Genie IPC2 Manuale utente
IPC2
Full HD IP Bodied Camera
User Manual
Safety Information
Precaution
This exclamation point symbol is
intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions
in the literature accompanying the
appliance.
Precaution
This exclamation point symbol is
intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions
in the literature accompanying the
appliance.
Warning
1. Be sure to use only the standard adapter that is
specified in the specification sheet. Using any
other adapter could cause fire, electrical shock, or
damage to the product.
2. Incorrectly connecting the power supply or
replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single
adapter. Exceeding the capacity may cause
excessive heat generation or fire.
4. Securely plug the power cord into the power
socket. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and
firmly. A falling camera may cause personal injury.
6. Do not place conductive objects (e.g. screw
drivers, coins, metal items, etc.) on top of the
camera. Doing so may cause personal injury, fire
or electric shock.
7. Do not install the unit in humid or dusty locations.
Doing so may cause fire or electric shock.
8. If any unusual smells or smoke comes from
the unit, stop using the product. Immediately
disconnect the power source and contact the
service centre. Continued use in such a condition
may cause fire or electric shock.
9. If this product fails to operate normally, contact
the nearest service centre. Never disassemble or
modify this product in any way.
10. When cleaning, do not spray water directly into
parts of the product. Doing so may cause fire or
electric shock.
Precaution
Operating
• Before using, make sure power supply and
all other parts are properly connected.
• While operating, if any abnormal condition
or malfunction is observed, stop using
the camera immediately and contact your
dealer.
Handling
• Do not disassemble or tamper with parts
inside the camera.
• Do not drop the camera or subject it to
shock or vibration as this can damage the
camera.
• Clean the clear dome cover with extra care
Scratches and dust can ruin the quality of
the camera image.
Installation and Storage
• Do not install the camera in areas of
extreme Temperature which exceed the
allowed range.
• Avoid installing in humid or dusty
environments.
• Avoid installing in places where radiation is
• present.
• Avoid installing in places where there are
strong magnetic fields and electric signals.
• Avoid installing in places where the camera
would be subject to strong vibrations.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
Important Safety Instructions
1. Read these instructions - All safety and operating instructions should be read before the product is
installed or operated.
2. Keep these instructions - The safety, operating and user instructions should be retained for future
reference.
3. Heed all warnings - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions - All operating and user instructions should be followed.
5. Clean only with a dry lint free cloth - Unplug this product from the power source before cleaning. Only
use neutral detergents.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions - Slots
and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and
to protect it from overheating.
7. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including
amplifiers) that produce heat.
8. Protect the power cord from being walked on or pinched, particularly where they exit the product.
9. Only use accessories specified by the manufacturer.
10. Only use with brackets specified by the manufacturer, or sold with the apparatus.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, does not operate normally, or has been dropped.
Product & Accessories
Introduction -
Quick Manual
NOTE:
The C-Lens and CS-Lens are not included in the product package. C-Lens and CS-Lens is optional.
Manual CD
Please check if camera and accessories are all included in the product package.
Camera
Camera Holder MountC-Mount Adaptor Camera Holder
Screw-2pcs
4
Part Name
Introduction -
2
1
5
3
4
6
7
Micro SD Memory Card Slot
Covers the inner cover, lens, and main body to protect them.
Power Indicator
When the power turns on, the indicator will light on.
RJ-45 Connector
Used to connect a PoE or LAN cable.
GND
Used for earth-grounding.
Audio In/Out Port
Used to connect the audio in/out cable.
BNC Video Port
Used to connect video output device such as monitor using
the BNC coaxial cable.
Factory Reset Switch
All the settings will be restored to the factory default. Power
On the unit and push the switch for 5 seconds.
WARNING:
YOU WILL LOSE ALL DATA THAT HAD BEEN ENTERED PREVIOUSLY AND
THE IP DOME CAMERA WILL BE SET TO ITS FACTORY RESETS.
8
9
10
11
12
13
Power Port
Use the screwdriver to connect each line (+, –) of the power
cable to the corresponding power port of the camera.
WARNING:
Be careful not to reverse the polarity when you connect the power cable.
You can also use a router featuring PoE (Power over Ethernet) to supply
power to the camera.
Alarm Input/Output Port
Used to connect the alarm input/output signal.
Only 2M camera support the RS-485port.
Camera Holder (Mount) Holes
Used when you mount the camera onto the bracket by
fixing the camera holder (mount) adaptor with the bracket.
Lens Connector Port
Installed on the lens adaptor.
Back Focus Conctrol Lever
Used to connect the lens connector which output the power
and control signal to control the iris of lens.
