Genie WAHD324H Manuale utente

Quick Start Guide

Please read these instructions carefully before operating the unit

and keep for further reference.

32 Channel 4-in-1 High

Deﬁnition DVR with 4HDD Bays

WAHD324H

Intro Section

Please read this instruction carefully before operating the product and keep it for further

reference. All examples and pictures used here are for reference only.

The contents of this manual are subject to change without notice.

CAUTION:

• Please check the device and the accessories after getting the device. If there are any

damages, shortages or defects, please contact your dealer immediately.

Contents

iii

1.0 Introduction..........................................................................................................4

1.1 Product Features...........................................................................................4

1.2 Product Dimensions.....................................................................................4

1.3 Speciﬁcation.................................................................................................5

2.0 HDD Installation...................................................................................................6

3.0 Rear Panel Instruction..........................................................................................7

4.0 Start Up and Shut Down......................................................................................8

5.0 Login ....................................................................................................................9

6.0 Conﬁgurations and Connections ........................................................................10

6.1 Ananlogue Camera Connection...................................................................10

6.2 Network Conﬁguration & Adding IP Camera..............................................10

7.0 UPnP .....................................................................................................................12

8.0 NAT.......................................................................................................................13

9.0 Manual Recording and Playback .........................................................................14

9.1 Manual Recording.........................................................................................14

9.2 Playback.......................................................................................................14

The Genie WAHD324H is a 32 channel 1080p H.264 high deﬁnition DVR. The DVR supports

32 channel video input, 4 channel audio input and 16 channel simultaneous playback. It is

iPhone and Android compatible with an app (Super Live Plus) available with free Windows

/ MAC CMS software supplied.

1.1 Product Features

• 32 CH TVI / CVI / AHD video input

• 32 CH 1080p / 1080p Lite / 720p / WD1 recording

• H.264 high proﬁle compression format for high quality video at much lower bit rate

• Intuitive and user friendly graphics user interface (GUI), window style operation by

• mouse

• Multi-mode recording: Manual / Timer / Motion

• Playback : 16 CH simultaneous playback

• Search: Time slice, Time, Event (Manual, Motion), Tag Search

• Express and ﬂexible backup via USB, network etc.

• Pentaplex : Preview, Record, Playback, Backup and Remote Access

• DHCP, DDNS, PPPoE Network Protocol, IE browser and CMS supported

• Remote control via Web or CMS : Preview, Playback, Backup, PTZ and Conﬁguration

• Dual stream technology for local storage with high deﬁnition, remote network

transmission and remote surveillance with mobile device

• Multi-user online simultaneously

• P2P ready for hassle free remote access

• Authorisation management, log review and device status review

• Supports HDMI 1080P output, true high resolution display

• Supports PTZ preset and auto cruise, up to 255 presets and 8 cruises

• Supports NAT function and QR code scanning by mobile phone and iPad

• Powerful smart phone & iPad surveillance with iOS and Android OS

1.2 Product Dimensions

1.0 Introduction

440mm

390mm

70mm

Quick Start Guide 32 Channel 4-in-1 High Deﬁnition DVR with 4HDD Bays

1.3 Speciﬁcation

Model WAHD324H

System OS Embedded Linux

CPU Cortex A9

Video

Input BNC x32

Output

HDMI x 1 : 1920×1080,

VGA x 1 : 1920×1080,

BNC x 1 : CVBS (Used as the main or spot output)

Resolution TVI / CVI / AHD 1080p, 720p, WD1 real-time

Compression H.264 / H.265

Audio

Input RCA x 4

Output RCA x1

Two-Way Audio Yes

Mobile Device OS iOS, Android

Storage HDD HDD : SATA x 4, Max. 6TB per HDD

Playback

Playback 16 CH

Search Time Slice / Time / Event / Tag Search

Smart Search Highlighted colour to display the camera record in a certain period of time, different

colours refers to different record events.

Function Play, Pause, FF, FB, Digital Zoom, etc.

Alarm

Mode Manual, Motion, Exception

Input 4

Output 1

Triggering Record, Snap, Preset, E-mail etc.

