Garage Smart Hard Top Lifter Manuale utente
USER’S MANUAL
Save this manual for future reference
For a digital version of this manual, visit
www.garagesmart.com/manuals
TABLE OF CONTENTS
SAFETY INFORMATION/ABOUT HARDTOP LIFTER 2
PRODUCT IDENTIFIER 3
WHAT’S IN THE BOX? 4
HARDTOP LIFTER INSTALLATION –TOOLS AND NOTES 5
STEP 1: SMARTTRACK 6
SMARTTRACK TROUBLESHOOTING 7
STEP 2: ASSEMBLY -LENGTH ADJUSTER 8
STEPS 3 & 4: ASSEMBLY -WIDTH ADJUSTER and FOAM BLOCKS 9
STEP 5: ASSEMBLY -PULLEY SLIDER 10
STEP 6: ASSEMBLY –VEHICLE INSTALLATION 11
STEP 7: ASSEMBLY –CARGO NET AND CONFIGURATION 12
STEP 8: ASSEMBLY –ADJUSTMENTS 14
FAQs 16
WARRANTY 17
1
SAFETY INFORMATION
1Read and follow all safety, installation, and operation instructions.
2Do not lift with HardTopLifter while hands or other body parts a near the system.
3Do not stand under the HardTopLifter.
4Do not use HardTopLifter to lift people or animals.
5Do not use HardTopLifter to lift or lower items over people or animals.
6Total lifting capacity for HardTopLifter is 175 lbs.
7Always balance load before lifting.
Failure to follow these safety instructions may result in
property damage, serious personal injury, or death.
WARNING
The HardTopLifter is designed for home and garage use; it is not to be used in commercial or industrial applications.
The HardTopLifter is designed and intended to lift vehicle hard tops off the vehicle and to the ceiling.
ABOUT HARDTOP LIFTER
2
PRODUCT IDENTIFIER
Foam protectors (H)
Not Shown:
Track Cover, Half Size (J)
Cargo net (K)
Long, narrow, width adjusters (E)
Short, narrow, width adjusters (D)
Short, quick-release
pins (G)
Wide, width adjusters (C)
Long, quick-release
pins (F)
Narrow, length adjusters (B)
Wide, length adjusters (A)
Pulley frames (I)
3
WHAT’S IN THE BOX?
Foam protectors
(H) 6x
Cargo net (K) 1x
Long, narrow, width adjusters (E) 2x
Short, narrow, width adjusters (D) 2x
Short, quick-release
pins (G) 8x
Wide, width adjusters (C) 2x
Long, quick-release
pins (F) 2x
Narrow, length adjusters (B) 2x
Wide, length adjusters (A) 2x
Pulley frames (I) 2x
Track Cover,
half-size (J) 1x
4
HARDTOP LIFTER INSTALLATION
Front
Back
The frame should be assembled on the floor, lifted to the
ceiling, and then set down on the roof of the vehicle.
NOTE
TOOLS AND NOTES
•MyLifter (x2)
•Track System (X2)
•Drill
(not shown)
•½” Socket and Wrench
(not shown)
•Stud Finder
(not shown)
REQUIRED TOOLS AND COMPONENTS (not provided)
5
HARDTOP LIFTER INSTALLATION
1. SmartTrack Installation
1. Decide where to place your Hard Top Lifter by parking your
vehicle in that location and assuring that there is enough
space around the vehicle to move and to open doors slightly.
2. Install SmartTracks so each is across two ceiling joists. Place
them 15” apart on center above the vehicle’s intended
location. (Fig 1.1)
3. Mount myLifters on tracks 15” apart. They can be mounted
on the same rail (Fig 1.2a), or on opposite rails (Fig 1.2b),
depending on the direction of the ceiling joists relative to the
vehicle. Each lifter cable will fall along either side of the hard
top.
The carabiners will be hooked to the rails 15” from the
myLifters. This forms a 15-inch square on the ceiling.
4. Pair the Lifters to the App and create a “locked group.” Refer
to the MyLifter Manual for App instructions
Fig 1.1
Fig 1.2a
Fig 1.2b
CAUTION
Be sure to measure the 15-inch square when the
cable is mostly retracted.
SMARTTRACK
Front Back
Front
Back
15”
15”
15”
15”
6
HARDTOP LIFTER INSTALLATION
THESE PICTURES SHOW SEVERAL POSSIBLE PROBLEMS WITH
SMARTTRACK INSTALLATION.
a. Because the clip was placed on the wrong side, the
lifter will misalign the hard top.
b. Spacing isalso incorrect (18”) when cable is
retracted.
c. These two hooks are also misaligned when the lifter
is retracted.
d. Placing the clip on the wrong side of the track will
cause the wrong spacing.
e. Cable wraps under the lifter.
SMARTTRACK TROUBLESHOOTING
18”
17”
13”
(a)
(b)
(c)
(d)
(e)
7
5. Power Adapter Layout
1. Depending on your orientation, Power Adapters
can be laid out as shown or in other
configurations. (Fig 1.5.1)
If there are no outlets near the lifters, the power
adapters can be placed on a separate track or on
a stud. (Fig 1.5.2)
Fig 1.5.1 Fig 1.5.1
ASSEMBLY
HARDTOP LIFTER INSTALLATION
2. Length Adjuster
1. There are four length adjusters (each with 34 holes), two
narrow (B) and two wide (A). Lay the narrow ones inside
the wide ones with the square holes at opposite ends.
(Fig 2.1a)
Both u-shaped bars open upward. These will later be
pinned in place. (Fig 2.1b)
2. Slide the width adjusters (C) through the square holes as
shown. Align holes with length adjuster openings as
shown. (Fig 2.2)
3. Assemble all six pieces together. (Fig 2.3)
Fig 2.3
Fig 2.1a
Fig 2.2
Fig 2.1b
8
Altri manuali per Hard Top Lifter
1
Indice
Altri manuali Garage Smart Sistema di sollevamento
Garage Smart
Garage Smart myLIFTER Istruzioni operative
Garage Smart
Garage Smart Multi-Bike Lifter Manuale utente
Garage Smart
Garage Smart Universal XL HD Lifter Manuale utente
Garage Smart
Garage Smart Hard Top Lifter Istruzioni operative
Garage Smart
Garage Smart MY LIFTER BASIC LIFTER Manuale utente
Garage Smart
Garage Smart UNIVERSAL LIFTER Manuale utente
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
