Franke KEMWSBF Manuale utente

10112 036865-004

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

1. InSPEcTIOn

Inspect the cartons and various components for evidence of rough handling and concealed damage. Damage claims should be ﬁled

with the carrier.

2. InSTALLATIOn, PLUMBInG & ELEcTRIcAL cOnnEcTIOnS

a) NOTE: The following states require a licensed plumber to install cooler; AR, GA, MA, MI, OK, RI, SC, SD, TX, VT and WI. CA, KS, MN, NM and

OR allow for a state-registered installer or contractor as well. State and local plumbing codes may prohibit the use of saddle tapping valves

for water line connection in some applications. All connections must conform to applicable plumbing codes.

b) Plumbing rough-in and wall opening should be prepared as shown on roughing-in drawing.

c) FLUSH BUILDING WATER SUPPLY BEFORE INSTALLING UNIT.

d) Install drain receptor to frame with screws provided.

e) A 2X4 junction box is provided for the installation of a 115 volt receptacle. The bottle ﬁller is provided with a power cord with a grounded

NEMA 15 plug. It is recommended that ﬂexible conduit be used to supply power to the junction box and chiller if used. Check the electric

current available. Type and voltage must be the same as listed on the unit data plate.

f) Refer to the appropriate connection diagram for water and drain connections. Check for leaks.

g) The lower panel can be secured with the provided key locks or screws. The KEM8SBF features one lockable and one non lockable lower

panel, these are interchangeable.

MODELS WITH CHILLER

h) Attach cradle mounting angles to unit mounting cradle with 4 screws provided. Slide unit mounting cradle into frame and secure in place

with 4 screws, provided. (Cradle is used only when cooling unit is to be installed.) NOTE: BOTTOM FLANGE ON CRADLE IS TO

BE BEHIND FRAME FRONT FLANGE.

i) Slide cooling unit onto cradle.

KEM8SBF & KEM12SBF WITH FOUNTAIN

j) Install the fountain mounting plate to the frame assembly using the provided screws.

k) Place the upper panel in place on the frame top angle and fasten with 2 screws, provided, at the bottom.

l) Remove the bottom plate from the fountain arm. Save the screws.

m) Snap the reveal gasket over the back end of the fountain arm.

n) Add compression connector, furnished by others, to the fountain waste tube and slide back approximately 3" out of the way. Refer to the

appropriate connection diagram.

o) Hang the fountain on the mounting plate studs. NOTE: AS THE FOUNTAIN IS HUNG, FEED THE WASTE TUBE INTO THE WASTE STUB ON THE

WALL SIDE.

p) Tighten the fountain to the mounting plate with the 5/16 - 18 nuts and washers and the 1/4 - 20 bolts and washers provided.

q) Slide the reveal gasket(s) back into the notch between the panel and the arm. The gasket serves as an appearance item only (to close up any

opening around the panel and the mounting plate).

3. OVERLOAD PROTEcTIOn (SySTEMS WITh chILLER)

The compressor motor is equipped with an automatic reset protector which will disconnect the motor from the line in case of overload.

4. LUBRIcATIOn (SySTEMS WITh chILLER)

This unit is equipped with a hermetically sealed compressor. No additional lubrication is required. The fan motor installed on this unit

seldom needs oiling. If required, a few drops of SAE 10 oil should be used.

2036865-004 0112 30112 036865-004

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

5. TO DIScOnTInUE USE OF SySTEMS WITh chILLER

Drain cooler when removed from service: (1) Remove grille, (2) Close supply valve, (3) Provide container to catch water, and remove drain plug.

6. MAInTEnAncE (SySTEMS WITh chILLER)

The only maintenance required is the removal of dirt and lint from the condenser. Inspection should be made at 3 month intervals. Remove the grille

and clean the condenser with a vacuum attachment.

