Gesipa Taurus 3 Guida all'installazione

TAURUS 1-2-3

Repair Instructions

GESIPA Blindniettechnik GmbH

Nordendstraße 13-39

D-64546 Mörfelden-Walldorf

Telefon +49 6105 / 962-0

Telefax +49 6105 / 962-287

Internet http://www.gesipa.com

E-Mail [email protected]

This document shows the chronology of the disassembling of the Taurus tool

series, illustrated by corresponding pictures. This operation necessitates the use

of special tools which are separately listed. Special procedures which must be

followed are described in details and pictured. Reference is also made to the

operating instructions booklet as well as to the illustrated parts price list.

• Disconnect the tool from the air pressure supply

• Unscrew head (24)

• Unscrew jaw housing (16)

• Unscrew rest mandrel container (103/104)

• Unscrew pressure pipe screw (43a,43) with spring washer (49)

• Re-install the rest mandrel container (103/104)

1

• Pull-off adapters (42) with lock (41) and retaining spring (48) using the

rest mandrel container itself

• Important: Remove the housing screw from tool bottom. This screw is

maintaining the tool bottom in place and prevents its separation from the

tool.

2

•Carefully install the main cylinder in a vice.

•Unscrew tool bottom (76,77,78) using a wrench for twin holed nuts

according to DIN 3116.

•Install the tool into the clamping jig ( Special tool )

•Extract the aluminium cylinder(69,70,71)

3

Extract the air piston (72,73,74) using a plier

•Unscrew Alu nut (57) using the special wrench P/N: 143 5672

4

•Carefully remove the complete air cylinder housing (58,59,60) from the

aluminium tube

•Take great care of not damaging O- Ring (56) !

•Unscrew the rear screw plug (40) using special wrench P/N 144 6031

5

•Remove the tool head from the clamping jig

•Remove the complete grip section

•Empty the hydraulic fluid into an adequate container

6

•Push traction rod (25) backwards out of the tool head

•Remove reset plunger (36) from the traction rod

•Use a 17mm dia. Alu or plastic stamp for removal of the sealing ring

holder (32

•Plug the stamp into front of tool head and eject carefully the sealing ring

holder using a light hammer.

7

Proceed as follows in case the control valve (see cut A-A in operating

instructions)has to be removed from the air cylinder housing (58,59,60):

•Remove screw (75) using a T20 Torx screw driver

•Unscrew the safety valve (90) using an adequate screw driver

8

•Use an adequate tool to push out the control piston (92) and the plug

(96,97,98) from the side of the safety valve

•Push the airzet rod sealings (93) and spacer cage (91) out of the air

cylinder housing.

•Order of sequence of the different components of the control valve.

9

Questo manuale è adatto per i seguenti modelli

2

Altri manuali Gesipa Utensili per rivetti

Manuali Utensili per rivetti popolari di altre marche

FAR

FAR RAC 182 Manuale utente

Stanley

Stanley ProSet XT4-AHR Manuale utente

YATO

YATO YT-3617 Manuale utente

CHIEF

CHIEF PNP 90 UN 2.0 Manuale utente

Gage Bilt

Gage Bilt GB150 Manuale utente

JRP

JRP NB80A Manuale utente

Würth

Würth ANG 14 Guida rapida

Ingersoll-Rand

Ingersoll-Rand 127 Manuale utente

Arconic

Arconic MARSON MP-4V Manuale utente

Sealey

Sealey CP316 Manuale utente

Silver Eagle

Silver Eagle SE314 Manuale utente

Würth

Würth HES 510 N Guida rapida

Stanley

Stanley EZM1000 Guida alla risoluzione dei problemi

Stanley

Stanley PROSET PB3400 Manuale utente

HS-Technik

HS-Technik NutBee NBLS-21 Manuale utente

Sumake

Sumake ST-6615 Manuale utente

GOEBEL

GOEBEL Air power Series Manuale utente

ATD AIR

ATD AIR ATD-5850 Manuale utente