Auto Iris Lens (Optional)
Used to control back focus for the lens.
Rear Side
Front Side
9
8
7
5
6
1
2
3
4
10
11
12
13
5
Introduction -
Specication
Features and specications are subject to change for further improvement without any notice
Model Number IPC2
Image Sensor 1/2.8” 2MP CMOS
Resolution 2MP
Minimum Illumination Colour: 0.5 Lux
B&W: 0.01 Lux
Day / Night AUTO / DAY / NIGHT
Focus Manual
Shutter Speed 1/25 ~ 1/30,000 Sec
AGC YES
WDR YES
BLC YES
DSS YES
DNR YES
Sensor I/O 1 Input / 1 Output
Video Output BNC: VBS 1.0 Vp-p
Material Aluminum Die-Casting
Video Compression H.264 / MPEG4 / MJPEG
Video Streaming VBR / CBR
Video Resolution 1080p / 720p / D1 / CIF / QCIF
Frame Rate 30 fps for 1080p
Audio Compression Two Way, G.711 PCM. μ-law 64kbps 8kHz
Local Storage SD Card (Not Included) - JPEG Capture Only
Power DC12V / PoE
Temperature -10°C ~ 50°C
Support Protocol IPV4 / IPV6 / DDNS / SECURITY
Onvif YES
Dimensions (W x H x L) 75 x 60 x 125 mm
Weight 0.45Kg
6
Installation
Installation -
2
1
Disconnect the power before proceeding.
Mounting the Lens
CS-Lens: Turn the optional CS-Lens clockwise to
insert it.
C-Lens: Turn the C mount adaptor clockwise to insert
it and do the same with the C-Lens.
CS-Lens
C-Lens
Fix the Camera Holder
By tightening two camera holde screws provided,
attach the camera holder on the camera.
7
3
5
4
Adjusting Zoom and Focus
By turning screws of the lens, adjust the Zoom and
Focus after setting the position and view angle of
camera.
Lens Connector
Connection Lens Connector
Connect the lens control cable to the lens connector.
Connecting Cables
Connect the power, video, audio, alarm and network
cables respectively. See the section ‘Installation -
Cabling’ for detail.
Installation
Installation -
8
4
5
6
7
Sensor/Alarm Input
It connects to IR sensor, IrDA sensor or door switch. If the
sensor is activated, it can activate to move camera to the
specific angle and to connect the alarm device.
Relay Output
It connects to the alarm lights, siren or lamps.
RS-485(2M Camera Only): Controls with device using RS-485
communication standards.
Audio In
Connect the ‘Audio In’ port of the camera to the
microphone directly or ‘Line Out’ port of the amplifier
connected with microphone.
If the microphone is connected directly, the microphone with the
embedded amplifier such as condenser mic. needs to be used.
Audio Out
Connect the ‘Audio Out’ port of the camera to the ‘Line In’
port of the speaker.
If the speaker without the amplifier is connected to Audio Out
port, it doesn’t work properly. Therefore, the speaker with the
amplifier or the separate amplifier is needed.
1
3
2
Network Connection
Connect the crossover cable into the RS-45.
Video Output(BNC Cable)
The BNC cable is used to connect to a monitoring display.
Power Connection
Please, check the voltage and current capacity of rated
power carefully.
Rate Power Current Consumption
DC 12V 5.5W
PoE
IEEE802.3af Class 0
2Video Output(BNC) 3Power
1Network
Connection
4Sensor/
Alarm Input
5Relay Output
Amplifier
Mic.
Speaker
Line In Connection
Line Out Connection
Direct Connection
Mic.
RS-485
Cabling
Installation -
7Audio Out
6
Audio In
9
Micro
Inserting/Removing an SD Memory Card
Installation -
1Inserting an SD Memory Card
Insert the SD card in the arrow direction.
Don’t insert the SD memory card while it’s upside down by force.
Otherwise, it may damage the SD memory card.
2Removing an SD Memory Card
Removing an SD Memory Card Gently press down on the
exposed end of the memory card as shown in the diagram
to eject the memory card from the slot.
Pressing too hard on the SD memory card can cause the card to
shoot out uncontrollably from the slot when released.
If you have saved data in the SD memory card, removing the SD
memory card prior to setting record to OFF will cause damage to
the data stored in the card.
Recommended SD Card Specication (Not Included)
- Type: Micro SD (SDHC)
- Manufacturer: Transcend, Kingston, Toshiba, Sanddisk
- Capacity: 4~16G
- Class: over Class 6
The memory card is an external data storage device
that has been developed to oer an entirely new way
to record and share video, audio, and text data using
digital devices.
10
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Genie Telecamera IP
