Gigabyte SkyVision WS100 Manuale utente
SkyVision WS100
User’s Manual
Copyright
© 2012 GIGABYTE TECHNOLOGY CO., LTD
Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. (“GBT”). No part of this manual may be
reproduced or transmitted
in any form without the expressed, written permission of GBT.
Trademarks
Third-party brands and names are the properties of their respective owners.
Notice
Please do not remove any labels on this product. Doing so may void the warranty of this
product. Due to rapid change in technology, some of the speci cations might be out of date
before publication of this manual. The author assumes no responsibility for any errors or
omissions that may appear in this document nor does.The author make a commitment to
update the information contained herein.
Rovi Product Notice:
This product incorporates copyright protection technology that is protected by U.S. patents
and other intellectual property rights. Use of this copyright protection technology must be
authorized by Rovi Corporation, and is intended for home and other limited viewing uses only
unless otherwise authorized by Rovi Corporation. Reverse engineering or disassembly is
prohibited.
English
-2-
Supported Resolution
Please make sure the source device is compliant with the following
standards. If the source device does not support the following frame rate,
the OSD will show that no video displayed or the video quality is poor.
640x480p @ 59.94 / 60 Hz
480p
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
720x480p @ 59.94 Hz
576p
720x480p @ 60 Hz
720p
720x576p @ 50 Hz
1280x720p @ 50 Hz
1280x720p @ 59.94 / 60 Hz
1920x1080i @ 50 Hz
1920x1080i @ 59.94 / 60 Hz
1920x1080p @ 50 Hz
1920x1080p @ 59.94 / 60 Hz
1920x1080p @ 29.97 / 30 Hz
640x480 @ 59.94 / 72.809 Hz
800x600 @ 60.317 / 72.188 Hz
1024x768 @ 60 / 70.069 Hz
1280x768 @ 60 Hz
1280x1024 @ 60 Hz
1366x768
1920x1080
Video Forate Timing Resolution Supported
1080i
1080p / 60
1080p / 24
VGA
SVGA
XGA
WXGA
SXGA
English
-3-
SkyVision WS100 Specication
Featuring WHDI (Wireless Home Digital Interface) technology,
GIGA-BYTE SkyVision WS100 can seamlessly transmit 1080p high-
definition videos or Blu-ray movies from any HDMI-ready device to
HDTV or display. It can transmit uncompressed video contents up to 10
meters (Line of sight) with no latency (latency < 1ms).
Wireless Technology WHDI 1.0
Host Interface HDMI (Type A)
Video quality Uncompressed
Video resolution
Audio
Operating frequency
Range
Latency
Power supply
I/O port
Dimensions
SkyVision WS100
HD: 480p,576p,720p,1080i, 1080p/60Hz
PC: VGA (640x480), SVGA (800x600),
XGA (1024x768), SXGA (1280x1024)
Panel: 1280x768, 1366x768, 1920x1080
Up to 18Mbps audio stream
5.1 channel, up to 48KHz 24 Bit, AC3 and DTS
USA/CANADA:
5170-5250 (MHz), 5735-5815 (MHz)
EUROPE/ RUSSIA:
5170-5210 (MHz), 5210-5250 (MHz)
Taiwan: 5745-5805 (MHz)
Up to 10 meters (Line of sight)*
(transmission quality varies with the environment)
< 1ms
TX: 5V micro USB cable(female)
RX: 5V, 2A micro USB power cable
TX: HDMI port*1, Micro USB*1
RX: HDMI port*1, DC-In*1
TX: 93x32x15.3 mm (LxWxH)
RX: 93x82x32 mm (LxWxH)
English
-4-
Packing Content
Before setting up, please check whether the following items are in the
package. If any item is missed or damaged, please contact your retailer.
English
-5-
Overview
1. Before You Begin
SkyVision WS100 transmitter (GT-WS100TX);
SkyVision WS100 receiver (GT-WS100RX);
HDMI connector: Connects to the HDMI port of the source device
Micro USB power connector: Connects to the USB port of the source
device with bundled USB cable.
Registration button: Registration button is reserved for receiver paring use.
LED indicator:
On: LED indicator is solid blue
Linking to SkyVision WS100 receiver: LED indicator is blinking
HDMI port: Connects to HDMI-ready TV or display with bundled HDMI cable
Micro USB power port: Connects to external power with bundled power adapter
Menu button: Setup menu
Up button: Scrolls up through the menu
Down button: Scrolls down through the menu
Power LED indicator:
Power on: LED indicator is solid white
Power off: LED indicator is off
Link LED indicator:
Linked: LED indicator is solid blue
Linking to SkyVision WS100 transmitter: LED indicator is blinking
1
1
2
2
3
3
4
4
5
6
7
English
-6-
Note:
1. When SkyVision WS100 is functioning normally, power LED indicator
will be in solid white and link LED indicator will be in solid blue. Please
refer to the following table for LED behavior.
Standby
Initial boot up
Searching channels
Wireless linked
In power saving mode Solid white off
Blinking blue
Blinking blue
Solid blue
Solid blue
Solid blue
Solid white
Solid white
Solid white
Solid white
Solid white
Boot up needs
15 to 20 seconds
Searching for
available channels
No input from
selected source
Video format
not recognized
Video format
is recognized
Mode Status description Power LED Link LED
English
-7-
2.3 Rename SkyVision WS100
1. Press Menu button
2. Press Up or Down button to select Settings
3. Select Rename Video Source
4. Press Menu button to select the video source to be renamed
5. Use Up and Down buttons to move horizontally and highlight the
character to be changed
6. Press Menu button to select the character to be renamed
7. Press Up or Down button to change the character
8. Press Menu button to conrm selected new character
9. Press and hold Menu button to Apply or Cancel Rename Video
Source section
2. On Screen Display (OSD) Instruction:
The Menu button on SkyVision WS100 receiver allows you to add,
remove, or rename SkyVision WS100 transmitter. You can also
disconnect SkyVision here.
2.1 To add another SkyVision WS100 transmitter or remove existing
SkyVision WS100 transmitter
1. Press Menu button
2. Press Up or Down button to select Settings
3. Press Up or Down button to select Add New Video Source or Remove
Video Source
4. Press Menu button to select video source you want to add or remove
5. Select OK to apply the change
2.2 Disconnect SkyVision WS100
1. Press Menu button
2. Press Up or Down button to select Settings
3. Select Disconnect SkyVision
4. Select OK to apply the change
English
-8-
Installation
SkyVision WS100 can wirelessly transmit high-definition video/audio
contents from devices such as PC, laptop, Blu-ray player, set-top box,
PS3, and Xbox to TV or display*.
* Both source and display device must have HDMI ports
Step 1.
Setup SkyVision WS100 Transmitter
Connect the bundled USB cable to SkyVision WS100 and then connect
SkyVision WS100 and USB cable to the source device. Please plug SkyVision
to source device’s HDMI port and plug USB cable to source device’s USB
port. SkyVision WS100 transmitter’s power is supplied from the USB port of
the source device.
Step 2.
Setup SkyVision WS100 Receiver
Connect the bundled power adapter to SkyVision WS100 and insert the power
adapter into a power outlet then connect SkyVision WS100 to the external display
through bundled HDMI cable.
Note:
1. Please make sure your display is in “HDMI” input mode. When the components
are connected correctly and the correct source is selected, the image on the
source device will be showed on the display.
2. It may take a few seconds for SkyVision WS100 to link each other and for the
image on the source device to the display. During the linking period, link LED
indicators on the transmitter and receiver will blink in blue. When linking, link
LED indicators will be solid blue.
to source device’s HDMI port and plug USB cable to source device’s USB
port. SkyVision WS100 transmitter’s power is supplied from the USB port of
the source device.
1
1
2
2
3
3
English
-9-
Display Setting
Adjust Screen Resolution
SkyVision WS100 supports duplicate mode, extend mode, and projector
only mode on external display. Please follow the steps below to enable
external display.
SkyVision WS100 supports 1080p full HD video resolution without
latency (latency < 1ms). You can manually adjust preferred resolution by
the following steps.
1. Windows Utility
Step1. Press and tap P
Step2. Select Clone mode, Extend display, or Project out only
2. MAC OS
Step1. Click System Performance to open Displays
Step2. Click Detect Display to detect external display
1. Windows Utility
Adjust screen resolutions on both source device and external display
Note:
MAC OS will automatically detect external display and switch to a better resolution
when external display cable is plugged in.
Step1. Right click the mouse on Windows desktop
and choose Screen resolution
Step2. Dropdown the Resolution list and select
preferred resolution
Step3. Click Apply
Step4. Click Keep Change when con rmation
message pop out
Step5. Click OK
Step1. Press and tap P
English
-10-
Adjust screen resolutions on source device or external display
Adjust Audio Setting
Step1. Right click the mouse on Windows desktop and choose Screen resolution
Step2. Dropdown the Resolution list and select preferred resolution for the
speci c display
Step3. Click Apply
Step4. Click Keep Change when con rmation message pop out
Step5. For generic PnP monitor and Intel Graphic Media accelerator HD screen,
click monitor and select 60Hz as the screen refresh rate
Step6. Click OK
Step1. Please open Audio Setting form control panel
Step2. Select HDMI output and click OK
Questo manuale è adatto per i seguenti modelli
2
Indice
