Frigidaire FAK085R7V11 Manuale utente

installation instructions

For Slider Casement Air Conditioners

NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash,

or installation in a metal CASEMENT window. Modification may be necessary when installing in windows made

differently than those shown in these instructions.

A high window accessory kit is available for window heights up to 62" (1575mm). Part # EA103W.

TABLE OF CONTENTS

SUBJECT PAGE

Meeting Electrical Requirements 1

Electrical Connection 2

Preparing For Installation 2

Installing Unit in a Sliding Window 4

Alternate Window Jamb Applications 7

Installing Unit in a Casement Window 8

Meeting Electrical Requirements

OBSERVE ALL LOCAL GOVERNING CODES

AND ORDINANCES.

DO NOT, UNDER ANY CIRCUMSTANCES,

REMOVE THE POWER SUPPLY CORD

GROUNDING PRONG,

NOTE: If codes permit, and a separate

grounding wire is used; it is recommended that a

qualified electrician determine that the grounding

path is adequate and not interrupted by plastic,

non-metallic gaskets, or other insulating materials.

RECEPTACLE WIRING

Receptacle wiring should be a minimum of 14

gauge. Use copper wire only. It is your responsibility

to provide proper and adequate receptacle wiring,

installed by a qualified electrician.

ELECTRICAL REQUIREMENTS

A 115 volt (103.5 minimum, 126.5 maximum), 60

Hertz, AC only, 15 ampere fused electrical supply

is required. Atime delay fuse or time delay circuit

breaker is also required. A separate circuit, serving

only this appliance, MUST be provided.

P/N 66129901161

Electrical Connection

Electrical ground is required on this appliance.

Recommended grounding method:

For your personal safety, this appliance must be

grounded. This air conditioner includes a power

supply cord with a 3-prong grounding plug. To

minimize possible electrical shock hazard:

-cord must be plugged into a mating 3-prong

grounding-type wall receptacle,

-must be grounded in accordance with

National Electrical Code (ANSI1NFPA70-

latest version) and

-all local codes and ordinances.

If a mating 3-prong grounding-type wall receptacle is

not available, it is the responsibility of the consumer

to have a properly grounded 3-prong wall receptacle

installed by a qualified electrician.

3 Prong

Grounding Plug

3 Prong

Grounding Type

Wall Receptacle

Grounding

prong

Power Supply Cord

(6 feet long)

Preparing for Installation

Installation Tips

For wood-frame casement windows: It may be

necessary to construct a frame, using at least 1-inch

thick wood, with a 15-1t2-inch wide opening.

For brick or cement building construction: It may

be necessary to put a wood stool strip under AC, for

mounting purposes.

Tools Required

eFlat-head screwdriver

• Phillips-head screwdriver

• Carpenter's level

e Tape measure

• Fine tooth saw

o Electric or hand drill

• Knife and scissors

• Pencil

1. Makesureyou haveallthenecessaryparts.

Installation kit contents:

1. Platform(1)

2. Supportbrace(1)

3. Adjustmentbolt(1)

4. Hexflangenut- 1/4"(1)

5. Trackseal(1)

6. Sidechannelseal(1)

7. Foamsealstrip/Sashseal

8. Safetybracket(1)

9-11.Screw-#10x2-1/2"flat-head(2),OR

Screw- #10xl-314"pan-head(2),OR

Screw- #10xl"pan-head(2)

12. Screw- #8x314"panhead(6)

13. Screw- #8-32x314"self-threading(7)

14. Windowlockingbracket(1)

15. Plasticwindowpanel(1)

16. Sidechannel(2)

17. Screw- #8x318trusshead(6)

18. Panelframelsealassembly(1)

NOTE: Use scale below to measure length of your

screws. The scale will come in handy when

separating screws for installation.

(13rnm) (25rnm) (44mm) (63ram)

IDENTIFY SCREWS 112" 1" 13/4" 2 1/2"

BY LENGT

3/8" 3t4" 1 1/2" 2"

(10mm)(19mrn) (28mm) (50ram)

2. Choose a proper sized window, as shown right.

15-112 inches minimum width

16-114 inches maximum width (for

casement windows)

• 21-1/4 inches minimum height (with

window panel retainer)

20-5/16 inches minimum height

(window panel retainer removed)

= 39-7116 inches maximum height

NOTE: Height measurement must be of a clear

opening above mounting platform. In some cases,

due to a variety of stop and track arrangements, the

above dimensions may vary slightly. If necessary,

installation can be made by alternating window

jambs. (See Alternate Window JambApplications.)

(continued)

k 15 /2inches

-- minimum --

width

20 _/_ inches

minimum

height

39 _/_inches

maximum

Height

I.............

