Gamma Led Vision TX4 Spot Manuale utente
TX4 Spot
150w Spot Moving Head
User Manual
TX4 Spot – GAMMA LED Vision
Page 1 of 18
Table of Contents
1. Introduction and Setup....................................................................................................................................3
Unpacking and In the Box..............................................................................................................................3
Mounting and Operation................................................................................................................................3
Safety Precautions..............................................................................................................................................7
Customer Support..............................................................................................................................................9
2. Setup and Operation......................................................................................................................................10
Using the LCD Menu and Buttons............................................................................................................10
Menu Operation...............................................................................................................................................10
DMX Setup..........................................................................................................................................................11
DMX Basics....................................................................................................................................................11
DMX Wiring...................................................................................................................................................11
DMX Modes and Configuration.................................................................................................................13
3. Maintenance.......................................................................................................................................................16
Routine Maintenance................................................................................................................................16
Troubleshooting Problems......................................................................................................................17
4. Technical Specifications.................................................................................................................................18
Photometric Data.............................................................................................................................................18
TX4 Spot – GAMMA LED Vision
Page 2 of 18
1. Introduction and Setup
Unpacking and In the Box
Thank you for choosing our TX4 Spot moving head light. For your own safety, please read
this manual before installing or using the device. This manual covers the important
information on installation and applications. Please install and operate the fixture with
following instructions. Meanwhile, please keep this manual for future needs.
The TX4 Spot is made of a new type of high temperature strength plastic and cast
aluminum casing. The fixture is designed and manufactured strictly following CE
standards, complying with international standard DMX512 protocol. It’s independently
controllable and link-able with other lights for operation. And it is applicable for large-
scale live performances, theater, studio, nightclubs, houses of worship, and more.
The TX4 Spot features high brightness and stability. Please carefully unpack it when you
receive the fixture and check for any damages from shipping. And please check whether
the following items are included inside the box:
Mounting and Operation
Caution: For added protection mount the fixtures in areas outside walking paths, seating
areas, or in areas were the fixture might be reached by unauthorized personnel.
TX4 Spot – GAMMA LED Vision
Page 3 of 18
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 items the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is
kept at least 0.5m (1.5ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental
damage and/or injury in the event the clamp fails.
Mounting points: Overhead mounting requires extensive experience, including amongst
others calculating working load limits, a fine knowledge of the installation material being
used, and periodic safety inspection of all installation material and the fixture. If you lack
these qualifications, do not attempt the installation yourself. Improper installation can
result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.
Clamp Mounting: The TX4-150 provides a unique mounting bracket assembly that
integrates the bottom of the base, and the safety cable rigging point in one unit (see the
illustration below). When mounting this fixture to truss be sure to secure an appropriately
rated clamp to the included omega bracket using a M10 screw fitted through the center
hole of the “omega bracket”. As an added safety measure be sure to attached at least
one properly rated safety cable to the fixture using on of the safety cable rigging point
integrated in the base assembly.
TX4 Spot – GAMMA LED Vision
Page 4 of 18
Regardless of the rigging option you choose for your TX4-150 Spot, always be sure to
secure your fixture with a safety cable. The fixture providers a built-in rigging point for a
safety cable on the hanging bracket as illustrated above. Be sure to only use the
designated rigging point for the safety cable and never secure a safety cable to a carrying
handle.
∙The moving head is for spot effect for on-site decoration purpose.
So make sure to operate the fixture until it is in normal temperature.
∙This light should be keep away from strong shaking during any transportation or
movement.
∙Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.
∙Don’t expose the fixture in overheating, moisture or environments with too much dust
when installing it.
∙Make sure the installation environment is in good safety condition before installing the
fixture.
∙Make sure to put the safety chain and check whether the screws/clamps are screwed
properly when installing the fixture.
∙Make sure the lens are in good condition. It’s recommended to replace the units if there
are any damages or severe scratches.
∙Make sure the fixture is operated by qualified personnel who know the fixture before
using.
TX4 Spot – GAMMA LED Vision
Page 5 of 18
∙Keep the original packaging in case there is any future need for any warranty repair or
service.
∙Don’t try to modify the fixtures without any instruction by the manufacturer or the
appointed repairing agencies.
∙Warranty is voided if there are any malfunctions from not following the user manual
while operating or any hazardous operation, like shock short circuit, electronic shock, lamp
broken, etc.
Features
150W High Output White LED
50,000 hour lifespan and lower power consumption
15° Beam Angle with focus function
High light output: 3450LUX@5M in White light
Overtemp protection: When the internal temperature hits 40°C and then the fans
begin to work, if the internal temperature hits 70°C, the brightness reduces to half
until it cools.
Color Wheel: 7 colors +white, rotation with variable direction and speed
1 static Gobo Wheel: 8 gobos +white, wheel rotation and shake
1 Rotation Gobo Wheel: 6 gobos +white, wheel rotation and shake
Prism: 3-facet Prism, bi-directionally rotatable at variable speeds
High speed strobe effect with 1-25 flashers per second
Internal program available
16/14/12/10 DMX Channels USITT DMX-512
DMX 512, master-slave and sound activated controllable or auto operation
Colorful LCD display
Efficient low noise fan cooling system
PowerCon IN/OUT
3-pin XLR connectors IN/OUT
Two 1/4 turn fastening Omega Clamps
IP 20 protection rating
TX4 Spot – GAMMA LED Vision
Page 6 of 18
Safety Precautions
This device has left the factory in perfect condition. In order to maintain this condition
and to ensure a safe operation, it is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes,
do not switch it on immediately. The arising condensation could damage the device.
This light should be keep away from strong shaking during any transportation or
movement.
Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
earthed. The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be
the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power
cord.
During initial start-up some smoke or smell or smell may arise. This is a normal process
and does not necessary mean that the device is defective, it should decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance
with wall for smooth air flow, so there should be no shelter for fans and ventilation for
heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer of his service agent or a similar qualified person in order to
avoid a hazard.
TX4 Spot – GAMMA LED Vision
Page 7 of 18
Don’t expose the fixture in overheating, moisture or environments with too much dust
when installing it. And don’t lay any power cables on the floor. Or it might cause
electronics shock to the people.
TX4 Spot – GAMMA LED Vision
Page 8 of 18
Customer Support
WARRANTY POLICY
GAMMA LED Vision warrants its products for the periods set below from the date of
purchase to be free of manufacturer and workmanship defects. Warranty does not cover
normal wear and tear caused by force, negligence or misuse of products. GAMMA LED
Vision is not responsible for any damages or injury caused by misuse or improper
handling of the products and in accordance with instructions and specifications of manual.
Warranty terms are as follows:
LED Fixtures:
Indoor: 2 Years
Outdoor (IP 54 or higher): 1 Year
Lamp Fixtures: 1 year / excludes the lamp
LED Video Products:
Indoor: 2 Years
Outdoor (IP 54 or higher): 1 Year
Controllers: 2 years
Batteries: 6 months
All Trussing Related Products and Accessories: 1 Year
Please visit WWW.GAMMALEDVISON.COM for complete Limited Warranty terms and
contact information.
TX4 Spot – GAMMA LED Vision
Page 9 of 18
2. Setup and Operation
Using the LCD Menu and Buttons
Menu Operation
TX4 Spot – GAMMA LED Vision
Page 10 of 18
Indice
Altri manuali Gamma Led Vision Riflettore
Manuali Riflettore popolari di altre marche
Guangzhou Yinhe Lighting&Sound Equipment Factory
Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuale utente
LIVARNO home
LIVARNO home 375304 2101 Istruzioni originali
Cameo
Cameo CLQS40WW Manuale utente
Leviton
Leviton Ellipsoid 5/50 Manuale utente
Monacor
Monacor img Stage Line PARL-56PDX/CR Manuale utente
Vector
Vector SL3AKV Manuale utente
EuroLite
EuroLite Akku flat light 1 Manuale utente
Commercial Electric
Commercial Electric SPTM-1401 Manuale utente
Vision & Control
Vision & Control SLB-500-W5K7-P-SL Manuale utente
Teknik
Teknik FLEXI Manuale utente
Craftsman
Craftsman CMXLSB10 Manuale utente
EuroLite
EuroLite LED SLS-144 UV Floor Spot Manuale utente