GE CWLSWDMBWF1 Manuale utente
™
Wire-Free
Smart Switch
Installation Guide
Models
CWLSWDMBWF1
CWLSWCCBWF1
Download
the C by GE app
Install
your Smart
Switch
Add
your Wire-Free
Smart Switch to the
C by GE app
Simple DIY Setup
Compatibility Requirements
Works with C by GE Smart Lights, Plugs, Switches, and Sensors.
Not compatible with non-C by GE Smart devices.
NOTE: Switch and other C by GE lights, plugs, and
switches must be grouped in the same Room/Space in
the C by GE app to enable full room control.
Let’s Do It
INCLUDED
YOU’LL
NEED
OPTIONAL
Switch
Wall Plate 4 Phillips
Mounting Screws
Drywall
Anchors
Adhesive
Tape
Phillips Screwdriver
Drill w/ 7/32 bit Level
Tape Measure
You Got This!
And we’re here to help.
For in-depth instructional videos
and a guided tour through the installation,
go to cbyge.com/wirefree-support.
BEFORE YOU DO ANYTHING: Step 1
Location & Mounting Type
Decide how you want to mount your switch
This switch can be mounted to the wall in two ways, by screws or adhesive tape.
Once you determine which install method is best for you, select one of
the following setup methods.
IMPORTANT
Start by removing the clear plastic tab
from the back of the switch.
1. Identify where you want to mount your Wire-Free Switch (switches are
typically located 48-52” from the floor to the top of the switch).
2. Prior to installation, be sure that the surface is smooth and degreased.
3. Apply adhesive tape to the middle back of the switch. Adhesive tab
should stick out from the side of the switch. This will be covered by
the wallplate and allows removeal if needed in the future.
4. Mount switch to the wall.
5. Screw on the faceplate bracket, then snap the faceplate cover
onto the bracket.
STEP 2 - Mounting with adhesive tape
Installing Your Switch
STEPS 1 & 2
STEPS 3, 4 & 5
IMPORTANT
Start by removing the clear plastic tab
from the back of the switch.
1. Identify where you want to mount your Wire-Free Switch (switches are
typically located 48-52” from the floor to the top of the switch).
2. Mark the location for holes to be drilled. We suggest using the
mounting holes on the switch housing as a guide. Use the level (optional)
to ensure the switch is level before drilling holes.
3. Using 7/32” bit, drill holes in wall for mounting screws.
Insert drywall anchors.
4. Secure the switch to the wall until level and flush.
5. Screw on the faceplate bracket, then snap the faceplate cover
onto the bracket.
STEP 2 - Mounting with screws/single-gang wallplate
Installing Your Switch
STEPS 1 & 2 STEPS 3
STEPS 4 & 5
Altri manuali per CWLSWDMBWF1
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali GE Interruttore
GE
GE Multinet 4 Manuale utente
GE
GE MultiLink ML1200 Manuale utente
GE
GE BreakMaster Manuale di istruzioni
GE
GE Reason H49 Manuale utente
GE
GE "Executive Series" USB 2.0 HO97864 Manuale utente
GE
GE GuardSwitch 300 Series Manuale utente
GE
GE 15132 Manuale utente
GE
GE 97845 Manuale utente
GE
GE BM-C303US5-04 Manuale utente
GE
GE VMIACC-5595 Series Manuale utente
