Fujitsu M3091DC Manuale utente
2-
M3091DC Image Scanner
OPERATION GUIDE
C150-E140-03EN
M3091DC Image Scanner Operation Guide
FOR SAFE OPERATION
Treatment of This Manual
Since this manual contains important information for using the M3091DC, read it
thoroughly before using the product. Use the M3091DC only after thoroughly reading and
understanding especially the section "Important Alert Messages" in this manual. Keep this
manual handy, and store it carefully.
Notice to
AmericanUsers Federal Communications Commission
Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Adjust or relocate the receiving antenna.
•Increase the distance between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from the
circuit the receiver is connected to.
•Consult your dealer or an experienced radio/TV technician for help.
FCC warning: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
the equipment.
M3091DC Image Scanner Operation Guide
Notice to
AmericanUsers Notes
•The use of a non-shielded interface cable with the referenced device is
prohibited. The length of the parallelinterface cable must be 3 meters
(10 feet) or less. The length of the serial interface cable must be 15
meters (50 feet) or less.
•The length of the power cord must be 3 meters (10 feet) or less.
Notice to
Canadian Users This digital apparatus does not exceed the class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numériqué n'émet pas de bruits radioélectnques
dépassant les limites applicables aux appareils numériques de la classe B
prescrites dans le Règlementsur le brouillage radioélectrique édicté par le
ministère des Comunications du Canada.
Notice to
German Users Bescheinigung des Herstellers/Importeurs
Hiermit wird bescheinigt, daß der/dieldas
•M3091DC in Übereinsstimmung mit den Bestimmungen der
•AmtsblVfg 243/1991 funkentstört ist. Der Deutschen Bundespost wurde
das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung
zur Überprüfung der Serie auf Einhaltung der Bestimmungen
eingeräumt.
•Maschinenlärminformationsverordnung 3. GS GV, 18.01.1991:
Der höchste Schalldruckpegel beträgt 70 dB (A) order weniger
gemäß ISO/7779.
M3091DC Image Scanner Operation Guide
Warning: This equipment may cause electromagnetic interference. It has not been tested
to show compliance with AS3548 Class A equipment, which is designed to provide
reasonable protection against such interference.
Operation of this equipment in a residential area is likely to cause interference in which case
the user at his own expense will be required to take whatever measures may be required to
correct the interference.
As an ENERGYSTAR ®Partner, Fujitsu Limited has determined that
this scanner meets ENERGYSTAR ®guidelines for energy efficiency.
ENERGYSTAR ®is a U. S. registered mark.
Trademark Acknowledgment
Fujitsu is a registered trademark of Fujitsu Limited.
ThirdEdition April 2000
The contents of this manual may be revised without prior notice.
The contents of this manual shall not be disclosed in any way or reproduced in any media
without the express written permission of Fujitsu Limited.
All Rights Reserved, Copyright FUJITSU LIMITED 1999
M3091DC Image Scanner Operation Guide i
Preface
Thank you very much for your purchase of the M3091DC Image Scanner.
The M3091DC Image Scanner can read very fine color images.
As this manual explains the basic handling of the scanner, read it carefully
to use the scanner properly.
In this manual, the MicrosoftWindows NTOperating System is
referred to as Windows NT, the MicrosoftWindows 95Operating
System is referred to as Windows 95, and the MicrosoftWindows 98
Operating System is referred to as Windows 98.
Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation of the U.S. in the United States and other countries.
Other company names or product names appearing in this manual are
trademarks or registered trademarks of individual companies.
ii M3091DC Image Scanner Operation Guide
Important Notes to Users
Every user is requested to use this product including the manuals and
software supplied with the product at the user's own responsibility.
Fujitsu assumes no liability with respect to any damage or loss caused to
data as the result of using this product.
Please understand that the warranty range for failure of this product will
never exceed the amount of money paid by the user for the product.
Fujitsu prohibits any user from using software supplied with this product
or any other update software for this product for any purpose other than
incorporation into this product. Fujitsu also prohibits any user from
reworking or disassembling such software.
M3091DC Image Scanner Operation Guide iii
Conventions for Alert Messages
This manual uses alert messages to prevent users and bystanders from
being injured or from suffering damage to their property. An alert
message consists of an alert signal and alert statements. The alert signals
and their meanings are as follows.
