GE ImageQuant LAS 500 Istruzioni operative
ImageQuant™LAS 500
Site Preparation Guide
Table of Contents
31 Introduction ..........................................................................................................
52 Site preparation overview ..................................................................................
103 Site preparation checklist ..................................................................................
2 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA
Table of Contents
1 Introduction
Purpose of this document
The purpose of this document is to give the information you need to fully prepare your
site for the installation and testing of the system.
A Site preparation checklist is included in this document.
Scope of this document
This Site Preparation Guide covers the ImageQuant LAS 500 imager.
Preparation
Make sure to read the entire Site Preparation Guide and complete the Site preparation
checklist in Chapter 3.
If GE support is needed, return the completed Site preparation checklist to the GE service
office in your region. You will find E-mail address and fax number to the GE service office
in your region under www.gelifesciences.com/contact. If your region is not listed, select
the nearest region.
ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA 3
1 Introduction
Assign personnel for site
preparation tasks
The site preparation tasks listed in the following table can be divided between two or
three people from the customer.
Site preparation tasksPersonnel
Site preparation/
installation
coordinator
•Review the site preparation guide for safety information and system re-
quirements.
•Choose the site.
•Coordinate personnel and tasks.
•Coordinate the installation timing of the system with any domestic safety
procedures and testings.
•Order required materials.
•Schedule the installation and inform personnel of the installation date.
Laboratory personnel/
Primary users •Review the safety information.
•Make sure that all customer-provided materials for the installation are
present at the site.
Facilities personnel •Make sure that the installation requirements are met for:
-Space at the installation site
-Environmental conditions
-Biosafety
-Ventilation and waste collection
-Electrical supply
-Safety and installation materials
4 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA
1 Introduction
2 Site preparation overview
Introduction
Before the product is delivered, you must prepare the site according to the instructions
in this chapter.
Select the site
Select a site that complies with national and international requirements for biosafety.
WARNING
Spread of biological agents. The operator has to take all necessary
actions to avoid spreading hazardous biological agents. The facility
must comply with the national code of practice for biosafety.
General site requirements
The following requirements must be fulfilled at the location where the ImageQuant LAS
500 imager will be installed:
•There must not be a heat source such as a radiator near the imager
•There must be no risk that the imager can get wet or flooded
•The imager must not be exposed to corrosive gas
•The imager must not be installed in a dusty environment
•The imager must not be installed in a place which is constantly or exessively exposed
to vibration or impacts.
•The imager must not be exposed to direct sunlight
ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA 5
2 Site preparation overview
Space requirements
Prepare a clean working area on a stable laboratory bench. The bench must comply
with the specifications in the following table.
SpecificationParameter
60 x 60 cmMinimum bench area for operating
ImageQuant LAS 500
At least 20 cm free space in front of the
imager.
Free space required around the imager
10 cm free space on all other sides.
490 N (50 kg) or higherLoad capacity
Horizontal ±2°Inclination of bench surface
WARNING
Access to power cord. Do not block access to the power cord. The
power cord must always be easy to disconnect.
There must be additional space on the bench to place samples on the tray.
Note:
6 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA
2 Site preparation overview
Dimensions and weight
The following illustration shows the dimensions of the ImageQuant LAS 500 imager.
570 mm
280 mm
300 mm
The ImageQuant LAS 500 imager weighs 15 kg.
Environmental requirements
ImageQuant LAS 500 is intended for indoor use only.
The installation site must compliy with the following specifications:
SpecificationParameter
18°C to 28°CAmbient temperature, operation
Temperature fluctuation < 10°C per hour
15% to 70% RH, non-condensingRelative humidity, operation
-25°C to 70°CAmbient temperature, transportation/stor-
age
5% to 95% RH, non-condensingAmbient humidity, transportation/storage
ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA 7
2 Site preparation overview
SpecificationParameter
(1) Operating time Oscillation: 0.03G (5 to
60 Hz)
Floor vibration conditions
Impact :1G
(2) Non-operating time Oscillation: 0.4G
(5 to 60 Hz)
Impact :2G
Up to 2000 mAltitude, operation
Pollution degree 2Pollution degree of the environment
CAUTION
Do not use the instrument in a room with a temperature above
+28°C. Higher temperature does not allow the CCD to cool down
properly (to -25°C).
Electrical requirements
SpecificationParameter
100 to 240 V AC ±10%Supply voltage
50/60 HzFrequency
200 WMax power
Overvoltage category IITransient overvoltages
WARNING
Protective ground. The product must always be connected to a
grounded power outlet.
8 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA
2 Site preparation overview
User-supplied accessories and
consumables
The following accessories must be supplied by the user:
Personal Protective Equipment (PPE) as required (gloves, lab coats, etc.).
Other product specifications
SpecificationParameter
70 dB(A) or lowerNoise
Fast Lmax ≤60dB(A), and average Leq ≤ 54dB(A)
(1 m from the instrument)
IP21Protection provided by the enclo-
sure
ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA 9
2 Site preparation overview
3 Site preparation checklist
Introduction
Read the previous chapters in this Site Preparation Guide before completing the checklist.
Complete the checklist in this chapter to make sure that all necessary preparations have
been made for the installation of ImageQuant LAS 500.
Checklist
Comment/specifyN/ANOYESRequirement
General
If GE support is needed for installation, will the GE
service personnel be required to take site EHS
(Environment, Health and Safety) or security
training before doing the installation?
Assigned personnel
Personnel are assigned as specified.
Site selection
Site complies with requirements for
biosafety
General site requirements are fulfilled
Space requirements
Space is available as specified.
Imager
Accessories/additional components
Environmental requirements
The proper environmental conditions are fulfilled
as specified.
Ambient temperature
Relative humidity
10 ImageQuant LAS 500 Site Preparation Guide 29-1358-76 AA
3 Site preparation checklist
Altri manuali GE Attrezzature da laboratorio
GE
GE AKTA ready Manuale utente
GE
GE SE 250 Mighty Small II Manuale utente
GE
GE AKTApure Manuale utente
GE
GE AKTA GO Manuale utente
GE
GE 800 Manuale utente
GE
GE LOGIQ S7 Expert Manuale utente
GE
GE AKTApure Manuale utente
GE
GE AKTApilot Istruzioni operative
GE
GE Ettan IPGphor 3 Manuale utente
GE
GE pH/C-900 Manuale utente
GE
GE Monitor UV-900 Manuale utente
GE
GE AKTA avant Manuale utente
GE
GE Frac-920 Manuale utente
GE
GE AxiChrom 50 Manuale utente
GE
GE AKTApure Manuale utente
GE
GE akta start Manuale utente
GE
GE Amersham Imager 600 Manuale utente
GE
GE AKTA Prime Plus Manuale utente
GE
GE OptiSonde Manuale utente
GE
GE akta start Guida
Manuali Attrezzature da laboratorio popolari di altre marche
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuale utente
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuale utente
NI
NI PXI-5422 Manuale
Collomix
Collomix Aqix Manuale utente
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente
Ocean Insight
Ocean Insight FLAME-NIR+ Manuale utente