16 /4inches

maximum

width

(casement

windows)

3. Choose the proper window location.

Choose a window that allows the cooled air to flow

freely and directly into room(s) you wish to cool.

Remember, it is difficult to move air around corners.

Also, choose a window that is within 6 feet of an

electrical outlet. (See Meeting Electrical

RequirementstReceptacle wiring needs.) Do not

use an extension cord.

Installing Unit in a Sliding Window

1. Attach support brace to platform as shown.

Use adjustment bolt and hex flange nut to complete

assembly. Choose slot and adjustment bolt hole

locations that will create a 45 degree angle between

platform and support brace. Try assembly in the

window to determine if platform will rest properly, and

allow proper slope (3t16-inch lower on outside).

NOTE: If you are planning to use a siding-

protection board (see Step 5) on the outside of your

house, hold board in place when testing assembly in

window.

2. Measure, and lightly mark a line 8-11/16 inches

from window jamb.

NOTE: If any sash stop protrudes more than 1

inch from the side window jambs, the 8-11116-inch

measurement must be increased accordingly.

Screen and storm window frames may also require

adjustments to the measurement.

3. Center platform assembly on the line with inside

platform tab pressed against inside edge of window

track. Using the holes in the platform as a guide,

mark and drill two 9164-inch diameter holes. Drill

holes in either track or stool.

Property Damage Hazard-Failure to adhere to

the following precaution could result in

damage to window or air conditioner.

Be sure wood stool or window track is securely

attached to the building construction. Use longer

screws in sub-framing if necessary.

V2' (6mm) HEX FLANGE NUT

8 "/,_ !nches

Center platform

assembly on the

line with platform

tab pressed against

window track

Platform Assembly

A[te_nate screw Focation

(depending on the stool depth /

(continued 4

4. Peel off protective backing from track seal. Apply

seal to room side of window track. Center of seal strip

should coincide with the line marked in Step 2. The

two screw holes drilled in Step 3 should be directly

above seal strip in the inner track.

Apply track seal

to window side

5. Securely attach a siding-protection board to

side of house.

NOTE: Siding-protection board should be long

enough to span 2 wall studs.

Inside

wall of

house _ )rotection

6. Place platform assembly, with platform tab

against inside of window track, and attach it to

window jamb. Use appropriate length screws (Items

9-11 in Preparing For Installation).

7. Adjust platform assembly so that outside edge is

3116-inch lower than inside edge, as shown right.

This ensures proper water drainage from the air

conditioner.

8. Level platform assembly from side-to-side.

Also, make sure window track is level. Use leveling

shims as necessary to ensure unit is level from side-

to-side.

Put platforn

tab against

inside of

track

9. Measure height of window opening from top of

platform assembly as shown right. Subtract 20-5/8

inches. Mark this measurement on plastic window

panel, along the longer side. (continued)

10.Clampplastic window panel betweena board

andaworktable,andcutalongcuttinglinewithafine

toothsaw.Removeanyburrswithafile.

11.Fastenside channelstothesidesoftheAC

using3screws(Item17)perchannel.Startwithfirst

screwattopofchannel.Makesurehookendsof

channelsfacetowardbackof unit.

12,Slide plastic window panel into panel frame,

with the smooth side to the room. Slide panel frame

assembly into side channels of the AC cabinet. Make

sure plastic window panel is firmly enclosed on all

sides by the retainer grooves.

13. Cut side channel seal into 2 equal lengths.

Remove protective backing and apply it to the rear

side of cabinet side channels, starting just below

panel frame assembly. Pinch off excess length so

seal is even with the bottom of the cabinet side

channel.

Fastening Side Channels

14, To remove front

1. Remove the two front retaining screws from the

front frame.

2. Press firmly on each side of the metal case close

to the front, approximately 2/3 of the way down.

3. While pressing on the sides of the metal case,

gently pull the front out and lift up to release it

from the case.

4. Then release the electrical coupler plug.

NOTE: DO NOT push or pull air direction louvers.

Apply weather

seal to side

channels just

below edge of

panel frame

Front

Retaining

Screw

15. Place AC in window opening. As shown right, it

should sit on platform assembly so that window panel

frame, and cabinet side channels are against top and

side window jambs. (continued)

Slide inner

window sash

firmly against

Cabinet.

16. Slide inner window sash firmly against side

of the cabinet. Make sure not to peel the seal strips

from the window track and cabinet side channels. If

the panel frame does not fit snugly to the inner

window sash, secure the panel frame to the sash

with #8x3/4-inch screws, or #8-32x3/4-inch self-

threading screws. Use the partially plugged holes in

the panel frame. Drill 1/8-inch pilot holes for the

screws.