This indicates a hazardous situation that could
result in serious personal injury if the user
does not perform the procedure correctly.
This indicates a hazardous situation that could
result in minor or moderate personal injury if
the user does not perform the procedure
correctly. This alert signal also indicates that
damage to the products or other property may
occur if the user does not perform the
procedure correctly.
In addition to the above-cited signals, the
following symbols are also used to provide
detailed information concerning injury or
damage:
Electric shock
High
temperature
The symbol marked with
indicates a warning or caution.
The concrete meaning of an alert
is illustrated in the symbol. (The
example at left indicates caution
against an electric shockand
caution against an high
temperature.)
iv M3091DC Image Scanner Operation Guide
Disassembly
The symbol marked with
indicates what must not be done
(prohibited action). The concrete
meaning of the action is
illustrated in the symbol. (The
example at left indicates the
prohibition of disassembly.)
Plug
The symbol marked with
indicates what must be observed.
The concrete meaning of the
action is illustrated in the symbol.
(The example at left directs the
operator to disconnect the power
plug from the outlet.)
M3091DC Image Scanner Operation Guide v
Important Alert Items
Important Alert Messages
Important alert messages applicable to the M3091DC Image Scanner are
listed below. Observe these directions for safe operation of the scanner.
Alert concerning power supply
Prohibited
−Do not insert the AC adapter to any outlet other than one dedicated to
15 A at 100 VAC. Do not make a starburst connection.
It could result in a fire or electric shock.
−Do not damage, break, or process the power cord. Do not put a heavy
item on, pull, or forcibly bend it.
It could result in a fire or electric shock.
−Use only the power cord (AC adapter) supplied with the scanner. Do
not use an extension cord.
It could result in abnormal heat or a fire.
−Do not use the power cord or AC adapter if it is damaged or loose in
connection with the outlet.
It could result in a fire or electric shock. Ask your sales agency or
Fujitsu Limited for repair.
vi M3091DC Image Scanner Operation Guide
Electric
shock
−Disconnect the AC adapter from the outlet before connecting an
interface cable or optional product.
Failure to do so could result in an electric shock.
−Do not handle the AC adapter with wet handswhen connecting or
disconnecting it.
It could result in an electric shock.
Direction
−If the AC adapter or outlet is covered with dust, clean it well with a
dry cloth.
Failure to do so could result in a fire.
Plug
−If one of the following occurs, promptly stop using the scanner and
disconnect the AC adapter from the outlet, then call your sales agency
or Fujitsu Limited:
−The scanner generates smoke or the outside of the scanner is
extraordinarily hot.
−The scanner generates an abnormal sound.
−Water enters the inside of the scanner.
Failure to do so could result in a fire.
−In case of thunder, disconnect the AC adapter from the outlet.
Failure to do so could result in damage to the scanner or other
property of the customer.
Altri manuali per M3091DC
1
Indice
Altri manuali Fujitsu Scanner
Fujitsu
Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf Manuale utente
Fujitsu
Fujitsu FI-4860C2 Guida alla configurazione
Fujitsu
Fujitsu fi-5650C Guida alla configurazione
Fujitsu
Fujitsu fi-5650C Guida alla configurazione
Fujitsu
Fujitsu M3096EX Guida alla configurazione
Fujitsu
Fujitsu FI-5900C Manuale utente
Fujitsu
Fujitsu FI-6130 Manuale utente
Fujitsu
Fujitsu ScanSnap N1800 Manuale utente
Fujitsu
Fujitsu M4099D Guida alla configurazione
Fujitsu
Fujitsu SNAPSNAP IX500 Manuale utente
Fujitsu
Fujitsu M3099EH Manuale utente
Fujitsu
Fujitsu ScanSnap iX100 Istruzioni per il montaggio
Fujitsu
Fujitsu CardMinder Series Manuale utente
Fujitsu
Fujitsu FI-6000NS Manuale
Fujitsu
Fujitsu C150-E049-02EN Manuale di installazione e funzionamento
Fujitsu
Fujitsu fi-565PR Manuale
Fujitsu
Fujitsu Libra S6 Manuale utente
Fujitsu
Fujitsu FI-6000NS Manuale utente
Fujitsu
Fujitsu fi-7800 Manuale utente
Fujitsu
Fujitsu fi-4860C Manuale
