Fluke 2000ACC Manuale utente

2000ACC

Accessory Kit

Instructions

Contact Fluke

Fluke Corporation operates worldwide. For local contact

information, go to our website: www.fluke.com.

To register your product, or to view, print, or download the

latest manual or manual supplement, go to our website:

www.fluke.com/productinfo.

+1-425-446-5500 fluke-info@fluke.com

Safety Information

A Warning identifies hazardous conditions and procedures

that are dangerous to the user. A Caution identifies

conditions and procedures that can cause damage to the

Product or the equipment under test.

 Warning

To prevent possible electrical shock, fire, or

personal injury:

Read all safety information before you use the

Product.

Use the Product only as specified, or the protection

supplied by the Product can be compromised.

Carefully read all instructions.

Fluke Corporation

P.O. Box 9090

Everett WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

PN 5416998 (English)

1/2023

subject to change without notice. All Product names are

trademarks of their respective companies.



Comply with local and national safety codes. Use

personal protective equipment (approved rubber

gloves, face protection, and flame-resistant

clothes) to prevent shock and arc blast injury where

hazardous live conductors are exposed.

Use Product-approved measurement category

(CAT), voltage, and amperage rated accessories

(probes, test leads, and adapters) for all

measurements.

Do not touch voltages >30 V ac rms, 42 V ac peak,

or 60 V dc.

Do not use the Product around explosive gas,

vapor, or in damp or wet environments.

Do not exceed the Measurement Category (CAT)

rating of the lowest rated individual component of a

Product, probe, or accessory.

Do not use test leads if they are damaged. Examine

the test leads for damaged insulation, exposed

metal, or if the wear indicator (if present) shows.

Check test lead continuity.

Keep fingers behind the finger guards on the

probes.

Do not use in CAT III or CAT IV environments

without the protective cap (if included with the

Product) installed on test probe. The protective cap

decreases the exposed probe metal to <4 mm. This

decreases the possibility of arc flash from short

circuits.

Do not use a shrouded banana jack accessory such

as an alligator clip with an unshrouded 4 mm

banana probe tip terminal in a hazardous electrical

installation. Due to the lack of a shroud, the probe

tip connector does not provide suitable insulation

to accessible parts with this type of assembly.

Symbols

The table below lists the symbols that can be used on the

Product or in this document.

Maintenance

Clean with a soft towel moistened with water and mild

detergent. DO NOT IMMERSE in liquid.

Electrical Specifications

Refer to markings on probe assembly and accessories for

voltage and current specifications. If no CAT rating is

marked, by default ratings are 30 V ac rms, 42 V ac peak or

60 V dc, 8 A. Probe tips with >19 mm (0.75 in) exposed metal

arerated30Vac,60Vdc,≤8A.

Environmental Specifications

Symbol Description

Consult user documentation.

WARNING. RISK OF DANGER.

WARNING. HAZARDOUS VOLTAGE. Risk of

electric shock.

Double insulated



Measurement Category II is applicable to test

and measuring circuits connected directly to

utilization points (socket outlets and similar

points) of the low-voltage MAINS installation.



Measurement Category III is applicable to test

and measuring circuits connected to the

distribution part of the building’s low-voltage

MAINS installation.



Measurement Category IV is applicable to test

and measuring circuits connected at the

source of the building’s low-voltage MAINS

installation.

Conforms to European Union directives.

Te m p e ra t u re -20 °C to 50 °C (-4 °F to 122 °F)

Relative humidity 0 % to 95 %, 0 °C to 35 °C

(32 °F to 95 °F)

Altitude 2000 m

Safety IEC 61010-031: Pollution Degree 2

LIMITED WARRANTY

This Fluke product will be free from defects in material and

workmanship for 1 year from the date of purchase. This

warranty does not cover fuses, disposable batteries, or

damage from accident, neglect, misuse, alteration,

contamination, or abnormal conditions of operation or

handling. Resellers are not authorized to extend any other

warranty on Fluke’s behalf. To obtain service during the

warranty period, contact your nearest Fluke authorized

service center to obtain return authorization information,

then send the product to that Service Center with a

description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR

PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM

ANY CAUSE OR THEORY. Since some states or countries do

not allow the exclusion or limitation of an implied warranty or

of incidental or consequential damages, this limitation of

liability may not apply to you.

11/99

Indice

Altri manuali Fluke Apparecchiature di prova

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente