gio Titan PRemium Manuale utente
PLEASE INSPECT YOUR GIO ELECTRIC TITAN PREMIUM MOBILITY
SCOOTER UPON ARRIVAL AND REPORT ANY DAMAGES THAT MAY
HAVE OCCURRED DURING SHIPPING
⚠SAFETY INFORMATION ⚠
Please note the following information to ensure your safety and get better
use out of your GIO Titan Premium (Titan PR for short) Long Range Mobility
Scooter
Please read the manual prior to first use and do not permit anyone who
hasn’t, operate the vehicle.
This scooter is designed only for one adult only. Never exceed the max load
capacity of the vehicle. 440lbs (200kg)
Take extra care when handling the batteries inside your scooter. Avoid
directly touching contacts with damp hands or metal tools to prevent
electrocution.
To ensure the safety and reliability of your scooter, do not modify your
scooter, and always use parts, i.e. charger, specifically designed for the GIO
Titan PR.
⚠ALWAYS APPLY BRAKES WHILE GOING DOWNHILL TO CONTROL
SPEED AND AVOID SHARP TURNS AT HIGHER SPEEDS TO
PREVENT TIPPING SIDEWAYS! ⚠
⚠THIS VEHICLE WAS NOT MANUFACTURED PRIMARILY FOR USE ON
THE PUBLIC ROADS AND THUS IS NOT A MOTOR VEHICLE SUBJECT TO
THE FEDERAL MOTOR VEHICLE SAFETY, BUMPER AND THEFT
PREVENTION STANDARDS OR THE EQUIPMENT ITEM IS NOT A SYSTEM,
PART, OR COMPONENT OF A MOTOR VEHICLE AND THUS IS NOT AN
ITEM OF MOTOR VEHICLE EQUIPMENT SUBJECT TO THE FEDERAL
MOTOR VEHICLE SAFETY STANDARDS. [591.5(A)] ⚠
01
Table of Contents
Riding Safety 2
Overview 3
Scooter Assembly 3
Scooter & Control Diagrams 7
Operating & Adjusting Your Scooter 9
Maintenance & Care 13
Specifications & Troubleshooting 16
Warranty Information 18
Riding Safety
ALWAYS wear an approved helmet when riding your scooter
ALWAYS steer with both hands
ALWAYS drive with caution at appropriate speeds
ALWAYS use your scooters turn signals and horn
ALWAYS obey local traffic laws
ALWAYS be aware of your surroundings, pedestrians, traffic, etc
ALWAYS take extra care when driving in spaces shared with motor vehicles,
parking lots, driveways, crosswalks etc
ALWAYS apply brakes while driving downhill to regulate speed
ALWAYS take extra care driving in wet conditions
ALWAYS allow extra room for braking in wet conditions
ALWAYS wear reflective clothing while driving in darker conditions
ALWAYS use your lights when driving in darker conditions
AVOID driving while fatigued or tired
AVOID driving under the influence of drugs or alcohol
AVOID distracted driving by not using a cell phone while driving
AVOID driving off-road or on surfaces that may lead to scooter damage
AVOID driving in conditions that may get the electric components wet
AVOID driving in conditions where you are not visible
02
Overview
Thank you for your purchase of the GIO Electric Titan PR Long Range
Mobility Scooter. It is an easy to operate mobility scooter designed for
indoor and outdoor use. This stylish recreational mobility scooter doesn’t
require any licensing, registration or insurance. (unless required locally)
Inspired by motorcycle design, the original Titan PR is packed with features
from alarm system to generous top speeds, long driving range, front and
rear suspension, and hydraulic brakes. This manual contains a wide range
of general information and should be read before you operate it. Please
note final details and/or images may vary from final product.
Assembly
Your Titan PR arrives 98% assembled and is ready in 5 simple steps.
Step 1 - Unboxing
Untie or snip the wires holding your Titan PR in its protective frame and
remove it from its packaging. Ensure the following components are
included:
Rear Basket & Hardware Mirrors (1ea Left & Right)
Keys & Fobs Smart Charger
03
Riding Poncho Security Lock
Windshield Kit (Optional Installation)
Step 2 - Installing the Basket
First attach the top to the basket body with the provided hardware. Once
attached, locate the premade holes located in the back side of the seat and
mount the basket as a whole.
04
Step 3 - Installing the mirrors
Insert the mirrors into the mounting points above the controls and tighten
into place. (If adding the optional windshield, install in step 6 instead)
Step 4 - Turning on the breaker
Your scooter ships with the breaker in the off position. Open the underseat
compartment to find the breaker inset in the compartment liner next to the
latch. Flip the breaker to the on position. The scooter will not charge or
operate unless the breaker is in the on position.
05
Step 5 - Charging
Charge your battery for the first time - Your scooter does not arrive fully
charged and will need charging before it is ready to drive. See instructions
for charging on page #.
Step 6 - (Optional Installation) Windshield
The Titan PR includes the previously separate windshield kit at no extra
cost. The windshield is not required for use and is completely optional to
install. Ensure hands are clean and take care with plastic components to
avoid damaging the windshield during installation.
Locate the hardware for the brackets that mount to the acrylic shield panel.
Each side consists of an outer bracket, rubber grommet, rubber washers
(x2), nuts (smaller size x2), an L shaped support and 2 plastic mounting
clips. Begin by sliding 2 mounting clips onto the longer portion of the
support, facing the opposite to the short side of the support.
Next layer the rubber grommet over the threads of the outer bracket and
insert through the premade holes in the acrylic shield. Align the mounting
clips on the L shaped support with the outer bracket threads. (Short side of
the support pointing towards the edge of the shield. Add rubber washers to
the threads before securing each with a nut. Repeat the process for the
other side to complete the windshield body. (See images on next page…)
06
You can now begin mounting it to the scooter. Locate the 2 metal mounting
clips. Remove each mirror, place the mounting clip over top of the hole the
mirror slots into, extending the clip towards the driver. Reinsert each mirror
through the mounting clip into its mounting hole and loosely tighten for now.
Thread one of the larger nuts all the way along each of the threaded shorter
portions of the L shaped supports.
07
Next slide one of those threaded supports into the receiving channel on the
metal mounting clips you just installed. Carefully flex the windshield to allow
the other threaded support to be guided into the metal mounting clip on the
opposite side.
With the windshield now in place add the 2 remaining nuts to the ends of the
threaded part of the support. Using 2 wrenches tighten the nuts towards the
mounting clip to secure in place. Repeat on the other side, tighten the
mirrors to complete installation
08
Scooter Diagram
1
Mirrors
10
Armrests (flip up)
2
Headlight
11
Seat adjustment levers
3
Front turn signal lights
12
Basket
4
Front wheel & fender
13
Underseat compartment
5
Front fork & brakes
14
Battery & Controller (internal)
6
Handlebar, controls, display
15
Rear turn signal lights
7
Ignition
16
Rear brakes & wheels
8
Covered charging port
17
Motor (internal)
9
Seat & headrest
18
Tip protection wheels
09
Altri manuali gio Scooter
