Fluke T5-600 Istruzioni per l'uso e l'installazione

PN 686953

March 1998

T5-600/T5-1000

Electrical Tester

Service Information

Introduction

This service information sheet provides the following information for the T5-600 and T5-1000 Electrical

Testers (hereafter referred to as "the tester").

•Safety information

•Parts and service information

•Specifications

•Cleaning procedure

•Required equipment

•Performance tests

•Parts and accessories list

•Battery replacement procedure

For operating instructions, refer to the T5-600/T5-1000 Electrical Tester Instruction Sheet.

Safety Information

Warning

To avoid possible electric shock or personal injury, follow these guidelines:

•Use caution when working with voltages above 30 V ac rms, 42 V ac peak, or

60 V dc. Such voltages pose a shock hazard.

•Do not use the tester if it or its test leads appear damaged, or if you suspect

that the tester is not operating properly.

•Before each use, verify the tester’s operation by measuring a known

voltage.

•Disconnect the live test lead before disconnecting the common test lead.

•When using the probes, do not touch the metal probe tips.

•Never apply more than the rated voltage, as marked on the tester, between a

terminal and earth ground.

•To avoid false readings, which could lead to possible electric shock or

personal injury, replace the battery immediately after the battery indicator

appears (M).

•Do not use controls, adjustments, or procedures not documented or

approved by Fluke Corporation.

T5-600/T5-1000

Electrical Tester

Parts and Service

The tester is warranted to be free from defects in material and workmanship for two years, while under normal

use. Parts and repairs are warranted for 90 days. For the complete warranty statement, refer to the

T5-600/T5-1000 Electrical Tester Instruction Sheet.

To order parts, or for warranty service, contact Fluke as follows:

USA and Canada: 1-888-993-5853

(1-888-99-FLUKE)

Europe: +31 402-678-200

Japan: +81-3-3434-0181

Singapore: +65-*-276-6196

Anywhere in the world: +1-425-356-5500

Or, visit Fluke’s Web site at www.fluke.com.

Specifications

Accuracy is specified for one year after calibration, at 18 °C to 28 °C (64 °F to 82 °F) with relative humidity

to 90 %. AC conversions are ac-coupled, average responding, and calibrated to the rms value of a sine wave

input. Accuracy specifications are given as follows:

±([ % of reading] + [number of least significant digits])

Temperature coefficient of 0.1 x (specified accuracy)/ °C for <18 °C or >28 °C (<64.4 °F or >82.4 °F)

General Specifications

Calibration One-year calibration cycle.

Maximum Voltage

Between any Terminal

and Earth Ground

T5-600: 600 V rms, Overvoltage Category III

T5-1000: 1000 V rms, Overvoltage Category III

Temperature Operating: -10 °C to +50 °C (14 °F to 122 °F); Storage: -30 °C to +60 °C (-22 °F to +140 °F)

Altitude Operating: 2000 m (6562 ft); Storage: 10,000 m (32808 ft)

Relative Humidity 0 % to 95 %, 5 °C to 30 °C (41 °F to 86°F); 0 % to 75 %, 30 °C to 40 °C (86 °F to 104 °F);

0 % to 45 %, 40 °C to 50 °C (104 °F to 122 °F)

Battery Type and Life AA (2); 400 hours continuous with alkaline; 200 hours continuous with zinc chloride

Shock, Vibration 1 m drop at 15 °C to 35 °C (59 °F to 95 °F) per ANSI/ISA-S82.01-1994 and EN 61010-1 1993.

Sinusoidal vibration per MIL-PRF-28800F for a Class 2 instrument

(5 Hz to 55 Hz, 3 g maximum)

Surge Protection T5-600: 6 kV per IEC 1010-1, 1990-09; T5-1000: 8 kV per IEC 1010-1, 1990-09

Enclosure Rating IP 52 per IEC 529, no vacuum applied

Service Information

Cleaning the Tester

General Specifications (continued)

RF Field Specification 0.5 % full scale + (specified accuracy) at 3 V/m up to 100 MHz

Safety Complies with ANSI/ISA-S82.01-94 for use in overvoltage category III (CAT III) locations,

UL3111, CSA/CAN C22.2 No.1010.1-92, and EN61010-1 1993.

EMC EN 50081-1, EN 50082-1

Certifications

UL, VDE, and CSA certifications pending.

Resolution and Accuracy

Function T5-600 Range T5-1000 Range Resolution Accuracy

K600 V rms 1000 V rms 1 V ±(1.5 % + 2 digits)

L600 V 1000 V 1 V ±(1 % + 1 digit)

?100.0 A 100.0 A 0.1 A ±(3 % + 3 digits)

e1000 Ω1000 Ω1 Ω±(1 % + 2 digits)

Input Characteristics

Input Protection

Function Input Impedance (nominal) T5-600 T5-1000

K1 MΩ, <100 pF ac-coupled 600 V rms 1000 V rms

L1 MΩ, <100 pF 600 V rms 1000 V rms

e>2.6 kΩ600 V rms 1000 V rms

Open Circuit Test Voltage Short Circuit Current

e2.4 V dc (nominal) <600 µA

Cleaning the Tester

WWarning

To avoid electric shock or damage to the tester, never allow water inside the

case. To avoid damaging the tester’s case, never use solvents on the tester.

If the tester requires cleaning, wipe it down with a cloth that is lightly dampened with water or a mild

detergent. Do not use aromatic hydrocarbons, chlorinated solvents, or methanol-based fluids when wiping

down the tester.

T5-600/T5-1000

Electrical Tester

Equipment Required for Performance Tests

The following equipment is required for performance tests:

•Fluke 5500A Multi-Product Calibrator, or equivalent

•0 V to 5 V adjustable dc power supply

•Approximately 8 m (26 ft) of #14 single-conductor magnet wire wound into a butterfly-shaped coil.

Figure 1 shows how to make the coil.

Performance Tests

Use the following procedures to verify the tester’s performance. If the tester fails any of the tests, return it to

Fluke for calibration or repair.

Testing the AC Current Function

The tests in this section require the butterfly coil shown in Figure 1. Note that the 10 conductors in the middle

of the coil cause the tester to read 10 times more current than the calibrator supplies.

1. Put one edge of the butterfly coil in a vice to hold the coil during testing.

2. Set the calibrator to the current and frequency given in Step 1 of Table 1.

3. Connect the butterfly coil to the calibrator.

4. Set the tester to the amperage function.

5. Place the tester’s current fork around the middle of the coil so that the alignment marks are centered and

perpendicular to the wire bundle, as shown in Figure 1.

6. Verify that the tester reads within the display limits shown for Step 1 in Table 1.

7. Apply the currents and verify the tester’s readings for the remaining steps in Table 1.

Table 1. AC Current Tests

Step Calibrator output T5-600/T5-1000 Display Limits

1 10 A, 60 Hz 96.7 to 103.3

2 10 A, 45 Hz 96.7 to 103.3

3 0.5 A, 45 Hz 4.5 to 5.5

Service Information

Performance Tests

21 cm

(~8.25")

10 turns of #14

single-conductor

magnet wire Separate into two 5-turn coils.

Use cable ties to

hold coils together

Connect to Calibrator

Mount Banana

plugs on wire end

qp7f.eps

Figure 1. Making the Butterfly Coil

T5-600/T5-1000

Electrical Tester

Testing the Voltage Functions

The tests in this section check the following voltage functions:

•Automatic selection of ac or dc voltage mode

•Correct operation of the hazardous voltage indicator

•Correct operation of the HOLD function

Perform the tests as follows:

1. Set the calibrator to the T5-600 or T5-1000 test voltage given in Table 2.

2. Apply the voltage to the tester. Verify that the tester reads within the display limits shown.

3. Apply the voltages and verify the tester’s readings for the steps in Tables 3 and 4.

Table 2. AC Voltage Test

T5-600 T5-1000

Calibrator Output T5-600 Display Limits

(AC annunciator ON) Calibrator Output T5-1000 Display Limits

(AC annunciator ON)

600 V, 60 Hz 589 to 611 1000 V, 60 Hz 983 to 1017

Table 3. DC Voltage Tests

T5-600 T5-1000

Step Calibrator Output T5-600 Display Limits

(DC annunciator ON) Calibrator Output T5-1000 Display Limits

(DC annunciator ON)

1 600 V dc 593 to 607 1000 V dc 989 to 1011

2 -60 V dc -58 to -62 -100 V dc -98 to -102

3 1.0 V dc 1 ±1* 1.0 V dc 1 ±1*

4 -1.0 V dc -1 ±1* -1.0 V dc -1 ±1*

* Verify that the ac annunciator is OFF.

Table 4. Hazardous Voltage LED and HOLD Function Tests

Step Calibrator Output T5-600/T5-1000 Display Indicators

1 12 V, 60 Hz Reading: 12 ±1

Hazardous voltage LED OFF

2 12 V, 60 Hz

Tap tester’s HOLD button Reading: 12 ±1

Hazardous voltage LED OFF

HOLD indicator ON

3 +31 V dc Reading: 12 ±1

Hazardous voltage LED ON

HOLD indicator ON

Service Information

Parts and Accessories

Resistance and Continuity Function Tests

1. Set the calibrator to the resistance given in Step 1 of Table 5.

2. Apply the resistance to the tester. Verify that the tester reads within the display limits shown.

3. Apply the resistances and verify the tester’s responses for the remaining steps in Table 5.

Table 5. Resistance and Continuity Tests

Step Calibrator Output T5-600/T5-1000 Display Limits and Beeper Responses

11kΩ988 to 1012

2 50 ΩBeeper ON

3 300 ΩBeeper OFF

40Ω-2 to 2

Low Battery Indicator Test

The following procedure verifies correct operation of the low battery indicator.

1. Remove the tester’s batteries.

2. Set the dc power supply to 3.0 V. Apply this voltage to the tester’s battery terminals.

3. Set the calibrator to 1 kΩ. Apply this resistance to the tester’s probes.

4. Slowly decrease the dc voltage just until the tester’s low battery indicator (M) turns on.

5. Verify that the tester reads 1000 ±12 counts (988 to 1012).

6. Disconnect the calibrator and the dc power supply. Reinstall the tester’s batteries.

Parts and Accessories

Tables 6 shows the replacement parts and accessories available from Fluke for the T5-600 and T5-1000

Electrical Testers.

Table 6. Replacement Parts and Accessories

Description Fluke Part Number

Test lead assembly

Replace only with Fluke double-insulated leads. 648029

Battery door 648144

Battery door screw 643830

AA battery, 1.5 V, carbon-zinc (2 required) 650181

AA battery, 1.5 V, alkaline (2 required) 376756

T5-600/T5-1000 Electrical Tester Instruction Sheet

English, French, Spanish, Portuguese 688355

T5-600/T5-1000

Electrical Tester

Table 6. Replacement Parts and Accessories (continued)

Description Fluke Part Number

T5-600/T5-1000 Electrical Tester Instruction Sheet

English, French, German, Italian, Finnish, Dutch 688371

T5-600/T5-1000 Electrical Tester Instruction Sheet

English, Norwegian, Swedish, Spanish, Portuguese 688374

T5-600/T5-1000 Electrical Tester Instruction Sheet

English, Korean, Japanese, Thai, Simplified Chinese, Traditional Chinese 688366

H5 Belt Holster Accessory

TP1 Probe Set, Flat Blade Accessory

TP4 Probe Set, 4 mm Round Accessory

Battery Replacement

Figure 2 shows how to replace the batteries. Observe the polarity markings inside the battery compartment.

qp1f.eps

Figure 2. Replacing the Batteries

Altri manuali per T5-600

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Fluke Apparecchiature di prova

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente