Grizzly H0584 Manuale utente

Product Information

• 6,000 RPM

• Requires 90 PSI

• Requires 12 CFM

• Requires 5" hook and loop sanding disc

• 1/4" NPT air inlet

• Weighs 4 lbs.

Inventory

A. Air Sander ....................................................1

B. Plastic Hose .................................................1

C. Dust Collection Bag ......................................1

D. Wrench .........................................................1

MODEL H0584

DUAL ACTION SANDER

INSTRUCTION SHEET

EYE INJURY HAZARD!

Always wear safety glasses

when using this tool to

prevent serious personal

injury.

INJURY HAZARD!

Always disconnect tool from

air to prevent unexpected

operation during service.

DUST HAZARD!

Always wear respirator when

using this tool. Figure 1. Model H0584 inventory.

Assembly

To assemble the Model H0584:

1. Install a 1⁄4" NPT male quick-connect fitting

(not included) into the sander hose.

2. Attach a 5" hook and loop sanding disc to the

sanding pad as shown in Figure 2.

Figure 2. Attaching sanding disc.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL8321 PRINTED IN TAIWAN

DO NOT EXCEED 120 PSI!

Personal injury could

occur.

Throttle

Lever

Maintenance

Lubricate at the beginning of the sanding task.

Place one or two drops of pneumatic tool oil

directly into the air fitting as shown in Figure 5.

Figure 5. Lubricating directly into air fitting.

Operation

To operate the sander:

1. Plug the tool into compressed air.

2. Hold the sander and press the throttle lever

(Figure 4) to operate the sander.

A filter/lubricator/regulator set up is not recom-

mended, as excess oil in the tool could spray onto

the workpiece.

Before installing the sanding disc, run the sander

for a few minutes to eject excess oil, then wipe the

tool down with a rag and begin sanding. Oil the

tool after use or storage.

Service

To replace the sanding pad:

1. Slide the included wrench between the sand-

er and the sanding pad and insert it onto the

spindle as shown in Figure 6.

3. Turn the regulator knob (Figure 4) to adjust

the speed of the sanding disc.

4. Remove pressure on the throttle lever to stop

the sander.

5. When the sandpaper loses its effectiveness,

disconnect the tool, remove sandpaper

from the pad, and replace with a new disc.

Figure 4. Sander controls.

Figure 6. Wrench inserted onto spindle.

2. Hold the wrench and rotate the pad counter-

clockwise to remove it.

3. Install a new sanding pad (Part PH0584040)

and secure it with the wrench.

If you need help with your new pneumatic tool,

call our Tech Support at: (570) 546-9663.

Wrench

Sanding

Pad

3. Attach the plastic hose to the sander as

shown in Figure 3A, insert the plastic hose

into the dust collection bag, and secure with

the strings (Figure 3B).

Figure 3. Attaching plastic hose to sander and

dust collection bag.

Regulator

Knob

H0584 Parts Breakdown and List



















 













  





 















 













REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PH0584001 THROTTLE LEVER 22 PH0584022 CYLINDER PIN

2 PRP73M ROLL PIN 4 X 30 23 PH0584023 CYLINDER O-RING

3 PH0584003 VALVE PIN 24 PH0584024 CYLINDER

4 PH0584004 VALVE BODY 25 PH0584025 CYLINDER PIN

5 PH0584005 O-RING 26 PH0584026 REAR PLATE

6 PH0584006 THROTTLE VALVE 27 P6200 BALL BEARING 6200ZZ

7 PH0584007 VALVE SPRING 28 PH0584028 MOTOR GASKET

8 PH0584008 MOTOR HOUSING 29 PH0584029 PAD COVER

9 PR36M EXT RETAINING RING 7MM 30 PSB23M CAP SCREW M4-.7 X 12

10 PH0584010 O-RING 31 PH0584031 COTTON RING

11 PH0584011 REGULATOR 32 PH0584032 CRANK SHAFT

14 PH0584014 AIR ADAPTOR 33 PH0584033 KEY

14-1 PH0584014-1 PLASTIC HOSE 34 PH0584034 SCREW

14-2 PH0584014-2 DUST BAG 35 PH0584035 LOWER WEIGHT

15 PSB50M CAP SCREW M5-.8 X 10 36 P6202 BALL BEARING 6202ZZ

17 P6200 BALL BEARING 6200ZZ 37 PH0584037 SPECIAL WRENCH

18 PH0584018 FRONT PLATE 38 PH0584038 RANDOM SHAFT

19 PH0584019 ROTOR 39 PR29M INT RETAINING RING 32MM

20 PH0584020 VANE SPRING 40 PH0584040 SANDING PAD

21 PH0584021 VANE

Altri manuali Grizzly Levigatrice

Grizzly

Grizzly G1015 Manuale utente

Grizzly

Grizzly G0458 Guida rapida

Grizzly

Grizzly G0458Z Manuale utente

Grizzly

Grizzly H0594 Guida rapida

Grizzly

Grizzly G0529 Manuale utente

Grizzly

Grizzly G0563 Manuale utente

Grizzly

Grizzly Line Boring Machine G0642 Manuale utente

Grizzly

Grizzly G0486/G0487 Manuale utente

Grizzly

Grizzly H3140 Manuale utente

Grizzly

Grizzly G0458 Manuale utente

Grizzly

Grizzly G1140 Manuale utente

Grizzly

Grizzly G0563 Guida rapida

Grizzly

Grizzly T33256 Manuale utente

Grizzly

Grizzly G1015 Manuale utente

Grizzly

Grizzly G1079R Manuale utente

Grizzly

Grizzly G0723 Manuale utente

Grizzly

Grizzly G5049Z Manuale utente

Grizzly

Grizzly G0489 Manuale utente

Grizzly

Grizzly G0489 Guida rapida

Grizzly

Grizzly T10745 Manuale utente

Grizzly

Grizzly G9983 Manuale utente

Grizzly

Grizzly G8749 Manuale utente

Grizzly

Grizzly G0518 Manuale utente

Grizzly

Grizzly G0702 Manuale utente

Manuali Levigatrice popolari di altre marche

Oliver

Oliver 6305 Manuale utente

Jet

Jet 22-44 Pro-3 Manuale di servizio

Makita

Makita M9204 Manuale

Makita

Makita M9204 Manuale utente

Craftsman

Craftsman 351.215131 Manuale utente

Clarke

Clarke Woodworker CBS1-5B Manuale di istruzioni

Chicago Pneumatic

Chicago Pneumatic CP9778 Manuale utente

Nitto Kohki

Nitto Kohki BB-20 Manuale utente

Ferm

Ferm FEOS-135 Manuale utente

Unior

Unior 1510 Manuale utente

stayer

stayer ls1200 Manuale utente

Jet

Jet JSG-96 Manuale di servizio

Parkside

Parkside PDS 290 B2 Manuale utente

Status

Status XPA Series Manuale utente

Clarke

Clarke EZ Sand Manuale utente

Craftsman

Craftsman 113.22521 Manuale utente

Craftsman

Craftsman 113.225831 Manuale utente

CLAS

CLAS OP 1429 Manuale utente