Gigabyte SW016A Manuale utente
User’s Manual
For
16/24-port 10/100Mbps
Auto-Negotiation Smart Switches
(Version 1.5)
FCC Class A Compliance
This equipment generates and uses radio frequency energy. If it
is not installed and used properly in strict accordance with the
manufacturer’s instructions, it may cause interference to radio
and television reception. It has been type-tested and found to
comply the specifications in sub- part J of Part 15 of FCC Rules,
which are designed to provide reasonable protection against
such interference in a residential installation. There is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio
or television reception which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the Interference by one or more of the following measures:
Re-orient the receiving antenna
●Relocate the computing device with respect to the receiver
●Move the computer away from the deceiver
●Plug the computer into a different outlet so that compute and
receiver are on different electrical circuits.
If necessary the user should consult the dealer or
an experienced radio or television technician for additional
suggestions.
The information in this manual is subject to change without
notice. All the brand names are registered trademarks of their
Checklist:
Check the contents of your package for following parts:
16/24-port 10/100M Fast Ethernet Smart Switch
Power Cord and Accessory
User’s Manual
Console Port Cable (option)
If any of these pieces are missing or damaged, please contact your
dealer immediately, If possible, retain the carton including the
original packing material, and use them against to repack the
product in case there is a need to return it to us for repair.
Contents PAGE
Introduction------------------------------------------1
Features and Specifications-------------------------2
Hardware Description------------------------------- 4
FrontPanel
RearPanel
Hardware Installation---------------------------------6
Configuration------------------------------------------7
10/100M bps(Server)Switching
10/100M bps(Hub)Switching
Switch Operation--------------------------------------8
AddressTable
Learning
Forwarding & Filtering
Store-and-Forward
Auto-Negotiation
Hardware Troubleshooting
Introduction
The 16/24-port Ethernet Switches are designed to allow
simultaneous transmission of multiple packets via an
internal high-speed data channel. This means that it can
partition a network more efficiently than bridges or routers
in most environments. This 16/24-port Ethernet switching
is a highly reliable network switch and is the ideal device
for bridging Ethernet to Fast Ethernet workgroups or
networks. Simple and cost-effective, the 16/24-port
Ethernet Switching supports IEEE802.3u, IEEE802.3,
100Base-TX. And 10Base-T. the 16/24-port Ethernet
Switching is therefore fast being recognized as one of the
most important building blocks for today networking
technology.
The front panel of the 16/24-port Ethernet Switches
provide LEDs for easy recognition of the operation status
and troubleshooting. These LEDs indicate the status of
system power and per port link, including link, speed,
collision, full/half-duplex, and receive status.
The 16/24-port Ethernet Switches are specially designed
for connecting workgroup devices and desktops, with low
cost and flexibility for backbone implementations. Instead,
companies can deploy scaleable, affordable switches that
increase the aggregate bandwidth of the network by
boosting throughput to the workgroups that need it most.
Features and Specifications
Features:
16/24-port 10/100mbps TX Auto-Negotiation
Ethernet Switch
Complies with the IEEE802.3 Ethernet and
IEEE802.3u Fast Ethernet standard
Features Store-and-Forward mode with wire-speed
filtering and forwarding rates
Full/Half-Duplex capability on every TX ports, total
bandwidth is up to 200Mbps port
Automatic source address learning and aging
Support up to total 8k/8k MAC address
Support up to 4M/2.5M bit buffers with dynamic
allocation
IEEE802.3x compliant flow control for full duplex
Half-duplex flow control
Internal power supply
Plug and play
Port Trunking support. Four trunk groups are provided
each consisting of 4 physical ports. Trunk load
balance is controlled by DA/SA hash algorithm.
Trunk port LEDs supported. (16 Port only)
Support Auto MDI/MDI-X Function.
Port based HOME VLAN function 16/24-Port
(option).
Specifications:
Comply IEEE802.3/IEEE802.3u/IEEE802.3x
Network Media
100Base-TX-UTP/STP category 5 cable
10Base-T-UTP/STP category 3 or 5 cable
Connector: STP RJ-45port for 10/100Mbps TX
LED indicators:
Power (per unit)
Link/Activity, Speed, and Duplex/Collision (per port)
Dimension:
16-Port Rack-mountable
440mm(L) ×200mm(W) ×45mm(H)
16-Port Desktop
300mm(L) ×116mm(W) ×45mm(H)
24-Port Rack-mountable
440mm(L) ×200mm(W) ×45mm(H)
Temperature: Operating: 0
℃
to 40
℃
Storage: -20
℃
to 70
℃
Humidity: Operating: 10%to 90% RH
Storage: 5% to 90% RH
Input Power Requirement: 90-240VAC, 50-60Hz,
Auto-sensing
Registrations: FCC Part 15 Class A, CE
Hardware Description
This section describes the hardware features of the
16/24-port Ethernet Switching. For Easier management
and control of the switch, familiarize yourself wide its
display indicators, and ports, Front panel illustrations in
this chapter display the unit LED indicators. Before
connecting any network device to the hub, read this
chapter carefully.
Front Panel
The unit front panel provides a simple interface
monitoring the switching hub. It includes a power
indicator for each port.
16-Port Rack-Mountable
24-Port Rack-Mountable
16-Port Desktop
LED indicators
LED Function Color Description
PWR Green ON: Power on
LINK/ACT Green ON: Indicates the adapter is connected
to hub
Flash: Indicates data in or out the port
10/100 Green ON: 100Mbps
OFF: 10Mbps
Module Green
ON: 100Base-FX module installed (24s
only)
FDX/COL Green ON: Full Duplex
OFF: Half Duplex
Blink: collision
Trunk 1
Group (16-Port Only)
Green ON: Trunk Group is 1x, 2x, 5x, 6x
OFF: Trunk disable
Trunk 2
Group (16-Port Only)
Green ON: Trunk Group is 3x, 4x, 7x, 8x
OFF: Trunk disable
Trunk 3
Group (16-Port Only)
Green ON: Trunk Group is 9x, 10x, 13x, 14x
OFF: Trunk disable
Trunk 4
Group (16-Port Only)
Green ON: Trunk Group is 11x, 12x, 15x, 16x
OFF: Trunk disable
Rear Panel
The rear panel of the 16/24-port Ethernet Switching hub indicates
a AC inlet, which accepts 100-240VAC 50-60Hz power input
and one module option.
On 24-Port switch, the fiber optic module is designed to share
with the 24th TP port, do not simultaneously use 24th TP port
and fiber optic module. And 16th TP port is shared with the
optic module on 16-port switch.
Console port is optional on 16-port switch
16-Port Rack-Mountable
24-Port Rack-Mountable
16-Port Desktop
Indice
Altri manuali Gigabyte Interruttore
