Fluke 110 PLUS Manuale utente

PN 4750658

December 2015

Specifications are subject to change without notice. All product names are trademarks of their respective companies.

110 PLUS and 115

True-rms Multimeters

Users Manual

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship for three years from the

date of purchase. This warranty does not cover fuses, disposable batteries, or damage from acci-

dent, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling.

Resellers are not authorized to extend any other warranty on Fluke’s behalf. To obtain service

during the warranty period, contact your nearest Fluke authorized service center to obtain return

authorization information, then send the product to that Service Center with a description of the

problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS

FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE

FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES,

ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the

exclusion or limitation of an implied warranty or of incidental or consequential damages, this limi-

tation of liability may not apply to you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99

Table of Contents

Title Page

Introduction.................................................................................................. 3

Contacting Fluke ......................................................................................... 3

Unsafe Voltage............................................................................................ 3

Test Lead Alert............................................................................................ 3

Safety Information ....................................................................................... 4

Display ........................................................................................................ 7

Terminals..................................................................................................... 9

Rotary Switch Positions............................................................................... 10

Battery Saver(Sleep Mode) ..................................................................... 11

MIN MAX AVG Recording Mode ................................................................. 11

Display HOLD.............................................................................................. 11

Backlight...................................................................................................... 11

Manual and Autoranging ............................................................................. 11

Power-Up Options....................................................................................... 12

Making Basic Measurements ...................................................................... 13

Measuring Resistance ............................................................................. 13

Testing for Continuity............................................................................... 14

110 PLUS and 115

Users Manual

Measuring AC and DC Voltage............................................................... 14

Using Auto Volts Selection (110 PLUS only) .......................................... 14

Measuring AC and DC Millivolts.............................................................. 15

Measuring AC or DC Current (115 only)................................................. 15

Measuring Current above 10 Amps ........................................................ 16

Measuring Capacitance (115 only) ......................................................... 17

Measuring Frequency (115 only) ............................................................ 17

Low Impedance Capacitance Measurements (115 only) ....................... 18

Testing Diodes (115 only)........................................................................... 18

Using the Bargraph..................................................................................... 19

Testing the Fuse (115 only)........................................................................ 19

Maintenance............................................................................................... 20

Replacing the Battery and Fuse.............................................................. 20

Cleaning.................................................................................................. 21

General Specifications................................................................................ 22

True-rms Multimeters

Introduction

The Fluke 110 PLUS and 115 are battery-powered, true-

rms multimeters (hereafter "the Meter" or the “Product”) with

a 6000-count display and a bar graph. This manual applies

to all models. All figures show the 115.

Contacting Fluke

To contact Fluke, call:

USA: 1-888-99-FLUKE (1-888-993-5853)

Canada: 1-800-36-FLUKE (1-800-363-5853)

Europe: +31 402-675-200

Japan: +81-3-6714-3144

Singapore +65-6799-5566

Anywhere in the world: +1-425-446-5500

Or, visit Fluke's website at www.fluke.com.

To register your product, visit http://register.fluke.com.

To view, print, or download the latest manual supplement,

visit http://us.fluke.com/usen/support/manuals.

Unsafe Voltage

The hazardous voltage warning ( Y) shows on the display

when the Meter detects a voltage ≥30 V or a voltage

overload (OL) condition. When making frequency

measurements >1 kHz, the Ysymbol is unspecified.

Test Lead Alert

XW Warning

Personal injury or damage to the Meter can

occur if you attempt to make a measurement

with a lead in an incorrect terminal.

To remind you to check that the test leads are in the

correct terminals,  is briefly displayed and an audible

beep sounds when you move the rotary switch to or

from any A(Amps) position.

110 PLUS and 115

Users Manual

Safety Information

A Warning identifies conditions and procedures that are dangerous to the user. A Caution identifies conditions and procedures that can

cause damage to the Product or the equipment under test.

XW Warning

To prevent possible electrical shock, fire, or personal injury:

•Read all safety information before you use the Product.

•Carefully read all instructions.

•Do not use the Product around explosive gas, vapor, or in damp or wet environments.

•Comply with local and national safety codes. Use personal protective equipment (approved rubber gloves,

face protection, and flame-resistant clothes) to prevent shock and arc blast injury where hazardous live

conductors are exposed.

•Examine the case before you use the Product. Look for cracks or missing plastic. Carefully look at the

insulation around the terminals.

•Do not use test leads if they are damaged. Examine the test leads for damaged insulation and measure a

known voltage.

•Limit operation to the specified measurement category, voltage, or amperage ratings.

•Use the correct terminals, function, and range for measurements.

•Do not touch voltages > 30 V ac rms, 42 V ac peak, or 60 V dc.

•Do not exceed the Measurement Category (CAT) rating of the lowest rated individual component of a

Product, probe, or accessory.

•Use Product-approved measurement category (CAT), voltage, and amperage rated accessories (probes,

test leads, and adapters) for all measurements.

True-rms Multimeters

Safety Information

•Do not apply more than the rated voltage, between the terminals or between each terminal and earth

ground.

