GEZE Toplock CTS V Manuale utente

Operating and Installation

Instructions

Code Number Keypad Toplock

CTS V, CTS BV

Keypad with separate evaluating processor unit

CTI, CTI B

With relay which is integrated in the keypad

GEZE GmbH

Reinhold-Vöster-Straße 21-29, 71229 Leonberg

Phone +49 7152-203-0, Fax +49 7152-203-310

Material no. 129510 Number of rev. 00, Drawing no. 21207-9-0963

Subject to change

Description of function

The code number keypads are code switching devices which accept up to 5 different open codes.

Each code activates the same potential-free relay output. Via the keypad,

up to 5 code numbers, each a maximum of 6 digits, are entered with a master code. Once the data has been entered, it

will remain stored, even in the case of a power failure.

Subsequent to entering the valid open code and pressing the key with the bell symbol,

the green LED lights up on the keypad and the relay is activated for approx. 2 seconds.

If the red LED lights up during the code entry an incorrect code has been entered.

The red LED goes out after a few seconds. Only then can a new code be entered. If an incorrect code has been

entered 5 consecutive times, the keypad blocks for one minute.

CTI, CTI B

The device only consists of the keypad.

CTS V, CTS BV

The device consists of 2 parts: The keypad and the decoder. The keypad and the decoder are in sync as a pair with

one key number.

Only keypads and decoders with the same key number can work together.

Programming the Devices

1 Programming a new open code

1.1 Press the key “P”. The red LED starts to blink.

1.2 Enter the valid master code (see also “Master Code Factory Setting”).

1.3 Press the key with the bell symbol. The green LED starts to blink, the red one goes out. (If the red LED is

continuously lit up or continues to blink and the green LED does not blink, the entered master code was

incorrect. Wait until no LED is lit up and try again.)

1.4 Enter the new open code

1.5 Enter the number of the storage location (1 – 5) where you want to store the open code.

1.6 Press the key with the bell symbol. The green LED goes out and the new open code is now saved under the

selected number.

Important!

Since the number of digits of the open code which is saved under storage location no. 1 defines the number of valid

digits of the open codes which are saved under the storage locations no. 2 – 5, it must be entered first.

The number of digits of the open code which is saved under storage location no. 1 must be the same for the other

open codes.

Example: You want to save open code 4711 under the storage location no. 2:

Enter the digit sequence: 4711 2

If an open code which has been saved under a certain storage location is to be made invalid the corresponding

storage location must be overwritten with the new open code.

2 Programming a new master code

2.1 Press the key “P”. The red LED starts to blink.

2.2 Enter the valid master code (see also “Master Code Factory Setting”).

2.3 Press the key with the bell symbol. The green LED starts to blink, the red LED goes out. If the red LED is

continuously lit up or continues to blink and the green LED does not blink the entered master code was

incorrect. Wait until no LED is illuminated and try again.

2.4 Press the key “P”. The red and the green LED blink.

2.5 Enter the new master code

2.6 Press the key with the bell symbol.

The red and the green LEDs go out and the new master code has been saved.

3 Programming the Key Number (only for CTS V, CTS BV) The key number can be found in the

decoder.

3.1 Press the key “P”. The red LED starts to blink.

3.2 Enter the valid master code (see also “Master Code Factory Setting”).

3.3 Press the key with the bell symbol. The green LED starts to blink, the red LED goes out. If the red LED is

continuously lit up or continues to blink and the green LED does not blink the entered master code was

incorrect. Wait until no LED is lit up and try again.

3.4 Press the key “P”. The red and the green LED blink.

3.5 Press the key “P”. The green LED goes out and only the red LED is still blinking.

3.6 Enter the 5-digit key number (zeros which are placed in front must also be entered).

3.7 Press the key with the bell symbol. The red LED goes out and the key number is now saved.

4 Reset to Factory Setting

4.1 Interrupt operating voltage.

4.2.1 Hold a magnet against key 7 of the square keypad or key 2 of the long keypad and reconnect the

operating voltage at the same time. The red LED lights up and the green LED blinks briefly. As a result,

CTS V, CTS BV has been reset to the factory setting.

Important! At the time of switching-on, the magnet must be on the keypad. If the magnet is held against the keypad

when the operating voltage is still on only the red LED lights up, but the keypad is not reset. This way, you can also

find the correct position for the magnet.

