FMI B36I Guida rapida

For more information, visit www.fmiproducts.com

SAVE THIS BOOK

This book is valuable. In addition to instructing you

on how to install and maintain your appliance, it also

contains information that will enable you to obtain re-

placementpartsoraccessoryitemswhenneeded.Keep

it with your other important papers.

This ﬁreplace is approved for use as a wood burning ﬁre-

place or for use with a vented gas log approved to ANS

Z21.60, Z21.84 standards or for use with a vent-free gas log

heater approved to ANS Z21.11.2 standard. A FMI PROD-

UCTS, LLC hood must be installed when using a vent-free

log heater (see Accessories, page 18).

This wood burning ﬁreplace complies with UL127-

CAN/ULC-S610-M87 standard as a FACTORY BUILT

APPLIANCE.

FOR CANADA: The authority having jurisdiction (such

as the municipal building department, ﬁre department,

etc.) should be contacted before installation to deter-

mine the need to obtain a permit.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

WOOD BURNING FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

MODELS (V)B36, (V)B36I, (V)B36L, AND (V)B36LI

ICC-ES #ESR-2542

PFS

USC

www.fmiproducts.com 109034-01H2

SAFETY

WARNING: Do not install a

ﬁreplaceinsertinthisboxunless

themanufacturer'sinstructions

with the insert speciﬁcally state

thisﬁreplacehasbeentestedfor

use with this insert.

FOR YOUR SAFETY

• Do not store or use gasoline

oranyotherﬂammablevapors

orliquidsinthevicinityofthis

or any other appliance.

• Due to high temperatures, the

appliance should be located

out of trafﬁc and away from

furniture and draperies.

• Do not place clothing or other

ﬂammablematerialsonornear

the appliance.

• Never leave children unat-

tended when a ﬁre is burning

in the ﬁreplace.

WARNING: Use solid wood

or processed solid fuel ﬁre logs

only. When processed wood

fuel ﬁre logs are used, do not

poke or stir the logs while they

are burning. Use only ﬁre logs

that have been evaluated for

the application in ﬁreplace and

refer to ﬁre log warnings and

caution markings on packaging

prior to use.

This ﬁreplace is not intended to

beusedasasubstituteforafur-

nacetoheatanentirehome.Use

for supplemental heat only.

WARNING: Improper instal-

lation, adjustment, alteration,

service or maintenance can

causeinjury,propertydamageor

loss of life. Refer to this manual

for assistance or additional in-

formation. Consult a qualiﬁed

installer or local distributor.

IMPORTANT:Checklocalcodes

before installing this ﬁreplace.

Before beginning installation of this ﬁreplace,

read these instructions through completely.

• This FMI PRODUCTS, LLC ﬁreplace and

its components are safe when installed

according to this installation manual.

Unless you use FMI PRODUCTS, LLC

components, which have been designed

and tested for the ﬁreplace system, you

may cause a ﬁre hazard.

• The FMI PRODUCTS, LLC warranty will

be voided by and FMI PRODUCTS, LLC

disclaimsanyresponsibilityfor the following

actions.

a.Modification of the fireplace, com-

ponents, doors, air inlet system and

damper control.

b. Use ofany componentpartnotmanufac-

tured or approved by FMI PRODUCTS,

LLC in combination with a FMI PROD-

UCTS, LLC ﬁreplace system.

Proper installation is the most important step

in ensuring safe and continuous operation of

ﬁreplace. Consult the local building codes as

tothe particularrequirements concerned with

the installation of all factory built ﬁreplaces.

TABLE OF CONTENTS

Safety .................................................................. 2

Speciﬁcations ...................................................... 3

Fireplace Installation............................................ 4

Venting Installation .............................................. 7

Optional Gas Line Installation............................ 13

Operation and Maintenance.............................. 14

Technical Service............................................... 15

Parts.................................................................. 16

Replacement Parts............................................ 18

Accessories....................................................... 18

www.fmiproducts.com

109034-01H 3

SPECIFICATIONS

8.125"

12.875"

10.188"

9.625"

37.25"

33"

38"

36"

21.5" 32"

6.75"

34.75"

14.438"

19.375"

14"

38"

1.75"

0.750"

22.5"

21.125"

0" TO

BOTTOM

OUTSIDE AIR

(LEFT SIDE

ONLY)

TOP SPACERS

0.75" AIR

SPACE

BACK AND

SIDES

HEARTH

EXTENSION

52" X 16"

12"

EACH SIDE

NOT LESS

THAN 14" TO

PERPENDICULAR

SIDEWALL

1" AIRSPACE

TO COMBUSTIBLE

COMBUSTIBLE

WALL BOARD

0" TO

MATERIAL NO COMBUSTIBLE

MATERIAL ON FACE

SQUARE CHASE-TOP

TERMINATION

GAS LINE

KNOCK OUT

AIR KIT KNOCK OUT

ROUND TOP TERMINATION

www.fmiproducts.com 109034-01H4

FIREPLACE INSTALLATION

SELECTING LOCATION

Todeterminesafestand most efﬁcientlocation

forﬁreplace, you must take intoconsideration

the following guidelines:

1. Locationmust allow forproper clearances

(see Figures 1 and 2).

2. Consider a location where ﬁreplace will

not be affected by drafts, air conditioning

ducts, windows or doors.

3. A location that avoids cutting of joists or

roof rafters will make installation easier.

4. An outside air kit is available with this

ﬁreplace (see Optional Outside Air Kit on

page 7).

MINIMUM CLEARANCE TO

COMBUSTIBLES

Back and sides of ﬁreplace 3/4" minimum*

Floor** 0" minimum

Perpendicular wall to opening 14" minimum

Top spacers 0" minimum

Mantel clearances see Mantels, page 6

Chimney outer pipe surface 1" minimum

* Not required at nailing ﬂanges

** See step 2 of Framing

WARNING: Do not pack re-

quiredairspaceswithinsulation

or other materials.

Minimum/Maximum Chimney Height

Minimum height of chimney, measured from

base of ﬁreplace to ﬂue gas outlet of termina-

tion, is 11.5 feet for straight ﬂue or a ﬂue with

one elbow set. Maximum distance between

elbows is 2 feet. For systems with two elbow

sets, minimum height is 22 feet. Maximum

heightof any systemis 50 feet.Thismeasure-

mentincludesﬁreplace,chimneysections and

height of termination assembly at level of ﬂue

gas outlet (see Figure 18, page 11).

FRAMING

1. Frameopening for ﬁreplace using dimen-

sions shown in Figures 1 and 2.

2. If ﬁreplace is to be installed directly on

carpeting, tile (other than ceramic) or any

combustible material other than wood

ﬂooring, ﬁreplace must be installed upon

ametal or woodpanel extending fullwidth

and depth of ﬁreplace.

22"

37.625"

38.25"

Figure 1 - Framing Dimensions

47 3/8"

13 3/4"

19 1/2"

66 7/8"

Maintain 3/4"

Clearance at

Sides and

Back of

Fireplace

3/4" Clearance Not

Required at Nailing Flanges

Figure 2 - Corner Installation

3. Set ﬁreplace directly in front of this open-

ingand slide unitbackuntil nailing ﬂanges

touch side framing.

4. Check level of ﬁreplace and shim with

sheet metal if necessary.

5. Before securing fireplace to prepared

framing, ember protector must be placed

between hearth extension (not included)

and under bottom front edge of ﬁreplace

to protect against glowing embers falling

through. If ﬁreplace is to be installed on

a raised platform, a Z-type ember protec-

tor (not included) must be fabricated to

ﬁt your required platform height. Ember

protector should extend under ﬁreplace a

minimumof 1 1/2".Emberprotector should

be made of galvanized sheet metal (28

gauge minimum) to prevent corrosion.

6. Using screws or nails, secure ﬁreplace to

framing through ﬂanges located on sides

of ﬁreplace.

www.fmiproducts.com

109034-01H 5

HEARTH EXTENSION

A hearth extension projecting a minimum of

16" in front of and a minimum of 8" beyond

each side of ﬁreplace opening is required to

protect combustible ﬂoor construction in front

of ﬁreplace. Fabricate a hearth extension

using a material which meets the following

speciﬁcations: a layer of noncombustible,

inorganicmaterialhaving a thermalconductiv-

ity of K=0.84 BTU IN/FT, HR. F (or less) at 1"

thick. For example, if material selected has

a K factor of 0.25, such as glass ﬁber, the

following formula would apply:

0.25 x 1.0" = 0.30" thickness required

0.84

Thermal conductivity "K" of materials can be

obtained from manufacturer or supplier of

noncombustible material. If hearth extension

is to be covered, use noncombustible mate-

rial such as tile, slate, brick, concrete, metal,

glass, marble, stone, etc. Provide a means

to prevent hearth extension from shifting and

seal gap between ﬁreplace frame and hearth

extension with a noncombustible material

(see Figure 3).

WARNING:Hearthextension

is to be installed only as shown

in Figure 3.

FIREPLACE INSTALLATION

Continued

Figure 3 - Hearth Extension

Seal Gap

Fireplace Front

Ember Protector

Fireplace Front

Raised Hearth

Fireplace Front

Elevated

Ember Protector

Seal Gap

Hearth

Extension

Seal Gap

Fireplace Front

Ember Protector

Fireplace Front

Elevated

Do Not Block Louver

Ember Protector

Seal Gap

Hearth

Extension

Hearth Extension, Circulating Modes

Hearth Extension, Noncirculating Models

www.fmiproducts.com 109034-01H6

FIREPLACE INSTALLATION

Continued

Figure 4 - Mantel Clearances to

Combustible Material

Electrical

Bushing Electrical

Cover

Plate

Rocker

Switch

Figure 6 - Fan Switch-Electrical Bushing

Electrical

Housing Wire Nut (3x)

(Not Supplied) Outer Wrapper

of Fireplace

Electrical Cover

Plate and

Electrical Bushing

Fireplace Chassis

Ground

To Power

Source

Receptacle

(Supplied)

Power Source Wiring

(Not Supplied)

Prewired Receptacle

and Ground

MANTELS

A mantel may be installed if desired (see

Figure 4). Woodwork such as wood trims,

mantels or any other combustible material

projecting from front face must not be placed

within 9" of ﬁreplace opening (and within 9"

of top louver opening). Combustible materi-

als above 9" and projecting more than 1 1/2"

from ﬁreplace must not be placed less than

12" from top opening of ﬁreplace (NFPASTD

211, Sec. 7-3.3.3).

Mantels or any other combustible material

maycome up to side edgeof blackmetal face

of ﬁreplace if projection from front face falls

within limits shown in Figure 5.

12 1/4" Ref.

1 1/2"

Max.

Upper Section

of Circulating

Fireplace

Ref.

Min.

33°

3" Nom. *Note:Drawing

Not To Scale

Safe Zone For

Projection of

Combustible

Materials

Combustible

Material

12"

Min.

Fireplace Opening

Top of

Louvered

Opening

FAN/BLOWER KIT ASSEMBLY

Fanor blower kit is optionalwith this ﬁreplace

(for circulating models only). Use of blowers

or fans other than those manufactured by

FMI PRODUCTS, LLC voids warranty. Fan

is operated by pressing rocker switch (see

Figure6)inlower right hand cornerofﬁreplace

face. Blower is operated by turning control

knob (not shown).

Fan/blower kit electrical connections are

made through electrical cover plate on side

of ﬁreplace a shown in Figure 6.

