gofanco HDExt24-HD20 Manuale utente
2x4 HDMI 2.0 Splitter/Extender
User's Guide
G4-0112A
P/N:HDExt24-HD20
2
Thank you for purchasing from gofanco. Our products
aim to meet all your connectivity needs wherever you
go. For optimum performance and safety, please read
the instructions carefully and keep this User's Guide for
future reference. If you need more information about
our products, please visit www.gofanco.com. For
For drivers or manual download, please go to
www.gofanco.com/downloads.
Important Safety Notices
Pleasereadsafetyinstructionscarefullybeforeinstallation
and operation.
• Please pay close attention to all warnings and hints
for this device
• Do not expose this unit to rain, heavy moisture, or
liquid
• Do not put any items into the device or attempt to
modify its operation
• Do not repair the device or open the enclosure
without professional guidance to avoid electric
shocks. Doing so may void your warranty
• Keep the product in a well-ventilated location to
avoid damage from overheating
• Shut off power and make sure environment is safe
before installation
• Do not plug the HDMI cables and IR cables
in/out when the device is in use to avoid cable
damage. Make sure they are plugged into the
correct ports
• Use the included power adapter only. Make sure
the specification matches if using 3rd-party DC
power adapters
3
Introduction
The 2x4 HDMI 2.0 Splitter/Extender distributes HDMI
signals from one of two source devices to 4 CAT6/7
outputs and one HDMI output (loopout).
Features
• Distributes HDMI signals from one of two inputs to
4 CAT6/7 outputs and one HDMI output (loopout)
• CAT6/7 outputs: Up to 80m (262ft) at 1080p and
70m (230ft) at 4K
• HDMI 2.0 and HDCP 2.2 compliant. 18Gbps
bandwidth and supports up to 4K@60Hz YUV 4:4:4
• Supports bi-directional IR control, PoC,
comprehensive EDID management, cascade
connection, and 4K to 1080p downscaling
• Supports auto-switching based on 5V or TMDS
detection
• Controllable by front panel buttons, IR, and RS232
Installation Requirements
• HDMI source devices (DVD player, set top box, PC,
etc.)
• HDMI displays (SDTV/Monitor, HDTV/Monitor,
projector, etc.)
• HDMI cables (not included)
• CAT cables (not included)
4
PackageContents
2x4 HDMI 2.0 Splitter/Extender
• 1x 2x4 HDMI 2.0 Splitter/Extender
•4x Plastic cushions
•4x IR Receiver cables
•1x IR Emitter cable
•1x RS232 Cable (3-pin to DB9)
•1x IR cable (3.5mm (m) to 3.5mm (m)) used for IR
cascade
• 1x Power adapter (12V/2A)
• Surface mount accessories
•1x User guide
CAT 6/7 Receiver
• 4x CAT6/7 Receivers
5
Product Layout
Figure 1: 2x4 HDMI 2.0 Splitter/Extender Front Panel Layout
1 Power LED
Off: No power
On: Splitter/Extender is powered on
Blinking: Splitter/Extender is in standby mode
2 HDMI Input LED On: HDMI input signal detected
Flashing: HDMI input source not detected
3SelectButton
Press to switch to the next source device
Press and hold for 3 seconds to switch between
manual switching mode and automatic
switching mode
4 EDID DIP Switch Select between Lo-Res, Default, Hi-Res modes.
See EDID Management on page 14
6
Figure 2: 2x4 HDMI 2.0 Splitter/Extender Rear Panel Layout
1 HDMI Input (1-2) Connects to an HDMI source device
2
HDMI/Loop Connects to a local HDMI display
CAT 6/7 Out (1-4)
Connects to the Input of the CAT 6/7 Receivers.
It supports PoC to power the receiver. The
orange LED illuminates when an HDMI signal
is detected. The green LED illuminates when
powered on
3
IR All In
Connects to IR Receiver cable. Sends IR signals
to all CAT 6/7 Receivers to control all the
display devices.