The warranty and the Underwriters’ Laboratory listing for this machine are automatically voided if this machine is altered, modiﬁed,

or combined with any other machine or device. Alteration or modiﬁcation of this machine may cause serious ﬂooding and/or hazardous electrical

shock or ﬁre. EXCEPT AS SET FORTH HEREIN, THE MANUFACTURER MAKES NO OTHER WARRANTY, GUARANTEE OR AGREEMENT EXPRESSED,

IMPLIED OR STATUTORY, INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

WARnInG

19 [483]

WALL OPENING

19 3/4

[502]

9 7/8

[251]

40 [1016]

WALL

OPENING

40 3/4

[1035]

28 3/8

[721]

3 15/16 [100]

5 5/16

[136]

WATER OUTLET

AND INLET

6 7/16 [164]

JUNCTION BOX

5/16 [8] DIA. MOUNTING

HOLES 8 EACH SIDE,

4 TOP AND 4 BOTTOM

1 13/16 [46]

1/2 [13]

11 5/16 [287]

WALL OPENING

8 1/8 [206]

2 [52]

1 1/2 OR 1 1/4

IPS WASTE

STUB OUT

1/4 OD TUBE

COOLING UNIT

WATER INLET

1 1/4 TAILPIECE

1 3/8 [35]

ELECTRICAL

CONNECTION

COOLING UNIT

FRAME ASSY

FURNISHED

FINISHED WALL

FLOOR LINE

3 1/2 [89]

4 5/16 [110]

21 9/16

[548]

21 3/8

[644]

26 5/8

[677]

ROUGHING-IN

AND

DIMENSIONAL DRAWING

THIRD ANGLE PROJECTION

NOTES:

1. RECOMMENDED ADULT HEIGHT INSTALLATION SHOWN.

ADJUST VERTICAL DIMENSIONS AS REQUIRED TO COMPLY

WITH FEDERAL, STATE AND LOCAL CODES.

2. STOP VALVE, TRAP, PIPE CONNECTOR TO WASTE

WASTE LINE NOT PROVIDED. SHORT RADIUS TRAP REQUIRED.

3. ALL DIMENSIONS ARE IN INCHES.

DIMENSIONS IN BRACKETS [ ] ARE IN MILLIMETERS.

MODULAR SPORTS BOTTLE FILLER - MODELS KEMWSBF, KEMW8SBF, KEMW12SBF

39 1/2

[1003]

38 3/4 [984]

WALL OPENING

19 3/4

[502]

9 7/8

[251]

REMOVE NUT AND BUTTON

FOR FLOW REGULATOR

ACCESS

3/8 O.D. WATER INLET

1 1/2 OR 1 1/4 IPS WASTE

STUB OUT 2[51] 3 [80]

TO ORIFICE

WATER OUTLET

AND INLET

5/16 [8] DIA. MOUNTING

HOLES 8 EACH SIDE,

8 TOP AND 8 BOTTOM

1 13/16 [46]

1/2 [13]

14 [356]

5 5/16 [136]

28 3/4

[730]

TO FTN

34 9/16

[878]

ORIFICE

[686]

FLOOR LINE

6 7/16 [164]

JUNCTION

BOX

COOLING

UNIT

1 1/4 OD TAILPIECE

1 3/8 [35] ELECTRICAL

CONNECTION

FINISHED WALL

[406]

18 1/2

[470]

1 1/2 OR 1 1/4

IPS WASTE

STUB OUT

6 1/2 [165]

10 13/16

[274]

40 3/4

[1035]

3 15/16 [100]

1 1/4 TAILPIECE

19 3/4

[502]

28 3/8

[721]

26 5/8

[677]

25 3/8

[644]

3 1/2 [89] FRAME

ALLOW ADDITIONAL

DEPTH FOR WATER

AND WASTE LINES

4 5/16 [110]

21 9/16

[548]

[1016]

WALL

OPENING

2 [52]

8 1/8

[206]

11 5/16 [287]

WALL OPENING

1/4 O.D TUBE

COOLING UNIT

WATER INLET

NOTES:

1. RECOMMENDED ADULT HEIGHT INSTALLATION SHOWN. ADJUST VERTICAL DIMENSIONS AS

REQUIRED TO COMPLY WITH FEDERAL, STATE AND LOCAL CODES.

2. STOP VALVE, TRAP, PIPE CONNECTOR TO WASTE, WASTE LINE NOT PROVIDED. SHORT RADIUS

TRAP REQUIRED.