17. Hook the safety bracket over the base of the

unit and fasten it to the front of the platform

assembly. Use a #8-32x3t4-inch self-threading

screw.

NOTE,: The bracket prevents movement of the

air conditioner (either in or out) after completing the

installation.

18. Stuff the foam seal strip/sash seal between

the vertical sash and the window glass, as shown

right.

19. Use the window locking bracket to lock the

inner window sash to the base of the outer window

sash. Use one #8x3t4-inch screw, or #8-32x3t4-

inch self-threading screw. (Drill ll8-inch pilot hole).

20. To replace the front

First reconnect the coupler plugs, make the exhaust

control positioned through the front in the proper

location. Gently push the front into position on the

cabinet. It should click into place. Then replace the

retaining screws that holds the panel in place.

Do not push or pull the front panel louvers.

Sash seaL.

Window

locking

Slide inner

window sash

firmly against

Cabinet

Install safety bracket

cket

Alternate Window Jamb

Applications

To install in windows having no flanges or wood stops

on the top and side jambs, the channels and panel

frame must fit against a mating flange (or 1116-inch

max. thick angle) attached to the window jambs.

Figure Ashows this angle installed. Figures B & C

show alternate treatments. On the sash side of the

opening, the leading corner of the inner sash

becomes the flange. You can purchase the angle

strip locally.

A B C

Add al_Jle to Add wood Add t6-or t 8-

wood stop as shown gauge angle

Installing the Unit in a Casement

Window

NOTE: Open the window the maximum amount to

allow for clearance of the cabinet. The crank handle

should be removed to allow the platform to be

fastened to the jamb. If the window cannot open far

enough (more than 15-112 inches) for the cabinet to

clear the window, remove the window entirely by

drilling out the rivets. Bolts can serve as the pivots in

the future.

To avoid crank handle and window clearance

problems, the unit can be installed in a stationary

sash section. However, the horizontal mullion and the

2 glass panels must be removed before installation.

1. Attach support brace to platform as shown. Use

the adjustment bolt and hex flange nut to complete

the assembly. Choose the slot and adjustment bolt

hole locations that will create a 45 degree angle

between the platform and the support brace. Try the

assembly in the window to determine if the platform

will rest properly, and allow the proper slope (3116-

inch lower on outside).

NOTE: If you are planning to use a siding-

protection board (see Step 6) on the outside of your

house, hold the board in place when testing the

assembly in the window.

2. Drill a 9/64-inch diameter pilot hole in the

window jamb an equal distance from each side of the

jamb, and 3116-inch up from the window sill. If the

hole coincides with the window lever slot in the jamb

bottom, an additional hole will have to be drilled

through the platform edge and the window jamb to

miss this slot.

3. Peel off the protective backing from the track

seal, and stick the seal to the window sill on the

outside of the bottom jamb.

V_"(6ram) HEX FLANGE NUT

Equal distance from both sides

8 'V, inches }1

Apply track s_al [o [he outside

edge of the bo[tom window jamb

Platform Assembiy

4. Screw the platform assembly to the window

jamb through the pilot hole you drilled in Step 2. Use

a #8x314-inch self-threading screw. (continued)

Track sea_

5. Adjust the platform assembly so that the rear of

the air conditioner will be 3/16-inch lower than the

front. This ensures proper water drainage from the

air conditioner.

NOTE: A projection below the base of the air

conditioner will require the rear of the platform to be

7116-inch lower than the front to create the 3/16-inch

slant from front to rear.

6. Securely attach a siding-protection board to the

side of the house where the platform assembly hit the

house. The siding-protection board should be long

enough to span 2 wall studs.

Fasten siding-

protection board to

the house siding.

Rear is at ]east

7/16" lower

than front

7. Measure the height of the window opening

from the top of the platform assembly. Subtract

20-5/8 inches. Mark this measurement on the plastic

window panel, along the longer side.

8. Clamp the plastic window panel between a

board and a work table, and cut along the cutting line

with a fine tooth saw. Remove any burrs with a file.

9. Fasten the side channels to the sides of the

unit using three screws (Item 17) per channel. Make

sure hook ends of channels face toward the back of

unit.

10. Slide the plastic window panel into the panel

frame with the smooth side to the outside. Slide the

panel frame assembly into the side channels of the

air conditioner cabinet. Make sure the plastic window

panel is firmly enclosed on all sides by the retainer

grooves. (continued)

jPanet frame

Piastic window panel

11. Cut side channel seal into 2 equal lengths.

Remove the protective backing and apply it to the

rear side of the cabinet side channels, starting just

below the panel frame assembly. Pinch off excess

length so the seal is even with the bottom of the

cabinet side channel.

Apply weather

seal _ side

channelsjust

below edge of

panelfame

12. To remove front

1. Remove the two front retaining screws from the

front frame.

2. Press firmly on each side of the metal case close

to the front, approximately 2t3 of the way down.

3. While pressing on the sides of the metal case,

gently pull the front out and lift up to release it

from the case.

4. Then release the electrical coupler plug.

NOTE: DO NOT push or pull air direction louvers.

Front

Retaining

Screw

,¢

13. Place the air conditioner in the window

opening as shown to the right. It should sit on the

platform assembly so that the window panel frame,

and the cabinet side channels are against the top and

side window jambs. Side channels should overlap

side window jambs equally.

14. Drill two 9/64-inch diameter pilot holes in the

top window jamb in line with the partially plugged

holes in the panel frame. Secure the panel fame to

the window jamb with two #8-32x3t4-inch self-

threading screws. If additional holding is necessary,

two screws may be used on the sides of the panel

frame as well.

15. Drill two screw-clearance holes in the cabinet

side channels (near bottom) and two 9t64-inch

diameter pilot holes in the side window jambs. Secure

the cabinet side channels to the window jambs with

two #8-32x3t4-inch self-threading screws. When

doing this, be careful not to twist the side channel

seals with the screws.

NOTE: Inserting screws will prevent the air

conditioner from being pushed into the room.

16. To replace the front

First reconnect the coupler plugs, make the

exhaust control positioned through the front

in the proper location. Gently push the front

into position on the cabinet. It should click into

place. Then replace the retaining screws that

holds the panel in place.

Do not push or pull the front panel louvers.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Frigidaire Condizionatore d'aria

Frigidaire

Frigidaire FFRE0533S1E0 Manuale utente

Frigidaire

Frigidaire FRS09PYS1 Manuale utente

Frigidaire

Frigidaire FHTE083WA1 Manuale del proprietario

Frigidaire

Frigidaire CRA084KT711 Manuale del proprietario

Frigidaire

Frigidaire FAX052P7AD Manuale utente

Frigidaire

Frigidaire FRS123LS1 Manuale del proprietario

Frigidaire

Frigidaire FAA067P7 Manuale utente

Frigidaire

Frigidaire FAC052N7A1 Manuale utente

Frigidaire

Frigidaire FAC065L7A1 Manuale utente

Frigidaire

Frigidaire FRP12ETT2A Manuale utente

Frigidaire

Frigidaire FAA063P7A16 Manuale utente

Frigidaire

Frigidaire Room Air Conditioner Manuale utente

Frigidaire

Frigidaire FAS255J2A2 Manuale utente

Frigidaire

Frigidaire FAC055J7A1 Manuale utente

Frigidaire

Frigidaire FAC085M7A1 Manuale utente

Frigidaire

Frigidaire FFPH1422R1 Manuale del proprietario

Frigidaire

Frigidaire FAA055P7 Manuale utente

Frigidaire

Frigidaire FAX050S7AF Manuale utente

Frigidaire

Frigidaire FAX052P7 Manuale utente

Frigidaire

Frigidaire 220201d036 Manuale utente

Frigidaire

Frigidaire FRA123KT1 Manuale utente

Frigidaire

Frigidaire FRA054XT7 Manuale utente

Frigidaire

Frigidaire FAA055P7A 5,200 Manuale utente

Frigidaire

Frigidaire FFRA051WAE Manuale utente

Manuali Condizionatore d'aria popolari di altre marche

Spheros

Spheros CC 355 Manuale utente

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuale utente

Panasonic

Panasonic CS-E12HKEW Manuale utente

nedis

nedis ACMB1WT7 Manuale utente

Samsung

Samsung AR KV Series Guida

Daikin

Daikin FCFV50A Manuale utente

Fujitsu

Fujitsu Inverter ASBA30JFC Manuale utente

Toshiba

Toshiba RAS-M10SMUV-E Manuale utente

Daikin

Daikin FXLQ20MAVE Manuale utente

Hitachi

Hitachi RAS-E24CAK Manuale utente

CIAT

CIAT Magister 2 Series Guida

Bestron

Bestron AAC6000 Manuale utente

Hisense

Hisense 7K Manuale tecnico

Samsung

Samsung AS09HM3N Manuale utente

Soleus Air

Soleus Air GB-PAC-08E4 Manuale utente

McQuay

McQuay MCK020A Manuale utente

Webasto

Webasto Frigo Top 25 DS Manuale utente

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Manuale utente