Connects to the IR Loop Out of the previous
Splitter/Extender for cascading
IR In (1-4)
Connects to IR emitter cable. Sends IR signals to
the respective CAT 6/7 Receiver to control the
display device
4
IR Out 3.5mm jack for controlling the source device
from the CAT 6/7 Receivers
IR Loop Out Connects to the IR All In port of the next splitter
RS232 Connects to the control PC using an RS232 cable
(cable not included)
FW USB Type-A port for firmware update
5
S/PDIF Audio Out Toslink output for audio de-embedding from
the HDMI output
L/R Audio Out 3.5mm analog stereo audio output for audio de-
embedding from the HDMI output
6 DC 24V Connects to the included 24V power adapter
7
Figure 3: CAT 6/7 Receiver Front and Back Panel Layout
1HDMIOut ConnectstoanHDMIdisplay
2 CAT 6/7 In
Connects to the Splitter/Extender's
CAT 6/7 outputs using a CAT cable.
It supports PoC to power the CAT
6/7 Receiver over CAT cable
Orange LED: On when an HDMI
signal is detected
Green LED: On when the receiver is
powered on
3 IR In Connects to the IR receiver cable
4 IR Out Connects to the IR emitter cable
8
Hardware Installation
1. Power off all devices including your HDMI
source(s) and HDMI display(s).
2. Connect your HDMI source device(s) to the 2x4
HDMI 2.0 Splitter/Extender's HDMI Input
connector(s)with HDMI cable(s) (HDMIcablesnot
included).
3. Connect your CAT cables between the Splitter/
Extender and CAT 6/7 Receivers.
4. Optional: Connect an HDMI display to the HDMI
Output connector of the Splitter/Extender using
an HDMI cable (HDMI cable not included). This
connection is needed only if you require local
monitoring of the HDMI signal.
5. Connect an HDMI display to each CAT 6/7
Receiver's HDMI Out connector with an HDMI
cable (HDMI cables not included).
6. Optional: Connect the IR Receiver cables and the
IR Emitter cable to the IR interface ports. This
connection is needed only if you need to control
your HDMI devices from the remote location. See
IR Control, starting on page 11, for proper IR
connection.
7. Plug the included power adapter into the Splitter/
Extender'sPowerJack,thenplugthepoweradapter
into a reliable power outlet. Note: The CAT 6/7
Receivers do not need power adapters, they can be
powered from the Splitter/Extender over CAT
cable with PoC technology.
8. Power on your HDMI source device(s) and HDMI
display(s). The Splitter/Extender is ready for use.
9
ApplicationDiagram
The application diagram shows the most typical input
and output devices used with the Splitter/Extender.
Figure 4: Application Diagram
CAT Cable Wiring
We suggest both RJ-45 connectors be wired identically
using T568B wiring standard for the best performance
and compatibility.
10
Source Device Switching
Manual Switching
Press the Select button to switch to the next source device,
the corressponding input LED will light up.
Auto Switching
Press and hold down the Select button for at least 3
seconds to enable auto-switching mode. The operating
parameters are shown below.
• TheSplitter/Extenderwillswitchtothefirstavailable
active input starting with HDMI In 1
• New Input: When a new source device is detected,
the Splitter/Extender will automatically switch to it
• SourceRemoved:When an activesourceisremoved,
theSplitter/Extenderwillswitchtothe first available
active source
• Power Off: The Splitter/Extender saves the last
configuration before powering off. If the last
switching mode is auto switching, the splitter will
automatically enter auto switching mode when it is
restarted. Then if the last selected source input is
still available, the Splitter/Extender will switch to
it. Otherwise, it will switch to the first available
active source input.
Indice
Altri manuali gofanco Estensione
gofanco
gofanco 4K120 Manuale utente
gofanco
gofanco HDEXT120ESD Manuale utente
gofanco
gofanco CAT5E Manuale utente
gofanco
gofanco KVMHDExt4K Manuale utente
gofanco
gofanco HDwireless100 Manuale utente
gofanco
gofanco HDMIExt8P Manuale utente
gofanco
gofanco HDwireless150 Manuale utente
gofanco
gofanco HDbitT4Pv2 Manuale utente
gofanco
gofanco KVMHD20Ext Manuale utente
gofanco
gofanco HDbitT8P Manuale utente
gofanco
gofanco HD20Ext4P-LT Manuale utente
gofanco
gofanco HDBaseT4P-4K Manuale utente
gofanco
gofanco HDwireless100-LT Manuale utente
gofanco
gofanco HD14Ext-EDID Manuale utente
gofanco
gofanco HDwireless10x1 Manuale utente
gofanco
gofanco HDExt Manuale utente
gofanco
gofanco AudioCATExt500 Manuale utente
gofanco
gofanco HDWirelessKVM Manuale utente
gofanco
gofanco HDExt50 Manuale utente
gofanco
gofanco HDMIExt4P Manuale utente