3. ALL DIMENSIONS ARE IN INCHES. DIMENSIONS IN BRACKETS [ ] ARE IN MILLIMETERS.

THIRD ANGLE PROJECTION

ROUGHING-IN

AND

DIMENSIONAL DRAWING

MODULAR SPORTS BOTTLE FILLER - MODELS KEM8SBF, KEM12SBF

4036865-004 0112 50112 036865-004

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

BOTTLE FILLER ASSEMBLy WITh chILLER

WALL MOUNTING FRAME

SECURES INTO WALL

WITH FACE FLUSH WITH

FINISHED WALL

UV KIT (ACCESSORY)

(SEE STEP 9)

UPPER FRONT PANEL

MOUNTS TO FRAME

WITH BOTTOM SCREWS

SECURE CRADLE MOUNTING ANGLE TO

FRAME FLANGE USING SCREWS PROVIDED.

DO NOT TIGHTEN SCREWS. SLIDE CRADLE

BETWEEN ANGLES AND ATTACH TO ANGLES

WITH SCREWS PROVIDED. TIGHTEN ALL SCREWS.

OPTIONAL FILTER

(SEE STEP 6)

COOLING UNIT

MOUNTING CRADLE

CRADLE MOUNTING

ANGLES (2 PROVIDED)

COOLING UNIT (OPTIONAL)

MOUNTS INSIDE CRADLE

LOWER FRONT PANEL

MOUNTS TO FRAME

WITH BOTTOM SCREWS

OR OPTIONAL LOCKS

(2 PROVIDED) TRIM BEZEL (ACCESSORY)

(SEE STEP 11)

STEP 1: InSTALL MOUnTInG FRAME

a) Install frame per rough in drawing.

b) Install drain assembly.

c) Install Snap bushings.

STEP 2: KEMWSBF (WIThOUT chILLER)

a) Install provided ball valve and 3/8" O.D. copper tube to

building water supply.

b) Install tubing as shown before mounting the panel assembly.

c) Install upper panel assembly (Screws provided).

d) Install lower louver panel using strainer supplied locks or screws.

STEP 3: FILTER InSTALLATIOn (WIThOUT chILLER)

a) Mount ﬁlter clip to frame. (See Figure 2)

b) Install provided stem elbows.

Run water line from solenoid valve to bottle ﬁller delivery tube (See Figure 2).

d) Connect solenoid valve out to ﬁlter in.

e) Connect ﬁlter out to ﬁller delivery tube.

OUT

STRAINER

INSIDE

OUT

STEM

ELBOWS

DRAIN

ASSEMBLY

2X4 JUNCTION

BOX

MOUNTING

SCREW

(2 PROVIDED)

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

SNAP

BUSHINGS

OPTIONAL FILTER

LOCATION

LESS CHILLER

1/4" STEM

ELBOWS

(2 PROVIDED)

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4" TAILPIECE

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

PROVIDED

BALL VALVE AND

3/8" O.D. COPPER

TO BUILDING

WATER SUPPLY

FILLER DELIVERY

TUBE

INSULATED TUBE

CONNECTS TO

FILLER TUBE

SEE

STEP 3

FROM

SOLENOID

VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

OUT

STRAINER

INSIDE

OUT

STEM

ELBOWS

DRAIN

ASSEMBLY

2X4 JUNCTION

BOX

MOUNTING

SCREW

(2 PROVIDED)

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

SNAP

BUSHINGS

OPTIONAL FILTER

LOCATION

LESS CHILLER

1/4" STEM

ELBOWS

(2 PROVIDED)

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4" TAILPIECE

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

PROVIDED

BALL VALVE AND

3/8" O.D. COPPER

TO BUILDING

WATER SUPPLY

FILLER DELIVERY

TUBE

INSULATED TUBE

CONNECTS TO

FILLER TUBE

SEE

STEP 3

FROM

SOLENOID

VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

OUT

STRAINER

INSIDE

OUT

STEM

ELBOWS

DRAIN

ASSEMBLY

2X4 JUNCTION

BOX

MOUNTING

SCREW

(2 PROVIDED)

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

SNAP

BUSHINGS

OPTIONAL FILTER

LOCATION

LESS CHILLER

1/4" STEM

ELBOWS

(2 PROVIDED)

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4" TAILPIECE

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

PROVIDED

BALL VALVE AND

3/8" O.D. COPPER

TO BUILDING

WATER SUPPLY

FILLER DELIVERY

TUBE

INSULATED TUBE

CONNECTS TO

FILLER TUBE

SEE

STEP 3

FROM

SOLENOID

VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

Figure 1

Figure 2

Figure 3

6036865-004 0112 70112 036865-004

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

CHILLER

FRONT OF CHILLER

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4" TAILPIECE

PROVIDED BALL

VALVE AND 3/8" O.D.

COPPER TUBE

CONNECT TO

BUILDING WATER

SUPPLY

1/4" UNION

FTGS. PROVIDED

FILLER DELIVERY

TUBE

TO CHILLER OUT

OPTIONAL FILTER

LOCATION WITH

CHILLER

TO CHILLER IN

FILTER CLIP

PLACE FILTER

IN CLIP AS

SHOWN

FROM

SOLENOID

VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

STEM

ELBOWS

CHILLER

FRONT OF CHILLER

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4" TAILPIECE

PROVIDED BALL

VALVE AND 3/8" O.D.

COPPER TUBE

CONNECT TO

BUILDING WATER

SUPPLY

1/4" UNION

FTGS. PROVIDED

FILLER DELIVERY

TUBE

TO CHILLER OUT

OPTIONAL FILTER

LOCATION WITH

CHILLER

TO CHILLER IN

FILTER CLIP

PLACE FILTER

IN CLIP AS

SHOWN

FROM

SOLENOID

VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

STEM

ELBOWS

STEP 4: KEMW8SBF AnD KEMW12SBF (cOnnEcTInG ThE chILLER)

a) Attach cradle to frame per rough in drawing (Screws provided - 4).

b) Place chiller in frame.

c) Install 1/4" Union ﬁttings on chiller inlet and outlet.

d) Run the water line from the bottle ﬁller solenoid valve OUT to chiller IN.

Cut oﬀ excess and use it to run from chiller OUT to the bottle ﬁller

delivery tube.

STEP 5: FILTER LOcATIOn (WIThIn chILLER)

a) Screw ﬁlter clip to unit in location as shown in Figure 5 (Screw provided).

b) Install 1/4" stem elbows (provided) in ﬁler inlet and outlet.

c) Place ﬁlter in clip as shown in Figure 6.

STEP 6: FILTER InSTALLATIOn (WITh chILLER)

a) Mount ﬁlter to chiller casing (See Figure 6).

b) Install provided stem elbows.

c) Run the water line from the bottle ﬁller solenoid valve to the chiller inlet.

d) Connect bottle ﬁller solenoid valve to ﬁlter inlet.

e) Connect ﬁlter out to the chiller inlet.

CHILLER

FRONT OF CHILLER

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4" TAILPIECE

PROVIDED BALL

VALVE AND 3/8" O.D.

COPPER TUBE

CONNECT TO

BUILDING WATER

SUPPLY

1/4" UNION

FTGS. PROVIDED

FILLER DELIVERY

TUBE

TO CHILLER OUT

OPTIONAL FILTER

LOCATION WITH

CHILLER

TO CHILLER IN

FILTER CLIP

PLACE FILTER

IN CLIP AS

SHOWN

FROM

SOLENOID

VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

STEM

ELBOWS

STEP 7: chILLER AnD FOUnTAIn cOnnnEcTIOnS

(KEM8SBF, KEM12SBF)

a) Install chiller in frame.

b) Install 1/4" union on chiller IN.

c) Connect 1/4" union tee to chiller OUT.

d) Determine tube length needed to connect bottle ﬁller solenoid IN (The

line with the attached ball valve) to chiller tee. Cut tube and connect.

e) Attach remaining tube from ball valve to chiller IN.

f) Remove adapter ﬁtting and copper tube from the fountain water line.

Install provided 1/4" union.

g) Determine length of tube needed to connect bottle ﬁller solenoid OUT

to bottle ﬁller delivery tube, cut oﬀ excess.

h) Use excess tube to connect fountain to chiller tee.

STEP 8: FILTER cOnnEcTIOn (BOTTLE FILLER AnD FOUnTAIn)

a) Mount ﬁlter to chiller casing (See Figure 5).

b) Install provided stem elbows (See Figure 8).

c) Cut the tube to the chiller inlet.

Connect tubing from ball valve to ﬁlter IN. Connect ﬁlter OUT to chiller IN.

FRONT OF CHILLER

CHILLER

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4"

TAILPIECE

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

FILLER DELIVERY TUBE

1/4" UNION FITTING

1 1/4" TAILPIECE

(TRAP NOT INCLUDED)

1/4" UNION CHILLER

IN CONNECTS TO BALL

VALVE OF FILTER OUT

(IF USED)FITTINGS

PROVIDED

PROVIDED BALL

VALVE AND 3/8"

O.D. COPPER

TO BUILDING

WATER SUPPLY

1/4" UNION TEE

CHILLER OUT

CONNECT TO

FOUNTAIN AND

BOTTLE FILLER

SOLENOID IN

FILTER CLIP

PLACE FILTER

IN CLIP AS

SHOWN

STEM

ELBOWS

FROM PROVIDED

BALL VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

FRONT OF CHILLER

CHILLER

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4"

TAILPIECE

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

FILLER DELIVERY TUBE

1/4" UNION FITTING

1 1/4" TAILPIECE

(TRAP NOT INCLUDED)

1/4" UNION CHILLER

IN CONNECTS TO BALL

VALVE OF FILTER OUT

(IF USED)FITTINGS

PROVIDED

PROVIDED BALL

VALVE AND 3/8"

O.D. COPPER

TO BUILDING

WATER SUPPLY

1/4" UNION TEE

CHILLER OUT

CONNECT TO

FOUNTAIN AND

BOTTLE FILLER

SOLENOID IN

FILTER CLIP

PLACE FILTER

IN CLIP AS

SHOWN

STEM

ELBOWS

FROM PROVIDED

BALL VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

FRONT OF CHILLER

CHILLER

OUT

SOLENOID

VALVE OUT

SOLENOID

VALVE IN

1 1/4"

TAILPIECE

DRAIN

COMPONENTS

NOT INCLUDED

SHORT RADIUS

TRAP REQUIRED

FILLER DELIVERY TUBE

1/4" UNION FITTING

1 1/4" TAILPIECE

(TRAP NOT INCLUDED)

1/4" UNION CHILLER

IN CONNECTS TO BALL

VALVE OF FILTER OUT

(IF USED)FITTINGS

PROVIDED

PROVIDED BALL

VALVE AND 3/8"

O.D. COPPER

TO BUILDING

WATER SUPPLY

1/4" UNION TEE

CHILLER OUT

CONNECT TO

FOUNTAIN AND

BOTTLE FILLER

SOLENOID IN

FILTER CLIP

PLACE FILTER

IN CLIP AS

SHOWN

STEM

ELBOWS

FROM PROVIDED

BALL VALVE

TO BOTTLE

FILLER DELIVERY

TUBE

Figure 4

Figure 5

Figure 6

Figure 7

Figure 5

Figure 8

8036865-004 0112 90112 036865-004

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

STEP 9: UV KIT - InSTALLATIOn GUIDE (BAcK VIEW WITh chILLER,

UV, AnD FILTER)

a) Remove lower and upper front panels, if needed.

b) Screw UV housing clip to frame (only one clip required). Holes provided

in frame upper left side (Figure 9 - BACK VIEW).

c) Install inter connecting water ﬁtting to UV housing, provided. Refer to

Figure 10 and 11 for details.

Install quartz sleeve with O-Ring into UV housing. Assemble retainer

nut - do not over tighten refer to Figure 10 for details.

e) Run UV power cord connection through hole provided in frame. Connect

UV bulb to power supply cord and insert bulb into UV housing. See Figure

9 and 10 for details.

STEP 10: UV KIT - InSTALLATIOn GUIDE

a) CAUTION - Carefully swap UV housing into clip installed in STEP 9.

The UV bulb and quartz sleeve are made of glass and are fragile.

Use CAUTION in this step to avoid damaging these parts.

b) Connect all interconnecting water lines. See water circuit illustration on

next page.

c) Re-connect electrical power and install upper and lower front panels.

INLET

OUTLET

INLET

OUTLET

HOLE PROVIDED

FOR ELECTRICAL

AND WATER RUN

FILLER DELIVERY TUBE

SOLENOID VALVE

SEE FIG. 11

FOR DETAILS

UV HOUSING

QUARTZ SLEEVE

AND O-RING

RETAINER NUT

UV LAMP

POWER SUPPLY

AND CONNECTOR

1/4" X 3/8"

REDUCER

3/8" X 1/2"

REDUCER

1/2" X 1/2"

ELBOW

INLET

OUTLET

INLET

OUTLET

HOLE PROVIDED

FOR ELECTRICAL

AND WATER RUN

FILLER DELIVERY TUBE

SOLENOID VALVE

SEE FIG. 11

FOR DETAILS

UV HOUSING

QUARTZ SLEEVE

AND O-RING

RETAINER NUT

UV LAMP

POWER SUPPLY

AND CONNECTOR

1/4" X 3/8"

REDUCER

3/8" X 1/2"

REDUCER

1/2" X 1/2"

ELBOW

INLET

OUTLET

INLET

OUTLET

HOLE PROVIDED

FOR ELECTRICAL

AND WATER RUN

FILLER DELIVERY TUBE

SOLENOID VALVE

SEE FIG. 11

FOR DETAILS

UV HOUSING

QUARTZ SLEEVE

AND O-RING

RETAINER NUT

UV LAMP

POWER SUPPLY

AND CONNECTOR

1/4" X 3/8"

REDUCER

3/8" X 1/2"

REDUCER

1/2" X 1/2"

ELBOW

SOLENOID VALVE

PROVIDED. SEE FIG.

2 IN STEP 2 OF THESE

INSTRUCTIONS.

BALL VALVE AND

3/8" O.D. COPPER

TO BUILDING

WATER SUPPLY.

FILTER ASSEMBLY

(OPTIONAL)

ATTACHED TO FILLER

DELIVERY TUBE. SEE

FIG. 2 IN STEP 2 OF

THESE INSTRUCTIONS.

REMOTE CHILLER

(OPTIONAL)

UV HOUSING

AND BALLAST

NOTE:

IF OPTIONAL FILTER ASSEMBLY IS NOT INSTALLED,

CONNECTION "A" WILL CONNECT TO LOCATION "AA" OF

THE UV ASSEMBLY.

IF OPTIONAL REMOTE CHILLER IS NOT INSTALLED,

CONNECTION "B" WILL CONNECT TO LOCATION "BB" OF

THE UV ASSEMBLY.

UV KIT - WATER cIRcUIT

Figure 9

(BAcKVIEW)

Figure 10

Figure 11

10 036865-004 0112 110112 036865-004

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

STEP 11: TRIM BEZEL InSTALLATIOn

a) Install frame assembly to a ﬂat surface. Use appropriate fastening hardware (not included). Refer to the ﬁrst 2 pages of this instruction

package for the correct installation height.

b) Remove bottom plate from trim bezel (4 Screws).

c) Install trim bezel to frame assembly and replace bottom plate with screws.

d) Install drain assembly, snap bushings and any other accessories included with this kit.

e) Install upper and lower front panel.

TRIM BEZEL

FRAME ASSEMBLY

UPPER AND LOWER

FRONT PANELS

FASTENING POINTS

ON FRAME

TRIM BEZEL BOTTOM

PLATE WITH SCREWS

TRIM BEZEL InSTALLATIOn

2 REQ’D

4 REQ’D

3 REQ’D

2 REQ’D

FLOW RESTRICTOR

THIS FLOW RESTRICTOR IS INTENDED TO MAKE YOUR WATER

FLOW AT THE PROPER RATE.

- PRESS THE FLOW RESTRICTOR FIRMLY INTO THE

TUBING PROVIDED.

- INSERT THE TUBING WITH THE FLOW RESTRICTOR INTO ELBOW

FITTING AT THE TOP FITTING OF THE SOLENOID VALVE.

ILLUSTRATED PARTS BREAK DOWn

Figure 12

036865-004 0112

Franke Kindred Canada Limited

1000 Franke Kindred Road

Midland, ON L4R 4K9

CANADA

Tel. 1-866-687-7465

Fax 1-800-361-8408

www.franke-commercial.com

MODULAR SPORTS BOTTLE FILLER

InSTRUcTIOnS FOR MODELS: KEMWSBF, KEMW8SBF, KEMW12SBF,

KEM8SBF, KEM12SBF

2 REQ’D

6 REQ’D

“SERIAL

& DATA

LABEL”

