Operating Instructions
1.
Unpack the machine and take it out from the base plate.
Place the machine on ground and mount cleaning
scrubber.
2.
As
shown
in
Fig.
1,
adjust the angle adjustment pull
handle to 90 °- 120
°.
Then, remove the clear water tank.
Unlock the two clamps on the battery compartment
at
the
back
of
machine and connect the battery to a fixed socket.
3. Install the battery compartment cover and clear water
tank. Add
an
appropriate quantity
of
cleanser solution.
4.
Install the sewage
tank
to the hook on the aluminum
pipe ofoperating handle, and connect the suction pipe and
sewage pipe to the sewage tank.
5.
Put down the suction head UP/DOWN handle on the
back
of
machine (Fig. 3).
In
this case, the suction head
has been flatly placed on the ground. Pull the angle
adjustment handle to adjust operating handle to the height
desired
by
the operator. Then, release the handle.
6.
Put the main scrubber switch
(I),
pumping switch (2)
and solenoid valve switch (3) on the panel
of
operating
handle to "ON" position. Check
if
the signal lamp is
bright (green). Then, push the safety lock on operating
han
dle to center, and closethe hand-operated switch, so
that the machine will start to work.
Fig.2
Care and Maintenance
@ I.Main
scrubber
switch
2.Pumping switch
3.Solenoid valve
switch
To extend the service life
of
the machine and enable the machine to work under the best effect,
it is suggested to do the following after each use:
1.
Use
clear water to wash the suction head clean and wipe with dry cloth.
2. Remove the sewage tank and use clear water to wash it clean. At the
same
time, use water to
rinse the suction pipe clean.
3. This machine cannot be wash directly with water,
but
be wiped with semi-dry cloth, thus to
ensure that no water will enter into the machine. Otherwise, the electric parts
of
the machine
will be burnt.
4.When the machine is to be put long out
of
service,
the battery shall be reguJarly recharged;
01herwise the service life
of
the battery will be reduced.
2
Main Troubles and How to Solve Them
Trouble Cause
How
to Solve
The
power
socket is not properly Connect the power socket
No
power
supply connected properly
The
main scrubber switch is not Check and put
it
to
ON
put to
ON
position. position.
The
suction pipe is blocked Check and wash the suction
pipe
No
suction force
or
the
The
sewage tank cover is not Reinstall and seal the
suction force is low installed properly sewage tank
cover
properly
The
pipe connection is not tight
Check
and repair
The
suction carbon brush is worn Replace the carbon brush
The
hand-operated
power
switch Replace the
power
switch
The
scrubber motor is burnt Repair
or
replace the
motor
cannot rotate after it is
The
scrubber motor is burnt Repair
or
replace the circuit
energized
The
circuit board is failed board
The
carbon brush
of
motor is Replace the carbon brush
of
worn motor
The
carbon brush
of
motor
is
Replace the carbon
The
suction motor worn brush
cannot rotate after it
The
motor is short circuited Repair
or
replace
is
energized and burnt Repair
or
replace the
The
circuit board is failed circuit board
The
battery
is
short circuited Replace with a new
or
aged battery
The
battery cannot
be
The
recharging circuit is short Repair
or
replace
the
recharged circuited
or
burnt recharger
The
insert connecting the Check and repair
recharger is in poor contact
The
circuit board is failed Repair
or
replace
The
solenoid valve is short Replace
tl1e
solenoid
There
is no water out circuited valve
during working
The
drain pipe is blocked Check and clean the pipe
The
drain switch is not put to Check and put it to
ON
ON
position. position.
Included Accessories
1.Machine, 1set
2.
Groundscrubber, 1
pc
3.
Sewage tank, 1 pc 4. Clear water tank, 1pc
5.
User Manual, 1 copy
3