CTI, CTI B:

Attention! During reset, all programmed open codes and the master code are cleared. After the reset, the factory

setting applies.

CTS V, CTS BV:

First of all, the key number must be programmed to guarantee the function of the keypad with the decoder. Only

then, the open codes and the master code are to be reprogrammed.

For security reasons, it is very important to change the factory setting again.

Factory setting master code:

11111

Factory setting open code:

1234

4 Pin Assignment:

CTS V, CTS BV

Evaluating processor unit

Keypad

Attention!!!

Disconnect the device from the power for any

installation work

5 Pin Assignment:

CTI CTI B

Relay

Attention!!!

Disconnect the devices from the power for any

installation work.

GEZE GmbH

P.O. Box 1363

71226 Leonberg

Germany

GEZE GmbH

Reinhold-Vöster-Str. 21-29

71229 Leonberg

Germany

Tel. +49 (0)71 52-203-0

Fax+49 (0)71 52-203-310

GEZE Branches

Germany

Asia

Germany

GEZE GmbH

Niederlassung Nord/Ost

Bühringstr.8

13086 Berlin (Weissensee)

Tel. +49(0)30-47 89 90-0

Fax. +49(0)30-47 89 90-17

E-Mail: [email protected]

Poland

Switzerland

Spain / Portugal

Scandinavia

Sweden

Norway

Finland

GEZE Schweiz AG

Bodenackerstr. 79

4657 Dulliken

Tel. +41 (0) 62-285 54 00

Fax. +41 (0) 62-285 54 01

E-Mail: [email protected]

GEZE Iberia S.R.L.

Pol.Ind. El Pla

C/Comerc, 2-22, Nave 12

08980 Sant Feliu de Llobregat

(Barcelona)

Tel. +34 (0) 9 02 19 40 36

Fax. +34 (0) 9 02 19 40 35

E-Mail: [email protected]

GEZE Scandinavia AB

Mallslingan 10

Box 7060

18711 Täby

Tel. +46 (0) 8-732 34-00

Fax. +46 (0) 8-732 34-99

E-Mail: [email protected]

GEZE Finland

Branch office of GEZE Scandinavia AB

Postbox 20

Herralantie 824

15871 Hollola

Tel. +358 (0) 10-400 5100

Fax. +358 (0) 10-400 5120

E-Mail: [email protected]

GEZE Scandinavia AB avd. Norge

Postboks 63

2081 Eidsvoll

Tel. +47 (0) 639 572 00

Fax. +47 (0) 639 571 73

E-Mail: [email protected]

GEZE Polska Sp. z o.o.

Ul. Annopol 21

03-236 Warszawa

Tel. +48 (0) 22 440 44 40

Fax. +48 (0) 22 440 44 00

E-Mail: [email protected]

GEZE GmbH

Niederlassung West

Nordsternstraße 65

45329 Essen

Tel. +49(0)201-830 82-0

Fax. +49(0)201-830 82-20

E-Mail: [email protected]

GEZE GmbH

Niederlassung Mitte

Adenauerallee 2

61440 Oberursel (b. Frankfurt)

Tel. +49(0)61 71-6 36 10-0

Fax. +49(0)61 71-6 36 10-1

E-Mail: [email protected]

GEZE GmbH

Niederlassung Süd

Reinhold-Vöster-Straße 21-29

71229 Leonberg

Tel. +49(0)7152-203-594

Fax. +49(0)7152-203-438

E-Mail: [email protected]

GEZE Sonderkonstruktionen

GmbH

Planken 1

97944 Boxberg-Schweigern

Tel. +49(0)7930-92 94-0

Fax. +49(0)7930-92 94-10

E-Mail: [email protected]

GEZE SERVICE GmbH

Reinhold-Vöster-Str.25

71229 Leonberg

Tel. +49(0)7152-92 33-0

Fax. +49(0)7152-92 33-60

E-Mail: [email protected]

GEZE SERVICE GmbH

Niederlassung Berlin

Bühringstr.8

13086 Berlin (Weissensee)

Tel. +49(0)30-47 02 17-30

Fax. +49(0)30-47 02 17-33

GEZE Representative:

Id. No. 129510 Modification level 00 Drawing No. 21207 0963 • • Subject to change without notice•. -9- Printed in Germany

Yourattentionisdrawntothe

“productliabilitylaw“definedliabilityto

themanu-facturerforhisproducts

whicharecon-tainedinthemain

catalogue(productinformation,usage,

misuses,productactivity,product

maintenance,thedutytoinformandthe

dutytoinstruct).Noncompliancewith

theseconditionsre-lievesthe

manufacturerfromanyliability.