Network Interface RJ45 10M / 100M / 1000Mbps x 1

Protocol TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP

Record

Resolution 1080p, 1080p Lite, 720p, WD1

Frame Rate

1080P : 12fps (PAL) / 15fps (NTSC)

1080P Lite / 720p

WD1 : 25fps (PAL) / 30fps (NTSC)

Bit Rate 768Kbps ~ 8Mbps

Mode Manual, Timer, Motion, Sensor

Remote

Monitoring

Immix Compatible with Immix via RTSP only (2-way audio not supported)

Sentinel Yes, Firmware 1.1.0 or later

Backup Local Backup USB stick, USB mobile HDD

Network Backup Yes

Port

RS485 RS485 × 1, connect to PTZ or keyboard

USB USB 2.0 × 1 (In the front panel),

USB 3.0 × 1 (In the rear panel)

Remote Controller Optional

Others

Power Supply ATX250W

Consumption ≤ 20W (Without HDD)

Working Environment -10~50°C, 10%~90% (Humidity)

Dimensions 440 × 390 × 70 mm

This series of the product supports 4 SATA hard drives. Please make sure that the device is

powered off before the installation. The pictures of the installation are only for reference.

1. Loosen the screws to open the cover.

2. Screw two screws into the holes of HDD but not don’t tighten them.

3. Turn over the machine and place the HDD with two screws onto the bottom of the

case. Then lock the screws according to the order of the marks.

4. Install the other three HDDs according to above-mentioned method.

5. Connect the power and data cables.

6. Install the cover back and ﬁx it.

Note: Please check the inside structure of the device and make sure that the cables are

connected well before installing the cover back. Please format the HDD before using.

2.0 HDD Installation

The interfaces of the rear panel are for reference only.

3.0 Rear Panel Instruction

Name Description

VGA Connect to monitor

HDMI Connect to high deﬁnition display device

LAN Network port

USB Connect to USB storage device or USB mouse

ALARM IN Alarm input for connecting sensor

ALARM OUT Relay output, connect to external alarm

GND Ground

P/Z Connect to speed dome. Y is TX+,Z is TX

K/B Connect to keyboard. A is TX+,B is TX

AUDIO OUT Audio output

AUDIO IN Audio input

e-SATA Connect to HDD with e-SATA interface

Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

Shutdown

Go to “Main Menu” and then select “Shutdown” icon. This will bring up a shutdown

window. The device will shut down by clicking “OK” button. Then disconnect the power.

4.0 Start Up and Shut Down

The default username is admin and the default password is 123456. You must conﬁgure the

wizard if you start the DVR for the ﬁrst time and you may change the password when you

conﬁgure the wizard for the ﬁrst time. You can skip the settings wizard next time.

Click “Start” and select “Login”. This will take you to see a login box. Enter the default

username and password you set. Then you will see the live image.

5.0 Login

6.1 Ananlogue Camera Connection

First connect the camera to the DVR.

Then go to Start → Settings → Camera→ Manage Camera → Camera Signal to checkmark the

video mode. Theactual signals input shall correspond to the video mode. Please refer to

the User Manual for details.

6.2 Network Conﬁguration & Adding IP Camera

After you ﬁnish adding IP cameras, you can see the live images through the monitor of the

DVR. The following will mainly introduce how to add the IP cameras via LAN/WAN.

LAN

1. Set the network of the DVR. Go to Start → Settings → Network → TCP/IP. Enter IP

address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the

DVR and the router.

2. Go to Start → Settings → Network → Port. Enter HTTP port (the default value is 80),

server port (the default port is 6036).

3. Click “Apply” to save the settings.

4. Go to Start → Settings → Camera → Add Camera. The DVR will automatically refresh the

cameras searched. The IPC which supports the Onvif protocol may be added manually.

If the IPC searched is not in the same local network as the DVR, you should select the

device and click to modify the IP address.

6.0 Conﬁgurations and Connections

Indice

Manuali Registratore digitale popolari di altre marche

FLIR

FLIR M3100E Series Manuale utente

VTRACKPRO

VTRACKPRO FPRO300 Manuale utente

Swann

Swann NVR-7085 models Manuale utente

XtendLan

XtendLan DVR-1670C Manuale utente

urmet domus

urmet domus 1093/004AHD Manuale utente

Holux

Holux M1 Manuale utente

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuale utente

Whistler

Whistler D16VRS Manuale utente

Defender Security

Defender Security 82-20235 Manuale utente

MISUMI

MISUMI MP-WF100M Manuale utente

Speco

Speco D8HU Manuale utente

UST

UST DDR-E04AA Istruzioni per l’uso

Consolidated

Consolidated Digital Video Recorder Manuale utente

Mace

Mace DVR0404RW Guida rapida

RCA

RCA RTD315W Manuale utente

FSM

FSM Colibri Grande PRO Manuale utente

Hauppauge

Hauppauge HD PVR 2 Manuale utente

Identivision

Identivision ICR-PH161i PIONEER Manuale utente