2 REQ’D

1 027624-401 PANEL, BOTTLE FILLER UPPER 1

2 027697-005 PANEL, KEMWSBF LOWER LOUVER STN 1

3 034649-001 SPRING, MSBF 1

4 036190-001 ALCOVE, MSBF 1

5 036191-001 DRAIN, MSBF 1

6 036192-001 GRILLE, MSBF 1

7 036194-001 BUTTON, MSBF 1

8 036195-001 MOUNT, SWITCH 1

9 036197-001 SHELF, ACTIVATION MSBF 1

10 026642-003 SCREW, HEX HD TAPPING 14

11 026675-003 SCREW, FLAT HD TAPPING 3

12 201828-01 SOLENOID VALVE 120V/50-60HZ 1

13 030939-002 LABEL, WIRING DIAGRAM MSBF 1

14 029994-103 FTG, JG. ELBOW, PLUG IN WHI 1

15 019008 BUSHING, STRAIN RELIEF SR6P34 1

16 029139-001 FTG, JG. ELBOW, PLUG IN 1

17 026630-039 SCREW, PAN HD TAPPING TYPE AB 1

18 036207-001 COVER, ACTIVATION SHELF 1

19 036208-001 TUBE, FILL 1

20 028913-001 FTG, JG. BULKHEAD UNION 3/8 1

21 024070-006 TIE, CABLE 6" 1

22 029583-005 LABEL GROUP, CARTON & UNIT 1

23 026210 ANGLE, CRADLE MTG 2

24 027270-003 BAG, PLASTIC 1

25 026642-023 SCREW, HEX HD TAPPING 2

26 020850-004 INSERT, N’PLATE FRANKE GEL BA 1

27 031657-004 LOCK ASSY WITH CAM 2

28 031657--005 WASTER FOR COMPK BF 2

29 036466-001 PACKAGING GROUP BF 1

30 036471-001 ELEC CKT DWG W/ LEAD WIRE P/N 1

31 036470-001 KIT, BF ACCESSORIES 1

32 026660-006 SCREW, RD HD MACHINE 1

33 026824-006 NUT, HEX 1

34 0211413 LOCKWASHER, EXTERNAL TOOTH 1

35 030973-003 TIMER, SOLID STATE 60 SEC 1

36 026670-028 SCREW, HEX HD MACHINE 1

ILLUSTRATED PARTS BREAK DOWn cOnTInUED Items not shown: 23, 24, 29, 30, 31, 37

PART # DEScRIPTIOn qTy PART # DEScRIPTIOn qTy

Questo manuale è adatto per i seguenti modelli

Altri manuali Franke Distributore

Franke

Franke RODAN RODX618E Manuale utente

Franke

Franke 2030022936 Manuale utente

Franke

Franke RODX672E Manuale utente

Franke

Franke SD01-001SFL Manuale utente

Franke

Franke EXOS618X Manuale utente

Franke

Franke RODX672 Manuale utente

Franke

Franke STRATOS STRX635B Manuale utente

Franke

Franke SD99-009 Manuale utente

Franke

Franke RODX619E Manuale utente

Franke

Franke RODX616 Manuale utente

Franke

Franke F3D3S Manuale utente

Franke

Franke RODAN RODX672 Manuale utente

Franke

Franke RODX600TT Supplemento

Franke

Franke EXOS625EX Manuale utente

Franke

Franke F3D3S Manuale utente

Franke

Franke RODX191 Manuale utente

Franke

Franke RODAN RODX637 Manuale utente

Franke

Franke STRATOS STRX627 Manuale utente

Franke

Franke STRX630 Manuale utente

Franke

Franke EXOS Series Manuale utente

Franke

Franke RODAN RODX600ME Manuale utente

Franke

Franke EXOS618X Manuale utente

Franke

Franke F3Dn Twin Manuale utente

Franke

Franke 7612210006425 Manuale utente

Manuali Distributore popolari di altre marche

Silver King

Silver King Majestic SK12MAJ Guida rapida

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manuale utente

DAN DRYER

DAN DRYER 282 Manuale utente

Essity

Essity Tork 473208 Manuale utente

CBS

CBS SD300BU-88 Guida all'installazione

Sealey

Sealey MK77 Manuale utente

Fluid Management

Fluid Management Accutinter 1600 Manuale utente

Graco

Graco Dispensit 1053-10C Guida alla risoluzione dei problemi

ITALTINTO

ITALTINTO i50 Manuale utente

Coca-Cola

Coca-Cola FREESTYLE 9000 Manuale utente

Graco

Graco ProMix 2KE Manuale di istruzioni

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manuale utente

Wayne

Wayne GLOBAL VISTA CNG Manuale utente

clarsen

clarsen H133 Manuale utente

PicoBrew

PicoBrew Zymatic Manuale utente

BOWMAN

BOWMAN BP-007 Manuale utente

HURAKAN

HURAKAN HKN-MT1 Manuale utente

Bobrick

Bobrick B-828 Manuale utente