FSR CP-100 Manuale utente

LIT1269

CP-100 / 200 Compass Plus Switcher

Quick Guide for using Serial and Ethernet Control

Rev.1.03 January 16, 2009

244 Bergen Blvd Woodland Park NJ 07424 973-785-4347 www.fsrinc.com

2

General Notes:

•There are two scalers in the CP. Because of this, we can achieve

seamless switching without freezing the frame or fading to black.

It also adds a little time before an input will be ready to be

switched to the mains.

•All requests are terminated with a carriage return.

•

<CR>

stands for carriage return, which is a 0C in hex, or 13 in

decimal.

•“CP” refers to an FSR CP-100 or CP-200 Compass Plus Switcher

Power Up Handling

It is required to wait for 50 seconds after power up before attempting to log on,

especially if using the Ethernet connection. If the user attempts to log in before

the CP’s main program is loaded and running, you may log in but never be able

to get to the CP main program.

Logging In

The CP will prompt for a user id and password. The id is “user” MUST BE

LOWER CASE!!! The password is just a carriage return. The user remains logged

on until the CP is powered down or the user closes the connection.

Switching Inputs

There are two ways of switching inputs to Main serially; one requires two

messages. The other requires only one.

Two Message Method:

Send an ISEL message with the input number, then send a TAKE message

after waiting for the prompt (“>”). Input numbers range from 1 –9, inputs

1-8, 9=SDI. To switch input 3 to the Main, the user send the following:

ISEL –i3<

CR>

Waitforprompt

TAKE<

CR

>

It important to note that the ‘i’ in the ISEL message must be lower case.

It will not work otherwise.

3

One Message Method:

Set up the auto-take function after logging on. To do that, simply send

out the following message:

AUTOTAKE –m1<

CR>

The ‘m’ in the AUTOTAKE request MUST be lowercase, ‘1’ turns on

AUTOTAKE, ‘0’ turns off AUTOTAKE.

When the user wants to switch inputs he/she only needs to send a ISEL request.

For example: To switch to the SDI source the user sends the following message:

ISEL –i9<

CR

>

NOTE: Since the CP has two scalers it is important to remember that it will take

a little time to lock on the signal before the input is switched.

Switching to LOGO

The image to be saved as a logo should be currently active on the main display

from one of the 6 analog or 2 SDI inputs. Logos should be saved from the CP

front panel. This is accomplished by pressing and holding the “SEL” button until

the setup menu appears on the LCD screen. The user will then scroll down to

the “LOGO” setup and press the “SEL” button. Setup the LOGO number to save

the image to and then scroll to save the logo. The default logo number is

“LOGO1”.

To switch the LOGO2 to the main screen the user sends the following message:

LOGOSEL –l2

The ‘l’ MUST BE lower case, and the logo number is 1 – 3.

NOTE: If LOGO is set on the Main, or Next, you CANNOT get into the LOGO

setup menu until you switch LOGO of the Main and Next.

Questo manuale è adatto per i seguenti modelli

1

Indice

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente