GAMA Electronics RF24V1C Manuale utente
RF24V1C
Instruction Manual
WWW.GAMAINC.COM
Included in this Kit:
(1) RF24V1C Receiver
(1) 2-Button Transmitter *Image shown with standard transmitter*
- 2-Button Rechargeable Transmitter GKF-WPTX-2
Available accessories:
- Package of A23 12V Alkaline Batteries A23-6
- 2-Button Waterproof Transmitter KF340-2WP
The RF24V1C is an RF receiver operating at a fixed frequency of 340 MHz. The receiver operates from 24VDC and
provides one isolated form C relay contact (normally open and normally closed contacts with one common). Up to
twelve, two button keyfob transmitters can be used to activate the receiver's relay. The relay can be configured to
function as a latching relay or momentary relay. Each transmitter has a unique address that is transmitted when a
button is pressed. A "program" button is provided on the receiver to program the transmitter(s) address into the
receiver's memory. The relay mode (latching or momentary) is programmed into the receiver's memory during the
programming process. An LED on the receiver indicates the receiver's programming status and illuminates when the
relay is energized. The receiver is encased in a small, waterproof enclosure. The typical operating range between
receiver and transmitter is up to 100 feet.
"Latching" vs. "momentary" relay operating modes: When the receiver is configured for "latching" mode, the relay will
energize when the "UP" button is pressed on the keyfob. The relay will remain energized until the "DOWN" button on
the keyfob is pressed. If multiple keyfobs are used any keyfob can energize the relay and any keyfob can de-energize
the relay. When the receiver is configured for "momentary" mode the relay will energize and remain energized as
long as the "UP" button is pressed on the keyfob. The "DOWN" button on the keyfob transmitter has no effect in this
mode
Maximum ratings:
Power for the receiver can be in the range of 21 to 24Vdc. The receiver is reverse polarity protected.
The relay contacts are electrically isolated from the DC power leads.
The relay contacts are rated at 10 Amps @ 30Vdc or 120/240Vac.
Power consumption:
10mA when the relay is de-energized. 45mA when the relay is energized
Dimensions:
1.65" X 1.46" X 1.04". The flexible whip antenna extends 3" from the enclosure.
Net weight 2.35 oz. . Page 1 REV A 07/07/20
- 340MHz Long Range Antenna LRA-340 *See Page 3 for Setup*
- 2-Button Keyfob Transmitter KF340-2
- Clear Protective Transmitter Pouch ZLB-67
Programming Instructions
Each transmitter has its own unique internal address along with the data as to which button is pressed and transmitted.
The receiver needs to be programmed to respond only to the specific transmitter it is intended to operate with. The
following steps configure the receiver to operate with a particular transmitter. Up to 30 transmitters can be programmed
to one receiver. Please read the entire programming procedure before starting. When the receiver enters program
mode, all previous transmitter addresses that were programmed will be erased from the receiver's memory.
1. Locate the pushbutton labeled "PROGRAM" on the receiver. Press and hold this button until the red LED next to the
program button illuminates (approximately 3 seconds). The receiver is now in the transmitter program mode. Release
the button. At this point all previously programmed transmitter addresses are erased from the receiver's memory.
2. To configure the receiver for a latching output, go to Step 4.
3. To configure the receiver for momentary output, press and release the UP button on the transmitter and verify that the
red program LED
extinguishes and then illuminates (blinks once). Proceed to Step 5.
4. To configure the receiver for latching output, press and release the DOWN button on the transmitter and verify that
the red program LED extinguishes and illuminates (blinks once).
5. Repeat previous step for additional transmitters that will operate with this particular receiver. The red LED on the
receiver will extinguish and illuminate (blink) once for the first transmitter being programmed, twice for the second, three
times for the third, etc. The receiver will not respond to transmitters that have already been programmed. The first
transmitter that is programmed determines the receiver’s relay operating mode.
6. The receiver will return to normal mode if no transmitter buttons are pressed for 5-seconds. The red LED on the
receiver will blink rapidly, then extinguish. The receiver is now in the normal mode of operation. This completes the
programming instructions. The receiver will retain all of its programming even when power is removed.
WWW.GAMAINC.COM
Page 2 REV A 07/07/20
RF24V1C
Instruction Manual
RF24V1C
GAMAINC.COM
NC
COM
NO
PROGRAM
Programming Switch
Programming LED
Power Terminals
Isolated Output Contacts
Long Range
Antenna Jack
WWW.GAMAINC.COM
Page 3 REV A 07/07/20
To Add Long Range Functionality
The remote control system is equipped with an internal antenna. The expected range in normal conditions is
approximately 100 feet. When additional range is needed, or if the control is placed locations adverse to RF signal
reception, a long range antenna can be added to the system. GAMA Electronics long range antenna, part number LRA-
340, replaces the internal antenna on the system. In normal operating conditions expected range is greater than 500 feet.
If the long range option is purchased with the system, this modification will be made prior to shipment.
To add long range functionality:
1. Plug long range antenna (Part number LRA-340) into the long range antenna jack.
2. Clip the Long Range Antenna Bypass Wire (This will deactivate the internal antenna)
NOTE: It is recommended that you cover the exposed wires with RTV silicone sealant.
NOTE: ONCE THE LONG RANGE MODIFICATIONS HAVE BEEN MADE TO THE SYSTEM THEY CANNOT
BE REVERSED.
Wiring Diagram
RF24V1C
Instruction Manual
PROGRAM
NC
COM
NO
RFR12V1C
GAMAINC.COM
24V DC POWER
SOURCE
Isolated Output Contacts - Independent from the power source
NC - Normally Closed Contact
This terminal is connected to the common
until the receiver is activated by the transmitter
COM-Common
This terminal should be connected to the AC or DC
power that is being switched.
NO - Normally Open Contact
This terminal is connected to the common
when the receiver is activated by the transmitter
Insert Long Range Antenna HereProgram Switch
WWW.GAMAINC.COM
Page 4 REV A 07/07/20
Troubleshooting
All remote-control systems shipped by GAMA Electronics are 100% functionally tested just prior to shipment.
If your RF remote control system does not work out of the box, stops working or functions intermittently please take the
following steps to resolve common issues. Please note that you must be 2-3 feet away from the receiver when operating
the remote control. Operating within 2-3 feet may result in no operation or intermittent operation.
1. Replace the A23 12V Battery in the transmitter
· The remote control can activate during shipping and drain the battery that is installed in the control. We
send a replacement battery with the system if this occurs.
2. Check the voltage supply at the receiver
· The receiver is designed to function at 10-15VDC. Voltage on the (+) and (-) terminals on the control
should be within this range.
3. Reprogram the remote control
· If the system is non-functional try to reprogram the remote control. The program may not have taken
during the programming process or the program button may have been pressed. If the program button is
pressed the memory of the remote controls programed to the receiver are erased.
4. Listen and look for functionality on the receiver.
· The LED that is used for programming the system will illuminate when the receiver is activated. You will
also hear a “click” when the internal relays engage. If you can see the LED illuminate and you hear the
relay “click” the issue is most likely in the wiring or device being controlled.
5. Add a long-range antenna
· If the receiver is in an area that is averse to the reception of an RF signal, such as near a motor or in a
metal casing, a long-range antenna may solve the issue. Connect the antenna per the instructions on
page 3 and mount the antenna in an exposed area away from any motor.
RF24V1C
Instruction Manual
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali GAMA Electronics Ricevitore
GAMA Electronics
GAMA Electronics RF240V-2WP Manuale utente
GAMA Electronics
GAMA Electronics LRF24V1PR-LS Manuale utente
GAMA Electronics
GAMA Electronics LRF240V-2WP Manuale utente
GAMA Electronics
GAMA Electronics RF120VPRDC Manuale utente
GAMA Electronics
GAMA Electronics RF340-DRC Manuale utente
GAMA Electronics
GAMA Electronics RF12V-2-ASL-NIS Manuale utente
GAMA Electronics
GAMA Electronics RF340-100APR Manuale utente
GAMA Electronics
GAMA Electronics RF120V-2WP Manuale utente
GAMA Electronics
GAMA Electronics RF340-400APR Manuale utente
GAMA Electronics
GAMA Electronics RF120VPRDC Manuale utente
GAMA Electronics
GAMA Electronics RF12V-2PR-ASL Manuale utente
GAMA Electronics
GAMA Electronics LRF240VPR1L Manuale utente
GAMA Electronics
GAMA Electronics RF120VPRDC-NIS Manuale utente
GAMA Electronics
GAMA Electronics RF340-4PR-ASL-NIS Manuale utente
GAMA Electronics
GAMA Electronics RF240V-2WP-NIS Manuale utente
GAMA Electronics
GAMA Electronics LRF12VPRWP-WPE-WPTX Manuale utente
GAMA Electronics
GAMA Electronics RF24V-2-ASL Manuale utente
GAMA Electronics
GAMA Electronics RF24V-1PR-ASL Manuale utente
GAMA Electronics
GAMA Electronics RF12V1PR-LS Manuale utente
GAMA Electronics
GAMA Electronics RFR12VPRWP Manuale utente
