Fox-Lux REM10 Manuale utente
5m max.
1: Batteries 2: Infrared range
•This product should only be used by suitably qualified personnel.
•This product can be used to send commands to compatible Fox Lux self-test emergency luminaires
and conversion kits.*
•Please see below which functions are available for each version.
•It requires two AAA batteries.
*REM10 remote control adds new features to self-test emergency luminaires and it is an optional tool for those responsible for
emergency lighting installations. Note that self-test emergency luminaires work independently from the remote control.
REM10 can also be used to initiate a duration test on manual test luminaires - please contact Fox Lux for information.
Part number Description Operating
temperature Net weight
REM10 Remote Control 0 - 40°C 0.06 kg
15°
strip
Position yourself as close as possible to the luminaire and
point the remote control towards the luminaire when
pressing the buttons.
REM10 is requires two AAA batteries. Please remove the
battery insulating pull tab to start using.
REM10 EMERGENCY LIGHTING REMOTE CONTROL
T
hank you for purchasing our REM10 Remote Control. Our products have been designed according to
the relevant standards and if installed and maintained correctly will provide a long service life.
BS EN
60598-1 / BS EN 60598-2-22 / BS EN 50172 / BS EN 1838 / BS EN 62034 / ISO 7010 / ISO 3864
Ensure this product is disposed
responsibly according to WEEE
directive 2002/96/EC
t |
+44(0)1543
REM10 Remote Control
Functions:
MT
ON
TEST
AST
ON
BAT
CHK
AST
CHK
AST
OFF
MT
OFF
Functional test 1
Initiate full dur a t i
o n t e s
t 2
Interrupt full d
u r a t
i o
n
t e
s t 3
Disable se l
f
- t e s
t
f u
n c
t
i o n
Enable self-
t
e
s
t f
u
n
c
t
i
o
n 6
5
Self-test Check 7
Battery Check 4
1. Press "TEST " to carry out a Functional Test
2. Press "MT ON" to initiate a Full Duration Test*
3. Press "MT OFF" to interrupt Full Duration Test
4. Press "BAT CHK" to check status of battery’s health.**
5. Press "AST OFF" to disable self-test function
6. Press "AST ON" to enable self-test function
7. Press "AST CHK" to to verify status of self-test function
After each button press the indicator will flash
GREEN/RED
to acknowledge the command
* Note that when the Full Duration Test is completed the
batteries require up to 8 hours to be re-charged again.
** Note that battery status is recorded and updated after full
duration test is completed .
FUNCTIONS FOR “self-test” VERSIONS:
Flashing Codes for Self-test Check (Function 7)
Flashing Code for Battery Health Check (Function 4)
GREEN/RED
LED
Indicator
Battery Health/Status Check
Approx. Capacity Reserve
Battery Status
(emergency lighting duration)
duration > 3hr 30min
3hr 15min < duration < 3hr 30min
3hr < EM duration < 3hr 15min
Excess capacity > 16%
RED/GREEN
LED
Indicator
1x Green/Red
2x Green/Red
Self-Test Status check
Battery not yet tested
(status will be available after first full duration test)
-
Flashing Code
Self-test enabled
Self-test disabled
Self-test Status
Flashing Sequence
4x Green/Red
= Off
= On
= Slow flash 0.5Hz
= Normal flash 1Hz (once/second)
= Fast flash 2Hz (twice/second)
1x Green/Red
2x Green/Red
3x Green/Red
t |
+44(0)1543
Excess capacity < 16% > 8%
Excess capacity < 8% > 0%
lssue V1
5/1/2020
t
| +44(0)1543
396400
| e | [email protected]
|w| www.fox-lux.co.uk
Registered Office: Alex House 260/8 Chapel Street, Salford, Manchester, M3 5JZ
Company Registration No. 11821284 VAT Registration
No. 320 9921 12
Flashing Code for Fault Condition (Function 1)
GREEN/RED
LED
Indicator
Status Indication
Status OK - battery charged
Battery disconnected/duration test fail
Test in progress
Battery outside temperature range
Battery charging
REM10 Remote Control
Load/light source fault
Altri manuali Fox-Lux Telecomando