FIREBOX

SAFE ZONE

Figure 5 - Side Mantel Clearance

Top View of Fireplace

Min. 12" from

Perpendicular Side Wall

0.625" Max.

33° 9"

Wiring Instructions

1. Remove electrical cover plate with bush-

ing from ﬁreplace by removing 2 sheet

metal screws as shown in Figure 6.

2. Slidepower sourcewiring through electri-

cal bushing opening and electrical cover

plate and make all necessary connec-

tions.

3. Slide all wiring connections in electrical

housing as shown in Figure 6.

4. Secure electrical cover plate with screws

previously removed.

Note:Electrical housingand coverplate have

sharp edges. Wear protective gloves.

Sheet

Metal

Screws

www.fmiproducts.com

109034-01H 7

Figure 8 - Lineal Gain

LINEAL GAIN

PART NO. DESCRIPTION GAIN

36" Fireplace 37 1/2"

12-8DM

12-8HT Pipe Section 10 5/8"

18-8DM

18-8HT Pipe Section 16 5/8"

24-8DM

24-8HT Pipe Section 23 5/8"

36-8DM

36-8HT Pipe Section 34 5/8"

48-8DM

48-8HT Pipe Section 46 5/8"

RT-8DM

RT-8HT Round Termination 6 7/8"*

RTL-8DM

RTL-8HT Round Termination 7 3/4"*

RTT-8DM

RTT-8HT Round Termination

with Slip Section 6 7/8" to

23 1/8"*

RTTL-8DM

RTTL-8HT Round Termination

with Slip Section 8 1/2" to

21 1/2"*

ET-8DM

ET-8HT Square Chase-Top 12"*

ETO-8DM Square Chase-Top

with Mesh 12"*

ETL-8DM

ETL-8HT Square Chase-Top

with Slip Section 7" to 15"*

ETLO-8DM Square Chase-Top

with Mesh & Slip

Section

12" to

25 1/2"*

* The lineal gain for the terminations is mea-

sured to the ﬂue gas outlet height.

Hemmed

End

8" Stainless

Inner Pipe

12 3/8"

Galvanized

Outer Pipe

Figure 7 - Outside Air Kit

Secure to Collars with Metal Tape, Screws

or Straps (Min. of 1/4" x 20" in size)

Air Inlet

Location

Must Allow

For Bushes

or Snow

Vent Hood

Required for

Wall Installation

Air Inlet

Eyebrow

Vented Crawl Space

(Check Local Codes

Before Installing in a

Vented Crawl Space)

VENTING INSTALLATION

OPTIONAL OUTSIDE AIR KIT

(MODEL AK4/AK4F)

Installation of outside air kit should be per-

formed during rough framing of ﬁreplace due

to the nature of it's location. Outside combus-

tion air is accessed through a vented crawl

space (AK4F) or through a sidewall (AK4).

See Figure 24 on page 15 for instruction of

operating air kit.

CAUTION: Combustion air

inlet ducts shall not terminate

in attic space.

The maximum height for the

air vent can not exceed 3 feet

below the ﬂue gas outlet of the

termination.

CHIMNEY PIPE

FMI PRODUCTS, LLC chimney system

consists of 12", 18", 24", 36" and 48" snap-

lock, double-wall pipe segments, planned

for maximum adaptability to individual site

requirements. Actual lengths gained after ﬁt-

tingoverlapsmust be takeninto consideration

(lineal gain) and are given in lineal gain chart

(see Figure 8).

Lineal gain is actual measurable length of a

part after two or more parts are connected.

WARNING: The opening in

collar around chimney at top of

ﬁreplacemustnotbeobstructed.

Neveruseblowninsulationtoﬁll

chimney enclosure.

www.fmiproducts.com 109034-01H8

VENTING INSTALLATION

Continued

Figure 9 - Typical Offset Installation

Return

Elbow

Offset

Elbow

Return

Elbow Offset

Elbow

6' Max.

Return

Elbow

Offset

Elbow

Offset

Elbow

Return

Elbow

AB C

Offset

Elbow

Ceiling

Support Pipe

12S-8DM

Return

Elbow

ASSEMBLY AND INSTALLATION OF

DOUBLE WALL CHIMNEY SYSTEM

Each double wall chimney section consists

of a galvanized outer pipe, a stainless steel

inner ﬂue pipe and a wire spacer. Pipe sec-

tions must be assembled independently as

chimney is installed. When connecting chim-

ney directly to ﬁreplace, inner ﬂue pipe sec-

tion must be installed ﬁrst with lanced side

up. Outer pipe section can then be installed

over ﬂue pipe section with hemmed end up.

Pressdown on each pipe section until lances

securely engage hem on ﬁreplace starter.

Wire will assure proper spacing between

inner and outer pipe sections.

Note: For Canada, use chimney parts des-

ignated HT.

Opening in collar around

chimneyattopofﬁreplacemust

not be obstructed. Never use

blown insulation to ﬁll chimney

enclosure.

Continue to assemble chimney sections as

outlined, making sure that both inner and

outerpipesections are lockedtogether.When

installing double wall snap-lock chimney to-

gether, it is important to assure joint between

chimney sections is locked. Check by pulling

chimney upward after locking. Chimney will

not come apart if properly locked. It is not

necessary to add screws to keep chimney to-

gether (exception - see Figure 11, page 9).

USING ELBOW OFFSETS (30E-8DM)

1. To achieve desired offset, you may install

combinations of 12", 18", 24", 36" and

48" length of double wall pipe (see offset

chart, page 7, and Figure 9).

Note:Forsystems with 2elbow sets, mini-

mum height is 22 feet. Maximum height

for any system is 50 feet.

2. Chimney weight above offset rests on

return elbow. Straps must be securely

nailed to rafters or joists (see Figure 10,

details A and B, page 9).

3. Maximumlengthofpipe between supports

(return elbow or 12S-8DM) is 6' of angle

run.Maximumof two 6'angle run sections

per chimney system (see Figure 9).

4. All pipe connections between offset and

return must be secured with two screws

on outer pipe only (see Figure 11, page

9). Do not penetrate inner stainless.

www.fmiproducts.com

109034-01H 9

Figure 11 - Elbow Offset

Screws

Figure 10 - Ceiling Support Pipe 12S-8DM

OFFSET RISE CHIMNEY LENGTH

A B 48" 36" 24" 18" 12"

4 3/8" 16 3/8" ELBOW SET ONLY

9 3/4" 25 1/2"1

12 3/4" 30 3/4"1

15" 34 3/4"1

18" 40" 1 1

21 1/4" 46 1/4"1

23 3/4" 49 1/4"11

27 3/4" 56 3/4"1

30" 60 3/4"1 1

33" 66" 1 1

36" 71" 1 1

38 1/4" 75" 2

41 1/4" 80 1/4"1 11

45" 86 3/4"2

46 3/4" 89 1/2"1 1 1

51" 97" 1 1

53 1/4" 101" 2 1

56 1/4" 106 1/4"2

59 1/4" 111 1/2"1 1 1

61 3/4" 115 1/2"2 1

64 3/4" 120 3/4"2 1

68 1/4" 127" 1 2

70" 130" 2 1 1

74 1/4" 137 1/2"1 2 1

76 3/4" 141 1/2"1 2 1

79 3/4" 146 3/4"4

OFFSET CHART (22-50 FT. SYSTEM HEIGHT)

2" Min.

Straps Straps

Straps

Detail A

Return Elbow Detail B

Angle

Firestop

See Detail A

See Detail B

Ceiling Support

Pipe 12S-8DM

VENTING INSTALLATION

Continued

www.fmiproducts.com 109034-01H10

VENTING INSTALLATION

Continued

(36.5 cm)

30"

(76.2 cm)

(2.5

cm)

(2.5

cm)

Minimum Measurements

(2.5 cm)

Opening "A"

Pitch Slope Opening

"A" Max. Used Flashing

Model No.

