Gira 2120 00 Manuale utente
Power supply 160 mA, 320 mA, 640 mA, 1280 mA with integrated choke
Power supply 160 mA with integrated choke
Order no.: 2120 00
Power supply 320 mA with integrated choke
Order no.: 2122 00
Power supply 640 mA with integrated choke
Order no.: 2130 00
Power supply 1280 mA with integrated choke
Order no.: 2138 00
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. During installation and cable routing, comply with the regulations and
standards which apply for SELV circuits.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
Figure1: View
1 / 8
82597322 06.05.2019
Power supply 160 mA, 320 mA, 640 mA, 1280 mA with integrated choke
Figure2: 1280 mA power supply – view
(1) Connection of mains
(2) LED Betrieb, green
On: Normal operation
Flashes: Overload or overvoltage
Off: No mains voltage or internal error
(3) LED Überlast, red
On: Overload or short-circuit on KNX bus line or output DC 30 V
(4) LED Überspannung, yellow
On: Overvoltage on KNX bus line or output DC 30 V
(5) Output DC 30 V
(6) Output Bus for KNX bus line
(7) LED Reset, red
Flashes rapidly 2.5 Hz: Reset for 20 seconds
Flashes slowly 0.25 Hz: Permanent reset
(8) Button Reset
Acknowledge the diagnostic message: Press briefly, < 0.5 seconds
Switch off the KNX bus line for 20 seconds: Press between 2...4 seconds
Permanently switch off the KNX bus line: Press longer than 4 seconds
Terminate the permanent reset: Press the button
(9) Signal contact for diagnostic message
Closed: Normal operation
Open: After overload, overvoltage or in case of a power failure
3 Function
System information
This device is a product of the KNX system and complies with the KNX directives. Detailed tech-
nical knowledge obtained in KNX training courses is a prerequisite to proper understanding.
Intended use
– Supplying KNX devices with bus voltage
– Supplying devices with direct current
– Mounting on DIN rail according to EN 60715 in sub-distribution unit
Product characteristics
– Output with integrated inductance for supplying KNX bus lines
– DC 30 V output for supplying additional devices
2 / 8
82597322 06.05.2019
Power supply 160 mA, 320 mA, 640 mA, 1280 mA with integrated choke
– Nominal current can be subdivided to outputs as desired
– Reset button
– Short-circuit proof
– Overvoltage proof
– No-load proof
– Suitable for operation in systems with emergency power supply
– Potential-free signal contact for operating and diagnostic message
– Two identical power supplies can be connected in parallel (with the versions 160 mA, 320
mA and 640 mA)
4 Operation
Acknowledging the diagnostic message
After detecting a overvoltage or a short circuit the LED and the signal contact signal the event
until the message is acknowledged.
￭ Press the Reset button for less than 0.5 seconds.
LED functions and signal contact
LED
Betrieb (2),
green
LED
Überlast (3),
red
LED
Überspan-
nung (4), yel-
low
LED
Reset (7), red
Signal contact
(9)
Normal opera-
tion
on off off off closed
Reset for
20 seconds
on off off flashes 2.5 Hz closed
Permanent re-
set
on off off flashes
0.25 Hz
closed
Overvoltage flashes 0.5 Hz off on (until the
message is
acknow-
ledged)
off open (until the
message is
acknow-
ledged)
Overload,
short-circuit
flashes 0.5 Hz on (until the
message is
acknow-
ledged)
off off open (until the
message is
acknow-
ledged)
Voltage
failed / internal
error
off off off off open
In normal operation the control of the power supply is not necessary. The button (8) is recessed
and thus prevents that it is inadvertently actuated in operation.
Reset function and Reset button
When resetting a bus segment, the output voltage of the power supply is switched off. At the
same time the bus line is short-circuited so that all connected bus devices are disconnected
from the bus voltage.
Resetting the bus line for 20 seconds
￭ Press the Reset button (8) between 2 ... 4 seconds.
The bus line is short-circuited for 20 seconds.
The LED Reset (7) flashes quickly.
After 20 seconds the bus voltage is switched on again and the LED Reset switches off.
3 / 8
82597322 06.05.2019
Power supply 160 mA, 320 mA, 640 mA, 1280 mA with integrated choke
Permanently resetting the bus line
￭ Press the Reset button (8) for more than 4 seconds.
The bus line is short-circuited.
The LED Reset (7) flashes slowly.
Terminating the permanent reset
Prerequisite: The bus line is permanently reset, the LED Reset (7) flashes slowly.
￭ Press the Reset button (8).
The bus voltage is switched on again and the LED Reset switches off.
5 Information for electrically skilled persons
DANGER!
Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live parts
in the working environment.
Fitting the device
Observe the temperature range. Ensure sufficient cooling.
￭ Mount the device on DIN rail. The terminals for the mains connection (1) must be at the
top.
4 / 8
82597322 06.05.2019
Power supply 160 mA, 320 mA, 640 mA, 1280 mA with integrated choke
Connecting the device to mains voltage and bus
Figure3: Wiring example – mains voltage and bus line
Figure4: Clampable conductor cross-section
￭ Connect the mains voltage to the terminals L and N (1).
￭ Connect the protective conductor PE to the terminal Ʈ.
￭ Connect the KNX bus line to output Bus (6).
￭ Install the cover to protect the bus connection against hazardous voltages in the connec-
tion area.
The total load of the outputs can be subdivided as desired. Do not exceed the total rated
current.
Do not connect any other products to the bus output. This might influence the bus com-
munication.
If required, an identical power supply can be connected in parallel for the device variants
160, 320 and 640 mA.
Connecting the diagnostic analyser
The power supply signals mains failure, overvoltage, overload and short circuit using a poten-
tial-free contact (9). A monitoring device can detect the switching status and forward it for dia-
gnostic purposes.
5 / 8
82597322 06.05.2019
Power supply 160 mA, 320 mA, 640 mA, 1280 mA with integrated choke
The signal output serves only for signalling purposes and may not be used as a load out-
put.
A signal lamp, a signal relay or, e.g., a KNX binary input connected to a KNX bus line can be
used as monitoring device.
￭ Connect the signalling device according to the connection example (Figure 5).
L N
L
N
PE
max. 2 A
Figure5: Application example – signal lamp for optical operating display
￭ Connect the KNX binary input according to the connection example (Figure 6).
Figure6: Application example – KNX binary input on main line for detecting and centrally sig-
nalling diagnostic messages
Observe the wiring! Install the cables for the signal contact such that no loops are cre-
ated. During operation loops can cause interference voltages to be coupled into.
6 / 8
82597322 06.05.2019
Power supply 160 mA, 320 mA, 640 mA, 1280 mA with integrated choke
Operation with emergency power systems
The power supply can be used in combination with centrally supplied emergency power sys-
tems. In this way, the function of the KNX system and the control of the most important func-
tions can be ensured in emergency operation.
Statutory and standard specifications for emergency power and emergency lighting sys-
tems vary from country to country. In any event, the user / technical planner must check
whether the specific specifications are observed.
Cable lengths
For KNX line segments and power supplies the following rules apply:
– Bus line length per lin segment: Max. 1000 m
– Bus line length between power supply and KNX bus subscriber: Max. 350 m
– Bus line length between two KNX bus subscribers: Max. 700 m
6 Technical data
Rated voltage AC 220 ... 240 V~
The device is operable in the range of 180 V
AC … 264 V AC.
Mains frequency 50 / 60 Hz
Power loss (max. load on all outputs)
Art. no. 2120 00 max. 1.5 W
Art. no. 2122 00 max. 1.8 W
Art. no. 2130 00 max. 2.9 W
Art. no. 2138 00 max. 6.4 W
Efficiency
Art. no. 2120 00 approx. 76%
Art. no. 2122 00 approx. 84%
Art. no. 2130 00 approx. 87%
Art. no. 2138 00 approx. 86%
Rated voltage DC DC 240...250 V
KNX
KNX medium TP256
Bus output voltage DC 28 ... 31 V SELV
Output current
Art. no. 2120 00 160 mA (all outputs)
Art. no. 2122 00 320 mA (all outputs)
Art. no. 2130 00 640 mA (all outputs)
Art. no. 2138 00 1280 mA (all outputs)
Short-circuit current
Art. no. 2120 00 max. 1 A
Art. no. 2122 00 max. 1 A
Art. no. 2130 00 max. 1.5 A
Art. no. 2138 00 max. 3 A
Connection type for bus device connection terminal
Parallel operation with identical power supply
Art. no. 2120 00 Yes
Art. no. 2122 00 Yes
7 / 8
82597322 06.05.2019
Power supply 160 mA, 320 mA, 640 mA, 1280 mA with integrated choke
Art. no. 2130 00 Yes
Art. no. 2138 00 No
Output DC 30 V
Output voltage DC 30 V
Signal output
Switching voltage AC AC 12 ... 230 V~
Switching voltage DC DC 2 ... 30 V
Switching current 5 mA ... 2 A
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Relative humidity max. 93 % (no condensation)
Fitting width
Art. no. 2120 00 72 mm / 4 module
Art. no. 2122 00 72 mm / 4 module
Art. no. 2130 00 72 mm / 4 module
Art. no. 2138 00 108 mm / 6 module
Connection mode device connection terminal
Finely stranded with conductor sleeve 0.5 ... 2.5 mm²
7 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
Please submit or send faulty devices postage paid together with an error description to your re-
sponsible salesperson (specialist trade/installation company/electrical specialist trade). They will
forward the devices to the Gira Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel +49(0)21 95 - 602-0
Fax +49(0)21 95 - 602-191
www.gira.de
8 / 8
82597322 06.05.2019
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Gira Alimentazione elettrica