•Remove all probes, test leads, and accessories that are not necessary for the measurement.

•Do not use in CAT III or CAT IV environments without the protective cap installed on test probe. The

protective cap decreases the exposed probe metal to <4 mm. This decreases the possibility of arc flash

from short circuits.

•Do not work alone.

•Measure a known voltage first to make sure that the Product operates correctly.

•Replace the batteries when the low battery indicator shows to prevent incorrect measurements.

•Remove the batteries if the Product is not used for an extended period of time, or if stored in temperatures

above 50 °C. If the batteries are not removed, battery leakage can damage the Product.

•Remove all probes, test leads, and accessories before the battery door is opened.

•The battery door must be closed and locked before you operate the Product.

•Do not use the Product if it operates incorrectly.

•Disable the Product if it is damaged.

•Use the Product only as specified, or the protection supplied by the Product can be compromised.

WCaution

Do not use the Auto Volts function to measure voltages in circuits that could be damaged by this function’s low

input impedance (≈3 kΩ) (110 PLUS only).

110 PLUS and 115

Users Manual

Symbols

XWARNING. HAZARDOUS VOLTAGE. Risk of

electric shock. WWARNING - RISK OF DANGER. Consult user

documentation.

AC (Alternating Current) Fuse

DC (Direct Current) TDouble Insulated

Battery (Low battery when shown on the display.) Earth

PConforms to European Union directives. Both direct and alternating current

ÃConforms to relevant South Korean EMC Standards.

Measurement Category II is applicable to test and measuring circuits connected directly to utilization points (socket outlets

and similar points) of the low-voltage MAINS installation.

Measurement Category III is applicable to test and measuring circuits connected to the distribution part of the building’s

low-voltage MAINS installation.

Measurement Category IV is applicable to test and measuring circuits connected at the source of the building’s low-voltage

MAINS installation.

~This product complies with the WEEE Directive marking requirements. The affixed label indicates that you must not discard

this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in

the WEEE Directive Annex I, this product is classed as category 9 "Monitoring and Control Instrumentation" product. Do not

dispose of this product as unsorted municipal waste.

True-rms Multimeters

Display

15 16

edy02f.eps

No. Symbol Meaning Model

The Meter function is set to Continuity. 110 PLUS, 115

The Meter function is set to Diode Test 115

Input is a negative value. 110 PLUS, 115

YXHazardous voltage. Measured input voltage ≥30 V, or voltage overload

condition (OL). 110 PLUS, 115

Display hold enabled. Display freezes present reading. 110 PLUS, 115

110 PLUS and 115

Users Manual



 MIN MAX AVG mode enabled.

Maximum, minimum, average or present reading displayed 110 PLUS, 115

LoZ The Meter is measuring voltage or capacitance with a low input impedance. 110 PLUS, 115

nµF mVµA

MkΩkHz Measurement units. 110 PLUS, 115

DC AC Direct current or alternating current 115

Battery low warning. 110 PLUS, 115

610000 mV Indicates the Meter’s range selection. 110 PLUS, 115

(Bar graph) Analog display. 110 PLUS, 115

Auto Volts

Auto

Manual

The Meter is in the Auto Volts function.

Autoranging. The Meter selects the range for best resolution.

Manual ranging. User sets the Meter’s range.

110 PLUS

110 PLUS, 115

Bar graph polarity 110 PLUS, 115

 WThe input is too large for the selected range. 110 PLUS, 115

 WTest lead alert. Briefly displayed whenever the Meter’s function switch is

rotated to or from any A position. 115

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Fluke Multimetro

Fluke

Fluke 8050A Manuale utente

Fluke

Fluke 28 II Ex Manuale per l'uso e la cura

Fluke

Fluke 12E Manuale utente

Fluke

Fluke 113 Manuale utente

Fluke

Fluke 106 Manuale utente

Fluke

Fluke 233 Manuale utente

Fluke

Fluke ProcessMeter 787 Manuale utente

Fluke

Fluke CNX 3000 Manuale utente

Fluke

Fluke 75 Manuale utente

Fluke

Fluke a3000 FC Manuale per l'uso e la cura

Fluke

Fluke 8808A Guida alla configurazione

Fluke

Fluke Ti30 Manuale utente

Fluke

Fluke 112 Manuale utente

Fluke

Fluke 87 TRUE RMS MULTIMETER Manuale utente

Fluke

Fluke 8021B Manuale utente

Fluke

Fluke 28 II Ex Manuale per l'uso e la cura

Fluke

Fluke 8060A Manuale utente

Fluke

Fluke III Series Manuale utente

Fluke

Fluke LinkRunner Duo Manuale utente

Fluke

Fluke 8842A Manuale utente

Fluke

Fluke 8505A Manuale utente

Fluke

Fluke 707 Istruzioni per l'installazione e il funzionamento

Fluke

Fluke 110 Manuale per l'uso e la cura

Fluke

Fluke 8808A Manuale utente

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Mastech

Mastech MY70 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

Mastech

Mastech MS8238C Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente

Morris

Morris 57074 Manuale utente

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Manuale utente