GAI-Tronics XCP0030A Manuale utente
Pub. 43003-014B
GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA
610-777-1374 n800-492-1212 nFax: 610-775-6540
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
Model XCP0030A Telco Interface Kit
Field Installation Kit Instructions
Confidentiality Notice
This manual is provided solely as an operational, installation, and maintenance guide and contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics.
GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,
and such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any
third party.
General Information
The Telco Interface Kit adapts the three DB25 rear panel connectors to a single 50-pin standard
connector. The unit mounts on the rear panel of the ICP9000 Series Desktop Console, ICP9000
Navigator Series MCU, or the Supervisor option installed on the respective unit, and plugs into the three
DB25 connectors, P40 (a) (b) (c).
The Model XCP0030A 25-Pair Telco Interface Kit includes the following components:
Qty Description
1Telco Interface Adapter
2#6-32 ×1.625-inch Phillips screws
Installation
ICP9000 Series Desktop Console
1. Disconnect the power from the ICP9000 Series Desktop Console and remove all attached land-line
and accessory cables from the rear of the unit.
2. Mount the Telco Interface to the rear panel of the console or the Supervisor panel. Refer to Figure 1
or Figure 2. Position the Telco Interface so that the three DB25 connector plugs line up with the
DB25 connector receptacles on the rear panel.
3. Secure the Telco Interface with the supplied #6-32 screws shown in Figure 1 or Figure 2, tightening
them until the Telco unit is snug against the rear panel or the Supervisor panel.
Pub. 43003-014B
Model XCP0030A Telco Interface Kit Page: 2of 4
11/02
Figure 1.
Figure 2.
Pub. 43003-014B
Model XCP0030A Telco Interface Kit Page: 3of 4
11/02
4. Plug one end of a standard DB50 connector plug into the single 50-pin Telco connector and terminate
the other end to an applicable punch block. Place the connector plug bracket over the 50-pin
connector and secure with two screws. The bracket secures the connector to the Telco interface.
5. Reattach the necessary accessory cables and reconnect the power.
Note: The Supervisor unit input connectors and output connectors can each have a separate Telco
Interface unit attached.
ICP9000 Navigator Series MCU
1. Disconnect the power from the ICP9000 Navigator Series MCU and remove all attached land-line
and accessory cables from the rear of the unit.
2. Mount the Telco Interface to the rear panel of the console or the Supervisor panel. Refer to Figure 3
or Figure 4. Position the Telco Interface so that the three DB25 connector plugs line up with the
DB25 connector receptacles on the rear panel.
3. Secure the Telco Interface with the supplied #6-32 screws shown in Figure 3 or Figure 4, tightening
them until the Telco unit is snug against the rear panel or the Supervisor panel.
4. Plug one end of a standard DB50 connector plug into the single 50-pin Telco connector and terminate
the other end to an applicable punch block. Place the connector plug bracket over the 50-pin
connector and secure with two screws. The bracket secures the connector to the Telco interface.
5. Reattach the necessary accessory cables and reconnect the power.
Note: The Supervisor unit input connectors and output connectors can each have a separate Telco
Interface unit attached.
Figure 3.
Pub. 43003-014B
Model XCP0030A Telco Interface Kit Page: 4of 4
11/02
Telco Interface Pin Connectors
Pair # (Pin #) Pin Function (Pin #)
(for dc pos, neg) Pair # (Pin #) Pin Function (Pin #)
(for dc pos, neg)
1 (1, 26) TX 1 (14, 15) 13 (13, 38) TX 7 (8, 9)
2 (2, 27) RX 1 (1, 2) 14 (14, 39) RX 7 (10, 11)
3 (3, 28) TX 2 (3, 4) 15 (15, 40) TX 8 (12, 13)
4 (4, 29) RX 2 (5, 6) 16 (16, 41) RX 8 (24, 25)
5 (5, 30) TX 3 (8, 9) 17 (17, 42) TX 9 (14, 15)
6 (6, 31) RX 3 (10, 11) 18 (18, 43) RX 9 (1, 2)
7 (7, 32) TX 4 (12, 13) 19 (19, 44) TX 10 (3, 4)
8 (8, 33) RX 4 (24, 25) 20 (20, 45) RX 10 (5, 6)
9 (9, 34) TX 5 (14, 15) 21 (21, 46) TX 11 (8, 9)
10 (10, 35) RX 5 (1, 2) 22 (22, 47) RX 11 (10, 11)
11 (11, 36) TX 6 (3, 4) 23 (23, 48) TX 12 (12, 13)
12 (12, 37) RX 6 (5, 6) 24 (24, 49) RX 12 (24, 25)
Figure 4.
Indice
Altri manuali GAI-Tronics Ricevitore