Flat 0° 15" V6F-8DM

0-6/12 26.6° 16 1/8" V6F-8DM

6/12- 12/12 45.0° 20 3/8" V12F-8DM

4. Remove shingles around opening mea-

sured. Cut out this section.

5. Add next sections of pipe until end

penetrates roof line. Check to see that

properclearancesare maintained. Extend

chimney by adding sectionsof double wall

pipe until pipe is minimum of 30" above

highest point of roof cutout. Termination

and chimney must extend a minimum of

36" above highest point where it passes

through roof.

Figure 14 - Roof Opening Measurements

FLASHING INSTALLATION (V6F-

8DM OR V12F-8DM)

Determineﬂashing to be used with roof open-

ingchart. Slide ﬂashing over pipeuntil baseis

ﬂatagainstroof. Replace asmany shingles as

needed to cover exposed area and ﬂashing

base. Secure in position by nailing through

shingles (see Figure 15, page 11). DO NOT

NAIL THROUGH FLASHING CONE.

Installing Flashing on a Metal Roof

When installing ﬂashing on a metal roof, it

is required that putty tape be used between

ﬂashing and roof. Flashing must be secured

toroof using #8x 3/4" screwsand then sealed

with roof coating to prevent leakage through

screw holes. A roof coating must also be ap-

plied around perimeter of ﬂashing to provide

a proper seal.

FIRESTOP SPACERS (3600FS-8DM-1)

Firestop spacers are required at each point

where chimney penetrates a floor space.

Their purpose is to establish and maintain

required clearance between chimney and

combustible materials. When pipe passes

through a framed opening into a living space

above, ﬁrestop must be placed onto ceiling

from below as shown in Figure 12.

They also provide complete separation from

one ﬂoor space to another or attic space as

required by most codes. When double wall

pipe passes through a framed opening into

an attic space, ﬁrestop must be placed into

an attic ﬂoor as shown in Figure 13.

Figure 12 - Firestop Spacer with Living

Space Above Ceiling

Figure 13 - Firestop Spacer with Attic

Space Above Ceiling

PENETRATING ROOF

Tomaintaina2"clearanceto pipe onaroofwith

a pitch, a rectangular opening must be cut.

1. Determine center point where pipe will

penetrate the roof.

2. Determine center point of the roof. Pitch

isthe distance the roof dropsover agiven

span,usually 12".A6/12pitchmeans that

the roof drops 6" for each 12" measure

horizontally down from roof rafters.

3. Use roof opening chart (Figure 14) to

determine correct opening length and

ﬂashing required.

If area above is a living space, install

ﬁrestop below framed hole.

If area above is an attic or insulated area,

install ﬁrestop above framed hole.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Manuali Camino da interno popolari di altre marche

Brigantia

Brigantia 35-DVRS31N-2 Manuale del proprietario

Nordpeis

Nordpeis Bergen Manuale utente

Superior

Superior BCT2536TMN Manuale utente

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuale utente

Renaissance

Renaissance RUMFORD 1000 Manuale utente

Lacunza

Lacunza IV-800 Manuale utente

Baxi

Baxi 940 Istruzioni per l’uso

Dru

Dru Maestro 60/2 Tall RCH Manuale utente

Diamond Fireglass

Diamond Fireglass SS-O22 Manuale utente

HearthStone

HearthStone Windsor Bay 8830 Manuale di programmazione

Napoleon

Napoleon ASCENT B42 Manuale utente

Enviro

Enviro E33GI Manuale utente

Smeg

Smeg L30 FABE Istruzioni di montaggio

KEDDY

KEDDY K700 Manuale utente

Godin

Godin 3451 Manuale utente

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuale utente

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuale utente

Desa

Desa CCFPDFT Manuale operativo