Subsidiaries

GEZE Online:

www.geze.com

DIN ISO 9001

The

hallmark

of our

enterprise

Europe

France

Great Britain

Italy

Benelux

Middle East

GEZE France S.A.R.L

ZAC de l’Orme Rond

RN 19

77170 Servon

Tel. +33 (0) 1 60 62 60 70

Fax (0).+33 1 60 62 60 71

E-Mail: [email protected]

Austria

GEZE Austria GmbH

Mayrwiesstraße 12

5300 Hallwang b. Salzburg

Tel. +43 (0) 662 66 31 42

Fax. +43 (0) 662 66 31 42-15

E-Mail: [email protected]

GEZE Italia Srl

Via Giotto 4

20040 Cambiago (MI)

Tel. +39 (0) 02 95 06 95-11

Fax. +39 (0) 02 95 06 95-33

E-Mail: [email protected]

GEZE Engineering Roma Srl

Via Lucrezia Romana 91

00178 Roma

Tel. +39 (0) 06 72 65 31 1

Fax. +39 (0) 06 72 65 31 36

E-Mail: [email protected]

GEZE Benelux B.V.

Industrieterrein Kapelbeemd

Leemkuil 1

5626 EA Eindhoven

Tel. +31 (0) 40 26 29 08 0

Fax. +31 (0) 40 26 29 08 5

E-Mail: [email protected]

U.A.E.

GEZE Middle East

P.O. Box 17903

Jebel Ali Free Zone

Dubai

Tel. +971 (0) 4 88 33 112

Fax. +971 (0) 4 88 33 240

E-Mail: [email protected]

GEZE UK Ltd.

Blenheim Way

Fradley Park

Lichfield

Staffordshire WS13 8SY

Tel. +44 (0) 15 43 44 30 00

Fax. +44 (0) 15 43-44 30 01

E-Mail: [email protected]

Denmark

GEZE Denmark

Branch office of GEZE Scandinavia AB

Høje Taastrup Boulevard 53

DK - 2630 Taastrup

Tel. +45 46-32 33 24

Fax. +45 46-32 33 26

E-Mail: [email protected]

GEZE Industries

(Tianjin) Co., Ltd.

Shuangchenzhong Road

Beichen Economic Development

Area (BEDA)

Tianjin 300400, P.R. China

Tel. +86 (0) 22-26 97 39 95-0

Fax. +86 (0) 22-26 97 27 02

E-Mail: [email protected]

GEZE Industries

(Tianjin) Co., Ltd.

Branch Office Shanghai

Room 3010

Tower 2, Grand Gateway

No. 3 HongQiao Road, XuHui District

200030 Shanghai, P.R. China

Tel. +86 (0) 21 64475908

Fax. +86 (0) 21 64472007

E-Mail: [email protected]

GEZE Industries

(Tianjin) Co., Ltd.

Branch Office Beijing

No. 6-32 Building

Jili Avenue

Daxing District

100076 Beijing, P.R. China

Tel. +86 (0) 10 87965152

Fax

Tel. +86 (0) 10 87975178

. +86 (0) 10 87971476

E-Mail: [email protected]

South Africa

DCLSA Distributors (Pty) Ltd.

1027 Richards Drive, Midrand

P.O. Box 7934, Midrand 1685

South Africa

Tel. ++27 11 3158286

Fax. ++27 11 31558261

E-Mail: [email protected]

GEZE Industries

(Tianjin) Co., Ltd.

Branch Office Guangzhou

Room 17C3 Everbright Bank Building,

No.689,

Tian He Bei Road

510630 P.R. China

Tel. +86 20

Guangzhou,

(0) 3873842

Fax. +86 (0) 20 38731834

E-Mail: [email protected]

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali GEZE Interruttore

GEZE

GEZE KFT 114078 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente