FS SG-5110 Manuale utente
MULTISERVICE SECURITY
GATEWAY
SG-5110
Quick Start Guide V1.0
USB
SATA
0/MGMT
1 2 3 4 5 6 7
PWR
RESET
CONSOLE
SYS
8F 9F
SPEED
10/100
1000
LINK/ACT
Security Gateway
DOWN
LINK
SFP+ SFP
Accessories
Introduction
Thank you for choosing SG-5110 security gateway. This guide is designed to familiarize you with the
layout of the gateway and describes how to deploy the gateway in your network.
M4 Screw x6
Rubber Pad x4
Power Cord x1
Mounting Bracket x2
Console Cable x1
Power Cord Tie x1
Network Cable x1
SG-5110
SATA
0/MGMT 1 2 3 4 5 6 7
PWR RESET
CONSOLE
USB
SYS
8F 9F
SPEED
10/100
1000
LINK/ACT
Security Gateway
DOWN
LINK
SFP+ SFP
NOTE: This gateway has dust plugs delivered with it. Keep the dust plugs properly and use
them to protect idle optical ports.
Front Panel Ports
Front Panel Button
Hardware Overview
Back Panel
RJ45 10/100/1000BASE-T ports for Ethernet connection
SFP port for 1G connection
SFP
SFP+
CONSOLE
MGMT
USB
An RJ45 console port for serial management
An Ethernet management port
A USB management port for software and configuration backup
and offline software upgrade
SFP+ port for 10G connection
Ports Description
Power Supply ON/OFF
Hard Disk Drive Slot
SATA
0/MGMT 1 2 3 4 5 6 7
PWR RESET
CONSOLE
USB
SYS
8F 9F
SPEED
10/100
1000
LINK/ACT
Security Gateway
DOWN
LINK
SFP+ SFP
SATA
0/MGMT 1 2 3 4 5 6 7
PWR RESET
CONSOLE
USB
SYS
8F 9F
SPEED
10/100
1000
LINK/ACT
Security Gateway
DOWN
LINK
SFP+ SFP
RJ45
CONSOLE
MGMT
USB SFP+ SFP
RESET
RESET
Press and release the RESET button to restart the device. To restore
to factory default, press and hold the RESET button for more than
three seconds.
Button Description
100-240V~; 50/60HZ,0.6A OFF
ON
SATA
Grounding Point
Back Panel Button
Power ON/OFF Control the gateway power supply.
Button Description
Front Panel LEDs
PWR
SYS
SATA
LINK/ACT
SPEED
SFP+
SFP
Off
Solid Green
Blinking Green
Solid Green
Solid Green
Blinking Green
Solid Green
Blinking Green
Off
Solid Orange
Solid Green
Solid Green
Blinking Green
Blinking Green
LEDs Status
The power module is not in the position or fails.
The power module is working properly.
The system is being initialized.
The initialization process is complete.
Solid Red The system sends out an alarm.
The SATA disk is installed.
The port is receiving or transmitting data.
The port is connected at 10/100/1000M.
The port is connected.
The port is receiving or transmitting data.
The port is connected.
The port is receiving or transmitting data.
The port is connected at 1000M.
The port is connected at 10/100M.
The SATA disk is reading or writing data.
Description
SATA
0/MGMT 1 2 3 4 5 6 7
PWR RESET
CONSOLE
USB
SYS
8F 9F
SPEED
10/100
1000
LINK/ACT
Security Gateway
DOWN
LINK
SFP+ SFP
SYS
SATA
PWR SFP+ SFP
LINK/ACT
SPEED
Installation Requirements
Before you begin the installation, make sure that you have the following:
Phillips screwdriver.
Do not place the device in a damp or wet location. Do not let any liquid enter the chassis.
Do not install the equipment in a dusty environment.
Keep the device away from heat sources.
Ensure the normal grounding of device.
Wear an anti-static wrist strap to install and maintain the device.
Use UPS (Uninterruptible Power Supply) to prevent power failure and other interferences.
Mounting the Gateway
Desk Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
USB
SATA
0/MGMT
1 2 3 4 5 6 7
PWR
RESET
CONSOLE
SYS
8F 9F
SPEED
10/100
1000
LINK/ACT
Security Gateway
DOWN
LINK
SFP+ SFP
SATA
0/MGMT
1 2 3 4
PWR
RESET
CONSOLE
USB
SYS
SATA
0/MGMT
1 2 3 4
PWR
RESET
CONSOLE
USB
SYS
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ-45 Ethernet cables and fiber optical cables for connecting network
devices.
Site Environment：
Rack Mounting
1. Secure the mounting brackets to the two sides of the gateway with six M4 screws.
2. Attach the gateway to the rack using four M6 screws and cage nuts.
5 6 7 8F 9F
SPEED
10/100
1000
LINK/ACT
Security Gateway
DOWN
LINK
SFP+ SFP
4 5 6 7 8F 9F
SPEED
10/100
1000
LINK/ACT
Security Gateway
DOWN
LINK
SFP+ SFP
Grounding the Gateway
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
gateway is mounted.
2. Secure the grounding lug to the grounding point on the gateway back panel with the washers and
screws.
Connecting the Power
1. Plug the AC power cord into the power port on the back of the gateway.
2. Connect the other end of the power cord to an AC power source.
CAUTION: Do not install the power cord while the power is on, and when the power cord
is connected, the fan will start to operate whether the power button is on or off.
100-240V~; 50/60HZ,0.6A
OFF
ON
SATA
Connecting the SFP/SFP+ Ports
1. Plug the compatible SFP/SFP+ transceiver into the fiber port.
2. Connect a fiber optic cable to the fiber transceiver. Then connect the other end of the cable to
another fiber device.
CAUTION: Laser beams will cause eye damage. Do not look into bores of optical
modules or optical fibers without eye protection.
Connecting the RJ45 Ports
1. Connect an Ethernet cable to the RJ45 port of a computer or other network devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the gateway.
OFF
ON
PSO
~100-240V/1A
OFF
ON
PSO
~100-240V/1A
SATA
0/MGMT
1 2 3 4 5 6 7
PWR
RESET
CONSOLE
USB
SYS
8F 9F
SFP+ SFP
0/MGMT
RESET
CONSOLE
USB
PWR
SYS
SPEED
10/100
1000
Security Gateway
LINK/ACT
DOWN
LINK
9F8F7654321
SFPSFP+
Connecting the Console Port
1. Insert the RJ45 connector into the RJ45 console port on the front of the gateway.
2. Connect the DB9 female connector of the console cable to RS-232 serial port on the computer.
SATA
0/MGMT
1 2 3 4 5 6 7
PWR
RESET
CONSOLE
USB
SYS
8F 9F
SPEED
10/100
1000
SFP+ SFP
0/MGMT
RESET
CONSOLE
USB
8764321
SATA
PWR
SYS
1. Connect one end of a standard RJ45 Ethernet cable to a computer.
2. Connect the other end of the cable to the MGMT port on the front of the gateway.
Connecting the MGMT Port
Configuring the Gateway
Configuring the Gateway Using the Web-based Interface
Step 1: Connect the computer to the Management port of the gateway using the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x. (“x” is any number from 2 to 254.)
?x
OK Cancel
General
IP address:
Subnet mask:
Default g a t e w a y :
You can get IP settings assigned automatically if your net w o r k
supports this capabil i t y . O t herwise, y o u need t o a sk your net w o r k
adminis t r a t o r f o r the appropr i a t e IP settings .
Inter net P roto c ol Versi o n 4 ( TCP/I P v4) Properties
Use the following IP address:
Obtain an IP address a utomatically
Preferred DNS server:
Alternate DNS server:
Validate settings upon exit A d v anc e d ...
. . .21168192
0255
255255
. . .
. . .
. . .
. . .
Obtain DNSser v e r a ddre s s automatically
Us e the following DNS s e r ve r addresses:
Step 3: Open a browser, type http://192.168.1.1, and enter the default username and password,
admin/admin.
Step 4: Click Log In to display the web-based configuration page. You are then required to enter and
configure a new password for the account the first time you log in.
LINK/ACT
Security Gateway
DOWN
LINK
SPEED
10/100
1000
Wireless Controller
LINK/ACT
DOWN
LINK
8F7F8
SFPSFP
Internet Explorer 10/11, Google Chrome, Firefox
Recommended
Log In
admin
*****
Altri manuali per SG-5110
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali FS Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
