-LBS (FIGURE 1.1).
ARRANGE CORNER POSTS AS SHOWN IN FIGURE
1.2.
FIGURE 1
.1
FIGURE 1.2
6
STEP 2
INSERT FRAME BEAM SPACERS INTO
ENDS OF 108” FRAME BEAMS AND
ENSURE HOLES IN FRAME BEAM LINE
UP WITH CLAMP (FIGURE 2.1 & 2.2).
ATTACH FRAME BEAMS TO PRE-
ATTACHED LOWER CORNER POST
CLAMPS USING (2) ½ x 4” BOLTS, (4)
½” WASHERS, AND (2) ½” NYLOCK
NUTS (FIGURE 2.3). TORQUE TO 80
FT-LBS (FIGURE 2.4). REPEAT FOR
EACH CORNER.
FIGURE
2.1
FIGURE
2.2
FIGURE
2.3
FIGURE
2.4
7
STEP 2
ATTACH BALL SCREW CLAMP TO CORNER POST USING
(2) 3/8 x 6” BOLTS, AND (2) NYLOCK NUTS (FIGURE 2.5).
TORQUE TO 35 FT-LBS (FIGURE 2.6).
ORIENT BALL SCREW TUBE BETWEEN CORNER POSTS “A”
& “B” WITH GREASE HOLE AND SUPPORT BOLT VISIBLE
ON OUTSIDE OF LIFT (FIGURE 2.7).
PULL CABLE OUT OF BALL SCREW, ALIGN ON PULLEY,
AND ENSURE THAT THERE ARE NO KINKS OR TWISTS.
PLACE BALL SCREW INTO COUPLER. (FIGURE 2.8).
FIGURE
2.5
FIGURE
2.7
FIGURE
2.8
FIGURE
2.6
8
STEP 2
FIGURE
2.10
FIGURE
2.9
IMPORTANT NOTE: HOLES IN BALL SCREW, BALL
SCREW CLAMP, AND BEARING BLOCK MUST BE
ALINGNED BEFORE INSERTING BOLTS.
(FIGURE 2.9)
ATTACH BALL SCREW TO BALL SCREW CLAMP USING (1) 3/8 x 6” BOLT,
(1) ½ x 6” BOLT, (1) 3/8 NYLOCK NUT, AND (1) ½ NYLOCK NUT (FIGURE
2.10).
IMPORTANT NOTE: BOLTS MUST BE INSERTED INTO THE
BALL SCREW AND BEARING BLOCK (FIGURE 2.11).
TORQUE 3/8” NUT TO 35 FT-LBS AND ½” NUT TO 80 FT-LBS (FIGURE
2.12).
FIGURE
2.11
FIGURE
2.12
FIGURE
2.10
9
STEP 2
FIGURE
2.13
FIGURE
2.14
ATTACH CABLE END OF BALL SCREW TUBE TO COUPLER ON
CORNER POST “A” USING (2) 3/8” x 6” BOLTS, (1) 3/8” x 4 ½”
BOLT, AND (3) 3/8” NYLOCK NUTS (FIGURE 2.13).
IMPORTANT: LIFTING CABLE MUST GO OVER UPPER 3/8” x 6”
BOLT AND UNDER 3/8” x 4 ½” BOLT IN BALL SCREW CORNER
POST COUPLER (FIGURE 2.14). TORQUE TO 35 FT-LBS
(FIGURE 2.15).
FIGURE
2.15
10
STEP 3
SLIDE LOWER V-BRACE CLAMPS TOGETHER ON FRAME BEAM
BETWEEN CORNER POSTS “C” & “D” (FIGURE 3.1)
FASTEN CLAMPS TO V-BRACES USING (2) 3/8” x 3 ½” BOLTS AND
(2) 3/8” NYLOCK NUTS (FIGURE 3.2).
TORQUE TO 35 FT-LBS (FIGURE 3.3).
ATTACH UPPER V-BRACE CLAMPS TO CORNER POSTS “C” & “D”
USING (2) 3/8” x 6” BOLTS AND (2) 3/8” NYLOCK NUTS (FIGURE
3.4)
TORQUE TO 35 FT-LBS (FIGURE 3.5).
ATTACH V-BRACES TO UPPER V-BRACE CLAMPS USING (2) 3/8” x 3
3/4” BOLTS AND (2) 3/8” NYLOCK NUTS (FIGURE 3.4).
TORQUE TO 35 FT-LBS (FIGURE 3.6).
FIGURE
3.1
FIGURE
3.2
FIGURE
3.3
INSIDE OF LIFT
OUTSIDE
OF LIFT
Altri manuali per VSD6500
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Floe Sistema di sollevamento
Floe
Floe PWC1300 Manuale utente
Floe
Floe P1200 Manuale utente
Floe
Floe P-1600 Manuale utente
Floe
Floe VSD 5000 Manuale utente
Floe
Floe V2602 LENGTH BUNKS Manuale utente
Floe
Floe V-3600 Manuale utente
Floe
Floe PWC1300 Manuale dell'operatore
Floe
Floe VSD Manuale utente
Floe
Floe 3800 Manuale utente
Floe
Floe VSD 6000 Manuale utente
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
